Care And Maintenance; Specifications; Troubleshooting - Stanley J5C09 Instruction Manual

4. Turn on the Compressor Power Switch.
5. Check pressure with the pressure gauge.
6. When desired pressure is reached, open thumb latch and remove the SureFit™ nozzle connector from the valve stem.
7. Turn off Compressor Power Switch.
8. Allow unit to cool before storing away.
9. Store compressor hose and tire fitting in storage compartment.
Inflating Other Inflatables without valve Stems
Inflation of other items requires use of one of the adapters (nozzles).
1. Select the appropriate adapter nozzle.
2. Lift the thumb latch on the SureFit™ nozzle, insert the adapter (i.e. needle) into the SureFit™ nozzle connector and close
thumb latch.
3. Insert adapter (i.e., needle) into item to be inflated.
4. Turn on the Compressor Power Switch — inflate to desired pressure or fullness.
IMPORTANT NOTE: Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
5. Remove adapter.
6. Switch the Compressor Power Switch off.
7. Allow unit to cool before storing away.
8. Store compressor hose and tire fitting in storage compartment.
WARNING: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN
THE "SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS" SECTION OF THIS INSTRUCTION MANUAL.

CARE AND MAINTENANCE

All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit is not in use, we
recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth moistened with a mild
solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Contact manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be disposed of properly. Recycling is
required, contact your local authority for information. Failure to comply with local, state and federal regulations can
result in fines, or imprisonment.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result
in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
12 volt DC charger plug fuse replacement (optional accessory)
The fuse in the plug end of the 12 volt DC charger protects the adapter' s charging circuit. If the 120 volt AC charger operates, but the DC
charging adapter does not, then this fuse may be opened (blown).
To replace the fuse:
1. Unscrew the end cap of the DC plug (counterclockwise).
2. Remove spring center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 8 amp volt fuse.
5. Replace the fuse, spring, contact and end cap.
6. Screw end cap clockwise until it is finger tight – DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 Volt DC Charging Adapter.

TROUBLESHOOTINg

Unit will not charge
• Make sure all of the unit' s functions are turned off.
• Make sure a suitable gage extension cord is properly connected to both the unit and a functioning AC outlet.
Unit Fails to Jump-Start
• Make sure unit' s power switch is in the on position.
• Check that jump-starter has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
USB Power Port will not power appliance
• Make sure the USB Charging Port Power Button is in the on position.
• Check that jump-starter has a full charge. Recharge unit if necessary.
LED Area Light does not come on
• Make sure the LED Area Light ON/OFF button is in the on position
• Check that jump-starter has a full charge. Recharge unit if necessary.
Portable Compressor will not inflate
• Make sure the Compressor Power Switch is in the on position.
• Check that jump-starter has a full charge. Recharge unit if necessary.
• Make sure connector is pushed to valve stem and thumb latch is closed when attempting to inflate tires; or nozzle (adapter) is
securely inserted into connector (chuck) on all other inflatables.

SPECIfICATIONS

Boost Ampere: 12Vdc, 500A
instantaneous
Battery Type: Maintenance-free, sealed lead acid, 12 volt DC, 19aH
Area Light: 1 long-life white LED
USB Port: 5Vdc, 500mA
DC Accessory Outlet: 12Vdc, 5A
Compressor Maximum Pressure: 120 PSI
Discover a comprehensive collection of battery chargers and jump starters on our website.
, 5 seconds 300A