Related Manuals for Samsung AM NN4 EH Series
Summary of Contents for Samsung AM NN4 EH Series
- Page 1 Air conditioner User manual AM***NN4*EH*** • Thank you for purchasing this Samsung air conditioner. • Before operating this unit, please read this user manual carefully and retain it for future reference.
-
Page 2: Table Of Contents
Contents Safety Information Safety Information At a Glance Indoor Unit Overview Operation Features Operating temperature and humidity • Pairing an indoor unit with a remote control Cleaning and Maintenance Cleaning and Maintaining Cleaning the indoor unit exterior • Cleaning the outdoor unit heat exchanger • Cleaning the air filter •... -
Page 3: Safety Information
Before using your new air conditioner, please read this manual thoroughly features and functions of your new appliance. characteristics of your air conditioner may differ slightly from those described in help and information online at www.samsung.com. WARNING CAUTION Hazards or unsafe practices that may result in minor personal injury or property damage. - Page 4 Safety Information The installation of this appliance must be performed by a qualified technician or service company. • Failing to do so may result in electric shock, fire, explosion, problems with the product, or injury. Install a switch and circuit breaker dedicated to the air conditioner. •...
- Page 5 CAUTION Install your appliance on a level and hard floor that can support its weight. • the product. Install the drain hose properly so that water is drained correctly. • When installing the outdoor unit, make sure to connect the drain hose so that draining is performed correctly.
- Page 6 Safety Information FOR USING WARNING If the appliance is flooded, please contact your nearest service centre. • Failing to do so may result in electric shock or fire. If the appliance generates a strange noise, a burning smell or smoke, unplug the power plug immediately and contact your nearest service centre.
- Page 7 After unpacking the air conditioner, keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children. • Do not touch the front panel with your hands or fingers during the heating operation. •...
- Page 8 Safety Information CAUTION Do not place objects or devices under the indoor unit. • Water dripping from the indoor unit may result in fire or property damage. Check that the installation frame of the outdoor unit is not broken at least once a year.
- Page 9 This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
-
Page 10: At A Glance
Indoor Unit Overview The indoor unit and its display may look slightly different from the illustration shown below, depending on the model and the panel type. 01 Display Indication Function On/Off operation indicator Timer indicator Filter cleaning indicator Remote control sensor 02 Air flow blade/Air outlet (inside) / Wind-Free panel (You can use the Wind-Free Cooling function... -
Page 11: Operation Features
Operation Features Operating temperature and humidity When using the air conditioner follow the operating temperature and humidity ranges. Mode Indoor temperature Outdoor temperature Indoor humidity Cool mode 18~32 °C Depending on the outdoor Dry mode 80% or less unit specification Heat mode 30 °C or less CAUTION... -
Page 12: Cleaning And Maintenance
Cleaning and Maintaining Cleaning and Maintaining Before cleaning the indoor unit, be sure to turn off the auxiliary power switch. Cleaning the indoor unit exterior Wipe the surface of the unit with a slightly wet or dry cloth when needed. Wipe off dirt of odd- shaped areas by using a soft brush. - Page 13 Push down the hooks at each side of the front grille to open the grille. NOTE • The hooks are located on both sides of the front grill with the Samsung logo. Pull out the air filter from the indoor unit. 2 Cleaning the air filter CAUTION Do not scrub the air filter with a brush or other cleaning utensil.
- Page 14 Cleaning and Maintaining 3 Reassembling the air filter CAUTION • If the indoor unit is used without the air filter, the indoor unit may be damaged due to dust. 4 Resetting the air filter After cleaning and reassembling the air filter, be sure to reset the filter-cleaning reminder as •...
- Page 15 Periodical maintenance Requires qualified Unit Maintenance item Interval technicians Clean the air filter. At least once a month Clean the condensate drain pan. Once a year Indoor Clean up the heat exchange. Once a year unit Clean the condensate drain pipe. Replace the remote control batteries.
- Page 16 Cleaning and Maintaining Troubleshooting unnecessary expense. Problem Solution The air conditioner • does not operate immediately after it conditioner will start in 3 minutes. has been restarted. • Check if the power plug is properly connected. • Check whether the auxiliary power switch (MCCB, ELB) is turned on. •...
- Page 17 Problem Solution The wired remote • Check whether the indicator is displayed at the bottom right of the control does not remote control display. In this case, turn off both the air conditioner and operate. The air conditioner is not turned on or •...
- Page 18 Cleaning and Maintaining Problem Solution • Close the windows and doors to maximize the cooling and heating efficiencies. • If the Cool mode is stopped and then started immediately, cool air comes out after about 3 minutes to protect the compressor of the outdoor unit. The air is not cool or warm enough.
-
Page 19: Technical Specifications
Technical specifications Type Model Net weight(kg) dimension(W x D x H) (mm) AM045NN4DEH 840 x 840 x 204 AM056NN4DEH 840 x 840 x 204 AM071NN4DEH 840 x 840 x 204 Indoor unit AM090NN4DEH 840 x 840 x 204 AM112NN4DEH 16.5 840 x 840 x 246 AM128NN4DEH 18.5... -
Page 20: Installation Procedure
Installation Procedure Step 1 Installing the indoor unit CAUTION When deciding on the location of the air conditioner the • Make sure that the ceiling is strong enough to support following restrictions must be taken into account. the weight of the indoor unit. Before hanging the unit, test the strength of each attached suspension bolt. - Page 21 7 Adjust the unit to the appropriate position, taking into Step 3 Insulating the refrigerant pipes account the installation area for the front panel. • Place the pattern sheet on the indoor unit. system, you can insulate the piping and hose. •...
- Page 22 Installation Procedure CAUTION Insulation Type (Heating/Cooling) • Must fit tightly against body without any gap. High Standard Pipe size humidity Pipe Remarks • Make sure that all refrigerant connection must be (mm) [30°C, [30°C, over accessible for easy maintenance and detachment. 85%] 85%] •...
- Page 23 Step 4 Installing the drain hose and • drain pipe Air ventilation the drain socket. 2 Tighten the metal clamp as shown in the picture. Ceiling • If it is necessary to increase the height of the drain pipe, install the drain pipe straight within 300 mm from the drain hose port.
- Page 24 Installation Procedure • Install horizontally. • Max. allowable bending angle. Be horizontal Indoor unit Indoor unit Flexible hose NOTE • Max. allowable axis gap. • If a concentrated drain pipe is installed, refer to the figure below. Indoor unit Max. 20 mm Hanger 1~1.5m Main air vent...
- Page 25 Step 5 Connecting the power and • To protect the product from water and possible shock, you should keep the power and the communication communication cables cables of the indoor and outdoor units in the iron pipe. • Connect the power cable to the auxiliary circuit Power and communication cable connection breaker (ELCB, MCCB, ELB).
- Page 26 Installation Procedure Selecting the crimping terminal lug 1 Select the crimping terminal lug based on the norminal dimension of the power cable. Silver solder Norminal Norminal dimensions dimensions Standard Standard Standard Standard Allowance Allowance Allowance Allowance for cable for screw dimension dimension dimension...
- Page 27 Specifications of the terminal blocks NOTE • • Communication: M3.5 screw AC power: M4 screw Rated currents Model Rating current(A) AM045NN4DEH* 0.22 AM056NN4DEH* 0.22 AM071NN4DEH* 0.31 AM090NN4DEH* 0.43 AM112NN4DEH* 0.55 Power supply MCCB AM128NN4DEH* 0.51 (single phase) AM140NN4DEH* 0.62 XA, 30 mA 0.1 s 2 Decide the power cable specification and maximum Communication...
- Page 28 Installation Procedure Step 6 Setting the indoor unit CAUTION addresses and the installation options • SEG24. You cannot set both of the indoor unit addresses and • Because SEG1, SEG7, SEG13, and SEG19 are the page automatically. Common steps for setting the addresses and •...
- Page 29 Steps Remote control display (Low Fan) button repeatedly until the SEG2 (High Fan) button repeatedly until the When you press the (Low Fan) or SEG3 2 Press the (Mode) button. Cool and On appear on the remote control display. (Low Fan) button repeatedly until the SEG4 (High Fan) button repeatedly until the When you press the...
- Page 30 Installation Procedure Steps Remote control display (High Fan) button repeatedly until the When you press the (Low Fan) or SEG8 6 Press the (Mode) button. Fan and On appear on the remote control display. (Low Fan) button repeatedly until the SEG9 (High Fan) button repeatedly until the When you press the...
- Page 31 Steps Remote control display 10 Press the (Mode) button. Auto and Off appear on the remote control display. (Low Fan) button repeatedly until the SEG14 (High Fan) button repeatedly until the When you press the (Low Fan) or SEG15 12 Press the (Mode) button.
- Page 32 Installation Procedure Steps Remote control display (High Fan) button repeatedly until the When you press the (Low Fan) or SEG20 16 Press the (Mode) button. Fan and Off appear on the remote control display. (Low Fan) button repeatedly until the SEG21 (High Fan) button repeatedly until the When you press the...
- Page 33 (Mode) button repeatedly [SEG2, SEG3] [SEG4, SEG5] [SEG6, SEG8] [SEG9, SEG10] [SEG11, SEG12] [SEG14, SEG15] [SEG16, SEG17] [SEG18, SEG20] [SEG21, SEG22] [SEG23, SEG24] Point the remote control to the remote control sensor on the indoor unit and then press the (Power) button (Power) button again.
- Page 34 Installation Procedure Setting the indoor unit addresses (MAIN/RMC/ 3 Set an address (MAIN/RMC/MCU port) for each indoor MCU) unit using the remote control, according to your air conditioning system plan. 1 Make sure that the power is supplied to the indoor •...
- Page 35 Option SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 Setting MCU PORT 10-digit of MCU Function Page 1-digit of MCU MCU PORT address address address Indication Details Indication Details Indication Details Indication Details Indication Details No MCU PORT Indication PORT and details 10-digit 1-digit PORT...
- Page 36 Installation Procedure Installation options for the 02 series SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Use of external room temperature FAN RPM sensor / Minimizing Use of central control compensation fan operation when thermostat is off SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 Use of hot water EEV Step when...
- Page 37 02 series installation option (Detailed) Option No. : 02XXXX-1XXXXX-2XXXXX-3XXXXX Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Use of external room temperature sensor / Explanation PAGE MODE Use of central control FAN RPM compensation Minimizing fan operation when thermostat is off Details Use of External Minimizing fan...
- Page 38 Installation Procedure Option SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 Setting the output of external control / External heater signal Explanation PAGE Use of external control S-Plasma ion Buzzer control Hours of filter usage / Cooling operation signal / Free Cooling control signal Indication Details Indication...
- Page 39 (*3) it as cool mode. (*4) When the following 2 or 3 is used as external heater On/Off signal, the signal for monitoring external contact control will not be output. it as cool mode. - If Fan is set to off for cooling only indoor unit by setting the SEG9=3 or SEG15=3, you need to use an external sensor or wired remote controller sensor to detect indoor temperature exactly.
- Page 40 Installation Procedure 05 series installation option (Detailed) Option No. : 05XXXX-1XXXXX-2XXXXX-3XXXXX Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 (When setting SEG3) (When setting SEG3) (When setting SEG3) for HR only in Auto mode / Explanation PAGE MODE Standard heating temp. Standard cooling temp.
- Page 41 Option SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 Explanation Details Indication Details Indication Set temp. for heater On/Off Delay time for heater On At the same time as No delay thermo on At the same time as 10 minutes thermo on At the same time as 20 minutes thermo on...
- Page 42 Installation Procedure (*1) at the lowest place. For example, When the indoor unit is installed 40m higher than the indoor unit installed at the lowest place, select the option “1”. (*2) The difference between the pipe length of the indoor unit installed at farthest place from an outdoor unit and the pipe length of the corresponding indoor unit from an outdoor unit.
- Page 43 Changing the addresses and options individually Common steps for setting the addresses and options on page 28. Option SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 Tens position Units position Type of the Function Page Mode of the option of the option option to change number number...
- Page 44 *8000 (apel in retea) ROMANIA www.samsung.com/ro/support 08008-726-78-64 (08008-SAMSUNG) Apel GRATUIT CYPRUS 8009 4000 only from landline, toll free www.samsung.com/gr/support 80111-SAMSUNG (80111 726 7864) only from land line GREECE www.samsung.com/gr/support (+30) 210 6897691 from mobile and land line LITHUANIA 8-800-77777 www.samsung.com/lt/support...