Table of Contents
Advertisement
Quick Links
U P
®
ASME A112.18.1 / CSA B125.1
ASME A112.18.2 / CSA B125.2
ICC/ANSI A117.1
Model/Modelo/Modèle
65380LF & 65381LF
Siderna™ Series/Series/Seria
Write purchased model number here.
Escriba aquí el número del modelo comprado.
Inscrivez le numéro de modèle ici.
You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin:
For easy installation of your Brizo
faucet you will need:
• To READ ALL the instructions completely
before beginning.
• To READ ALL warnings, care, and maintenance
information.
• To purchase the correct water supply hook-up.
Para instalación fácil de su llave
Brizo
®
usted necesitará:
• LEER TODAS las instrucciones completamente
antes de empezar.
• LEER TODOS los avisos, cuidados, e
información de mantenimiento.
• Comprar las conexiones correctas para el
suministro de agua.
Pour installer votre robinet Brizo
facilement, vous devez:
• LIRE TOUTES les instructions avant de
débuter;
• LIRE TOUS les avertissements ainsi que toutes
les instructions de nettoyage et d'entretien;
• Acheter le bon nécessaire de raccordement.
C
®
®
®
TWO HANDLE WIDESPREAD
LAVATORY FAUCETS
LLAVES DE LAVAMANOS
EXTENDIDAS DE DOS MANIJAS
ROBINETS À ENTRAXE LONG À
DEUX POIGNÉES POUR LAVABO
L
1
L
2/5/10
Rev. B
Advertisement
Table of Contents
Related Manuals for Brizo Siderna Series
Summary of Contents for Brizo Siderna Series
- Page 1 Inscrivez le numéro de modèle ici. You may need / Usted puede necesitar / Articles dont vous pouvez avoir besoin: ® For easy installation of your Brizo faucet you will need: • To READ ALL the instructions completely before beginning.
- Page 2 This warranty excludes all industrial, commercial & business usage, whose purchasers are parts may be obtained by calling 1-877-345-BRIZO (2749) (in the U.S. and Canada) or by hereby extended a five year limited warranty from the date of purchase, with all other terms of writing to: this warranty applying except the duration of the warranty.
- Page 3 RP63757▲ Lift Rod Barra de Alzar Tige de Manoeuvre RP63758 Nut & Washer Tuerca y Arandela Écrou et Rondelle RP63758 Nut & Washer Tuerca y Arandela RP61825 Écrou et Rondelle Valve Cartridge, Hot Side Cartucho de la Válvula , Lado Caliente Cartouche de soupape, RP61824 eau chaude...
- Page 4 Notes / Notas / Notes 63479 Rev. B...
- Page 5 Install the nuts and washer (1) onto the end valve shank (2). Position Place spline adapters (1) over valve stems (2) and secure with screws (3). gasket (3) into the groove of adapter (4). Place the end valve shank through mounting hole from the bottom. From the top, thread the adapter Install gasket (1) into the groove in the bottom of the spout (4) onto the shank until it stops.
- Page 6 Snap the quick connect hose assembly (1) onto the spout nipple (2) and end valve nipples (3). Pull moderately to ensure each connection has been made. WARNING: DO NOT REMOVE the clip (4) from the hose assembly. Make connections to water lines. Choose hook-ups for 1/2" I.P.S. connections: (5) Ball nose riser (3/8"...
- Page 7 Pop-up Installation Remove pivot nut (1). Install horizontal rod (2) and Apply silicone to underside of flange (1). stopper (3) as removable (4) or non-removable (5). Insert body (2) into sink. Screw flange (1) Remove stopper (1) and flange (2). Hand tighten pivot nut (1).
- Page 8 Maintenance SHUT OFF WATER SUPPLIES BEFORE SERVICING FAUCET. If your faucet leaks out of spout outlet or around handle body, replace valve cartridge (1). A. Pull up on handle (2) to remove. NOTE: It is best if you pull straight up on the handle.
Need help?
Do you have a question about the Siderna Series and is the answer not in the manual?
Questions and answers
How do you remove the aerator from this Siderna faucet? It is recessed and does not screw in/out. Appears to just pull down, but do not have a tool to remove it.
To remove the aerator (flow restrictor) from the Brizo Siderna Series faucet:
1. Make sure the handles are in the off position.
2. Unsnap the hoses by squeezing the black plastic connector and pulling them off.
3. Unscrew the spout adapter.
4. Locate the flow restrictor inside the adapter.
5. Remove any debris using a small, soft brush.
This answer is automatically generated