Advertisement
1.2.
GENERAL SAFETY Continued
Disconnect the saw from the power supply before removing wood chips or dust.
!
Use a workpiece support when sawing material which extends beyond the saw table.
!
DO NOT operate the machine if damaged.
%
DO NOT operate the machine if any parts are missing as this may cause machine failure and/or personal injury.
%
DO NOT use saw blades which are damaged or deformed. Use only Sealey blades and spare parts. Non-standard blades can be dangerous.
%
DO NOT use as a saw unless the sanding disc guard is in place.
%
DO NOT use the sander without the sanding table attached.
%
DO NOT get the saw wet or use in damp or wet locations or areas where there is condensation and do not wet the sanding abrasive.
%
DO NOT expose the saw housing to flame or high temperature.
%
DO NOT allow untrained persons to operate the saw.
%
DO NOT use saw where there are flammable liquids, solids or gases such as paint solvents and including waste wipers and cleaning rags.
%
DO NOT leave the saw operating unattended.
%
DO NOT operate the saw when you are tired or under the influence of alcohol, drugs or intoxicating medication.
%
DO NOT saw or sand materials containing asbestos.
%
DO NOT use the saw for a task it is not designed to perform.
%
When not in use switch off the saw and unplug from the mains power.
!
2. DESCRIPTION & SPECIFICATION
The SM1214 is fully approved to CE regulations. Fitted with powerful induction motor and features ball bearing type blade guides for precision
cutting. Fully guarded blade wheels. Integral sanding disc and sanding table. Both tables can be adjusted for angled cutting and sanding. Mitre
gauge included fits both tables. No-volt release switch prevents uncontrolled re-start after power interruption. Suitable for cutting wood, plastics
and thin metal sheet.
Motor Power . . . . . . . . . . . . . . . . . . . . . . . .375W
Power Supply . . . . . . . . . . . . . . . .230V.AC. - 1ph
Throat Depth . . . . . . . . . . . . . . . . . . . . . . .360mm
Max. Cutting Height . . . . . . . . . . . . . . . . . .145mm
Cutting Speed . . . . . . . . . . .160, 750, 1200m/min
Blade Length . . . . . . . . . . . . . . . . . . . . . .1784mm
Saw Table Size . . . . . . . . . . . . . . . . 400 x 400mm
3. ASSEMBLY
Unpack the saw and check contents for damage. Should there be any damaged or missing parts contact your supplier immediately.
Package content: Bandsaw, Saw Table, Sanding Table with Mounting Rod and Clamp Knob, Mitre Gauge, Fence, Sanding Belt, Sanding Disc, Circle
Cutting Attachment, Locking Screw x 2, Washer, Sanding Belt Stop x 2, Hex. Wrench x 2.
3.1.
Assembly
3.1.1. Remove the table aligning screw and clamp from the underside of the table (fig. 2).
3.1.2. Remove the table lock knob, spring and spring bush from the table support rod (fig. 3).
3.1.3. Place the saw table onto the saw frame with the saw blade passing through the slot in the
table. The table support rod goes through the curved slot in the tilt indicator, under the table.
3.1.4. Re-fit the spring bush, spring and knob to the table support rod.
3.1.5. Re-fit the table aligning screw and clamp.
3.1.6. Using a set square, position table at right angles to the blade and then adjust pointer to align with
0
on table scale.
O
3.1.7. Important! Bolt saw to a firm, stable work surface capable of supporting the saw and any
workpiece. DO NOT attempt to use the saw as a free-standing unit as it may topple over
during use and cause damage and/or personal injury.
3.1.8. Connect extraction port (fig. 1.A) to dust extractor system (if available).
4. ADJUSTMENTS
WARNING! ENSURE THE BANDSAW IS DISCONNECTED FROM THE MAINS
F
POWER SUPPLY BEFORE ATTEMPTING ANY ADJUSTMENTS.
p
4.1.
Changing the blade
4.1.1. Remove the saw table, and the sanding table, if installed.
4.1.2. Unscrew the two front cover retainers (fig. 1.B) and remove the cover.
4.1.3. Remove the two retaining screws (fig. 5.1) and lift off the upper blade guard (fig. 5.2).
4.1.4. Loosen the upper and lower blade guide locking screws (upper shown, fig. 4.1) and move the
guides (fig. 4.2) away from the blade.
4.1.5. Loosen the locking screws (upper shown, fig. 4.3) and move the upper and lower support
bearings (upper shown, fig. 4.4) away from the blade.
fig. 2
p
Saw Table Adjustment . . . . . . . . . . . . . . . 0 to 45
Sanding Disc . . . . . . . . . . . . . . . . . . . . . Ø150mm
Disc Speed . . . . . . . . . . . . . . . . . . . . . . . 1720rpm
Sanding Table Adjustment . . . . . . . . . . . . 0 to 45
Dust Extraction Port . . . . . . . . . . . . . . . . Ø50mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30kg
fig. 3
O
O
fig. 5
fig. 4
fig. 1
SM1214 - 1 - 280801
Advertisement
