TC Electronic Gold Channel User Manual page 32

UTILITY
The Utility Display
In Utility you can choose between CONFIG, CARD and
MIDI. Use the < > Menu keys to select between the
three displays.
The Config. Page
In the Config. page you can set up a number of global parameters
for the Gold Channel such as memory protect, MIDI bulk dump
etc.
Display Viewing Angle
Adjust for best contrast of the LCD display.
Clip Hold
Here you can set the time you want the Clip indicator to stay lit
after a clip is detected (Off, 5sec, 30sec or 60sec).
PAD range
Selects how many of the PAD values you want to have access to.
If set to 20 you are only able to scroll between 0 and 20 dB,
when set to 40 you have 0, 20 and 40 dB available and if set to
60 you have 0, 20, 40 and 60 dB PAD choices. This is done to
make it easier for you to control the PAD, because if you only
use 0 and 20 dB PAD in your daily work, it's irritating to scroll
through 40 and 60 every time you press the PAD key.
Param. dial direction
This parameter enables you to change the cursor direction when
dialing the Parameter wheel in parameter lists. Choose whether
the cursor should move up or down when dialing the parameter
wheel clockwise.
Auto Pages
Selects how the Gain and Signal pages shall react when
parameters are changed. Enter And Exit cause the pages to pop
up and disappear automatically. Enter At Touch, causes the pages
to pop up automatically but not to change back automatically.
Off means that nothing will happen automatically
Double Click
Turns the bypass buttons double click function on/off.
Fader Control
Selects what channels the TC Master Fader should control on the
Master output level. When set to Stereo the two outputs will
always be identical.
Fader Calibration
Press Enter to enable calibration of the optional TC Master Fader
connected to the External Control input. Follow the instructions
in the display.
Protect
Sets the Preset Protect function On/Off.
32
Protect Low limit
Sets the lower limit of the preset protect. The current number is
included in the protection.
Protect High limit
Sets the higher limit of the preset protect. The current number is
included in the protection.
The Card Page
The Card page features a number of tools for handling cards,
including preset copying to and from a Card.
Use the Parameter wheel to scroll, and the Value wheel to change
values.
Card type: SRAM PCMCIA, type 1, min. 64 KBytes to 2 MB.
Show card status
This function makes it possible to check the status of your PC-
card. The Gold Channel will be able to display the size of the
card, the write protection status, the number of presets on the
card and the amount of free space.
NOTE: This information will only be available when the card is
Gold Channel formatted or contains Gold Channel presets. The
Gold Channel will read "New Card" when the card is inserted, if
the card is not formatted.
Format/Erase Card
This function will Format and Erase the PC-card. Press Enter
twice to confirm this action.
WARNING: This action will overwrite ALL existing presets on
the current Card.
USER/CARD BANK COPY
This section makes it possible to copy a specified group of
presets to or from a specific space on a card. For example: You
want to copy User preset 10-15 from the Gold Channel to preset
5-10 on your card. Now set the "User bank preset start" at 10
(because you to start the group of presets at #10), the "Card bank
preset start" at 5 (because you want the first copied preset to start
at #5), the "Number of presets" to 5 (because that is the number
of presets you want to copy). Now select Copy "From User bank
to Card" scroll to "Execute copy" and press Enter twice to
confirm the copy operation.
User bank preset start
This parameter determines where the copy action should start in
the internal User bank.
Card bank preset start
This parameter determines where the copy action should start in
the Card bank.
Number of presets
This parameter sets the number of presets to be copied.