BFT ALTAIR-P Installation And User Manual

BFT ALTAIR-P Installation And User Manual

Hide thumbs Also See for ALTAIR-P:

Advertisement

QUADRO COMANDO
I
GB
CONTROL PANEL
CENTRALE DE COMMANDE
F
STEUERPLATINE
D
E
CUADRO DE MANDOS
P
QUADRO DE COMANDO
ISTRUZIONI D'USO E DI INSTALLAZIONE
INSTALLATION AND USER'S MANUAL
INSTRUCTIONS D'UTILISATION ET D'INSTALLATION
INSTALLATIONS-UND GEBRAUCHSANLEITUNG
INSTRUCCIONES DE USO Y DE INSTALACION
INSTRUÇÕES DE USO E DE INSTALAÇÃO
Via Lago di Vico, 44
36015 Schio (VI)
Tel.naz. 0445 696511
Tel.int. +39 0445 696533
Fax 0445 696522
Internet: www.bft.it
E-mail: sales@bft.it
D811506 ver.03 13-06-07
8
027908
2 9 5 4 8 4
ALTAIR-P

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ALTAIR-P and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for BFT ALTAIR-P

  • Page 1 027908 2 9 5 4 8 4 CENTRALE DE COMMANDE STEUERPLATINE CUADRO DE MANDOS QUADRO DE COMANDO ALTAIR-P ISTRUZIONI D’USO E DI INSTALLAZIONE INSTALLATION AND USER’S MANUAL INSTRUCTIONS D’UTILISATION ET D’INSTALLATION INSTALLATIONS-UND GEBRAUCHSANLEITUNG INSTRUCCIONES DE USO Y DE INSTALACION INSTRUÇÕES DE USO E DE INSTALAÇÃO...
  • Page 2 ALTAIR-P - Ver. 03...
  • Page 3 1) GENERAL OUTLINE Il quadro comandi ALTAIR-P è adatto per cancelli a battente. Viene fornito dal costrut- The ALTAIR-P control panel is suitable for swing gates. It is supplied by the manu- tore con impostazioni funzionali standard. Qualsiasi variazione, deve essere impostata facturer with standard functional settings.
  • Page 4: Installation Manual

    DIP PED-CLOSE= ON: 1) GENERAL OUTLINE CLOSE input (N.O.). The ALTAIR-P control panel is suitable for swing gates. It is supplied by the 31-32 Antenna input for integrated radio-receiver board manufacturer with standard functional settings. Any alteration must be set by (31: SIGNAL.
  • Page 5 OFF: In case of obscuring, the photocells are active both on opening and 6) CONFIGURATION on closing. When a photocell is obscured on closing, it reverses the The display programmer is used to set all the ALTAIR-P control panel motion only after the photocell is disengaged. functions.
  • Page 6 Transmitter versions which can be used: Following the diagram in Fig.5, proceed to connecting all the ALTAIR-P control panels, exclusively using a telephone-type line. Should a telephone cable with more than one pair be needed, it is indispens- all Rolling Code transmitters compatible with able to use wires from the same pair.
  • Page 7 KO! message (value or function error) No. manoeuvres since latest Menu scrolling maintenance (in thousands) (+ = preceding - = following) “Wait” message (enter value or function) No. radio control devices memorised FOLLOWING MENUS FIG. B 14 - ALTAIR-P - Ver. 03...
  • Page 8 Press P1 (pushbutton) on radio Release P1 on radio control device. control device Press the required T (key) on radio control device – see Fig. B3 Press the required T (key) on radio control device – see Fig. B3 ALTAIR-P - Ver. 03 -...
  • Page 9 Fig. 3 1 2 3 4 5 6 7 8 9 10 13 14 15 II CH 13 14 15 16 17 18 19 20 21 13 14 15 16 ANT. NC NO NO 36 - ALTAIR-P - Ver. 03...
  • Page 10 Contacts Contacts Contatos UNIFLAT Contacts Contacts UNITRC Kontakte Kontakte Contactos Contactos Contatos Contatos UNIMITTO UNITRC Contatti Contatti Contacts Contacts Contacts Contacts Kontakte Kontakte Contactos Contactos Contatos Contatos UNIMITTO UNITRC Contatti Contacts Contacts Kontakte Contactos Contatos ALTAIR-P - Ver. 03 -...
  • Page 11 Fig. 5 ALTAIR P SCS1 SCS1 SCS1 SCS1 Max. 250m Fig. 6A Fig. 6B 10 11 15 16 17 18 19 20 ScA 2ch=OFF 38 - ALTAIR-P - Ver. 03...

Table of Contents

Save PDF