Manual JES-370
Es ist zu überprüfen, ob die Gerätelieferung Ihrer Bestel-
lung entspricht.
6.
Installationsvorschriften
•
Bei Arbeiten am elektrischen Teil des Gerätes ist es
vom Netz zu trennen.
•
Das Gerät muss entsprechend den örtlich geltenden
Vorschriften angeschlossen und geerdet werden.
•
Für einen sicheren Betrieb der Sonde ist diese mit
einer verriegelnd abschaltenden Untertemperatur-
überwachung ausgestattet. Die Rücksetzung erfolgt
durch spannungsfrei Schalten der Elektronik.
•
Der Betreiber ist angehalten, den potentialfreien
Statuskontakt zu benutzen bzw. zu überwachen.
Nur dies gewährt einen sicheren Betrieb der Sonde.
•
Es ist zwingend notwendig, die Elektronik vor Strah-
lungshitze zu schützen. (Thermische Isolation). Die
maximale Umgebungstemperatur darf 55°c nicht
überschreiten.
•
Die Flanschtemperatur darf 320°c nicht überschrei-
ten, sonst ist eine konstruktive Änderung, z.B: Ein-
satz eines Thermal Spacers, notwendig.
•
Die Sonde muss immer mit einer Mindestneigung
von 5° gegen das Entnahmerohr hin montiert wer-
den. Dies ist erforderlich um einen allfällig möglichen
Rückfluss des kondensates in die Entnahmesonde
zu verhindern.
6.1.
Montage
•
Entnahmerohr und/oder Vorfilter mit Dichtung am
Sondenflansch montieren.
•
Sonde mit Dichtung am Prozessflansch montieren.
•
Einbauwinkel gemäß technischer Spezifikation be-
achten.
•
ABS-Filtergehäuse mit ABS Filterkugeln befülllen
und mit Spannverschluss am Anschlusskopf mon-
tieren. Auf korrekte Ausrichtung des Filtergehäuses
(siehe Foto) sowie auf Sitz der O-Ring Dichtung
achten!
––––––––––––––––––––––––––
BA_DE_JES370_v1.3
check instrument and any other parts against order.
6.
Installation instructions
•
Disconnect mains before working on electrical part
of equipment.
•
The equipment has to be connected and grounded
according to the local rules and regulations.
•
In order to guarantee safe operation the electronic
is equipped with interlocking under temperature mo-
nitoring. For reset disconnect and connect power
again.
•
It is highly recommended to use the volt free status
contact. Only this assures a reliable operation of the
probe.
•
It is essentially necessary to keep the electronics
away from radiant heating (thermal insulation). The
ambient temperature must not exceed 55°c.
•
The flange temperature must not exceed 320°c. Ot-
herwise a change of construction is necessery, eg.
use of a thermal spacer.
•
The probe mounting has to be done always with a
minimum inclination of 5° towards the sampling pipe.
This is necessary to prevent a possible flow back
from condensate into the probe.
6.1.
Mounting
•
Mount sampling pipe and/or pre filter with gasket on
the flange of the gas sampling probe.
•
Mount probe with gasket on the process flange.
•
Take care for correct mounting angel according tech-
nical specification.
•
Fill ABS-filter housing with ABS-filter balls and mount
it with fastener on the connecting head. check the
correct alignment of the filter housing (see picture)
and the fitting of the o-ring gasket!
––––––––––––––––––––––––––
[ 12 / 30 ]