Page 2
– Cortador de Relva Convencional – Trade Name: Appellation commerciale : Handelsbezeichnung: Handelsnaam: Firmanavn: Nome commerciale: Nombre comercial: Handelsnavn: Handelsbeteckning: Gravely Kauppanimi: Nazwa handlowa: Nome da Marca: Model: Modèle : Modell: Model: Model: Modello: Modelo: Modell: Modell: Malli: 988313...
Page 3
Philip J. Smucker: 11/24/2003 Quality and Conformance Manager (Keeper of Technical File) Date Date Datum Ariens Company Responsable de la qualité et de la conformité des produits Datum Dato Data (Dépositaire de la fiche technique) Manager Qualitätssicherung Fecha Dato Datum Brillion, WI 54110-0157 USA und Konformität (Archivar der technischen Akte) Kwaliteits- en Päiväys Data Data...
THE MANUAL PRODUCT REGISTRATION Before operation of unit, carefully and completely read your The Gravely dealer must register the product at the time of manuals. The contents will provide you with an purchase. Registering the product will help the company...
5. Explain recommended lubrication and maintenance. 6. Instruct customer on controls and operation of unit. Advise customer on adjustments. Discuss and emphasize the Safety Precautions. Give customer Owner/Operator, Parts, and Engine Manuals. Advise customer to thoroughly read and understand them. SAFETY NOTATIONS WARNING: This cutting machine is capable...
Page 6
OL1801 OL4420 Keep children and others away from unit 3. Warning! while operating. (988100, 102, 103, 110, 112, 114, 115, 118, 119) Always stand clear of discharge. OL4370 OL0910 DO NOT operate mower unless guards are in operating position or bagger is attached.
Page 7
4. Danger! Wear adequate safety gear, protective gloves and footwear. NEVER wear open sandals or canvas shoes during operation. Stay clear of rotating parts. Protect eyes, face and head from objects that may be thrown from unit. Wear appropriate hearing protection. Sharp edges can cut.
Page 8
DO NOT operate at too fast a rate. DO NOT change engine NEVER fill fuel tank when engine is running or hot from governor settings or over-speed engine. Slow down and turn operation. corners slowly. NEVER fill or drain fuel tank indoors. Disengage PTO when attachment is not in use.
When held in neutral, the brakes are engaged. 1. Start engine and engage PTO. 2. Release operator presence control lever(s). Engine Steering Lever Latches (988100, 102, 103, 110, 112) must stop. The steering lever latches hold the steering levers in neutral 3. Disengage PTO.
Page 11
Shift into reverse and pull up on the lower control levers to move in reverse. When held in neutral, the brakes are engaged. Ignition Switch (988100, 102, 103, 110, 112, 114, 115, 118, 119, 313) Operate the ignition switch with the removable key.
Page 12
Check each item in Each Use in the Maintenance Schedule. To engage brake, loosen pivot bar NOTE: On 988100, 102, 103, 110, 112 the engine will not (1). start unless the shift lever is in neutral and the Power Take Pull pivot bar back against the Off (PTO) is Off.
Page 13
• To turn to the left, pull the left hand lever up. one drive wheel. 988100, 102, 103, 110, 112 To shift unit: 1. Stop unit movement by pulling both steering levers all OG1440 the way up.
Page 14
OG1610 CUTTING HEIGHT ADJUSTMENT • To turn to the left, push the right hand control lever Fixed Decks (988100, 102, 110, 112, 114, 115, 118, forward. 119, 313) 1. Shut off the unit. See Shut Off on page 12 and "To stop mowing."...
Page 15
IMPORTANT: Make sure lock pins are fully engaged. PARKING 6. Repeat adjustment for other side of deck. 988100, 102, 103, 110, 112 1. Shut off the unit. See Shut Off on page 12 and "To stop Fixed Deck Cutting Heights mowing."...
MAINTENANCE SCHEDULE Period Service Task Check Safety Interlock System WARNING: Safety interlock system failure and improper operation of unit can result in death or serious injury. Test this system each time the unit is operated. If this system does not function as described, do not operate until repairs are made.
3. Note which direction, if any, the unit pulls. steering control rod. 4. Stop unit and engine. 5. 988100, 102, 103, 110, 112: Adjust the clevis on the steering control rod until the gap between the ends of 5. Adjust tracking if needed.
Page 18
REPLACE TRACTION BELTS 1. Turn off the engine, remove the key and allow unit to cool. 2. Release the steering levers (988100, 102, 103, 110, 112). 3. Raise the rear of the unit so that the drive wheels are OG0752 off the ground.
Page 19
Note: 988100 Shown. 988114, 115, 118, 119, 313 Similar. OG1231 1. Transmission 3. 5/16-18 Bolts 2. Shift Lever Figure 12 To adjust: OG0751 1. Handlebar 6. Transmission Shaft 1. Stop the engine. Remove ignition key. Put PTO lever in 2. Steering Lever Pulley the "OFF"...
Page 20
REPLACE TRANSMISSION BELT 2. Measure the air gap between the armature and the rotor. 1. Stop the engine. Remove ignition key. Put PTO lever in Minimum: A .005" feeler gauge should slide between the "OFF" position. Put the shift lever in neutral. armature and rotor with slight contact.
Page 21
3. Remove deck cover. 1. Stop engine, remove key and wait for all hot parts to cool. 4. Remove deck idler spring. 2. Remove the deck belt idler spring from the spring 5. Remove belt from deck pulleys and mower clutch anchor.
Replace Mower Blades 1. Remove mower blade from unit. 1. Put the blades, flat washers, lock washers, and the Discard mower blade if: bolts back on the spindle shafts. • More than 1/2 in. (1.27 cm) of metal is removed. 2.
On position, and the Power Take Off (PTO) is Off (988100, 102, 103, 110, 112). The engine will not start unless the key is in the On position and the Power Take Off (PTO) is Off (988114, 115, 118, 119, 313) .
Page 28
GRAVELY A Division of Ariens Company 655 West Ryan Street P.O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www.gravely.com...