Programming Remote Controls - Overhead door Legacy 800 2026 Manual

7

PROGRAMMING REMOTE CONTROLS

A moving door can cause serious injury or death.
1. Keep people clear of opening while door is
moving.
2. Do NOT allow children to play with opener,
including wall control, remote control, or
Wireless Keypad.
3. During programming, the door opener could
begin to run, so keep people and objects
away from the moving door and its parts. To
keep the door from moving, close the door
and disconnect it from the Opener by pulling
the Emergency Release.
NOTE: Wall control will not operate until limits are
set.
NOTE: For remote control locate Box 3.
1a. Single Button Remote Programming.
NOTE: This opener can learn up to 7 single button
remote controls.
• Locate learn code button and indicator LED on
the power head (Fig. 7-1).
• Press and release learn code button.
– Indicator LED will blink RED at a rate of twice
per second.
• Within 30 seconds, push remote control
button once.
– Indicator LED will stop blinking and stay ON.
• Press remote control button again.
– Red LED will go out. Remote is now
programmed and ready for use.
1b. Multi Button Remote Programming.
NOTE: Each button on a multi-button remote is
designed for use with 1 door. You cannot program
2 buttons to operate the same door, nor can you
program 1 button to operate 2 doors. You can
program a maximum of 7 different transmitters or
wireless devices.
NOTE: Pushing two buttons on power head
simultaneously will erase programmed memory and
limits must be reset.
• For each button.
– Program each button separately using the
Single Button Remote Programming steps.
2. Operating.
• Press remote button once. Door will move.
• Press button again. Door will stop.
• Press button again. Door will move in opposite
direction.
NOTE: The door will stop automatically at the fully
open or fully closed position.
NOTE: To program a
Homelink® and Car2U®
device follow the Homelink®
or Car2U® instructions in your car owner's manual.
©2009 Overhead Door Corporation
WARNING
FOR HELP-1.800.929.3667 OR WWW.OVERHEADDOOR.COM
FCC and IC CERTIFIED
This device complies with FCC Part 15 and RSS 210 of
Industry Canada. This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which may be determined by turning the
equipment OFF and ON, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Re-orient or relocate the receiver antenna.
• Increase the separation between the opener and
receiver.
• Connect the opener into an outlet on a circuit
different from that to which the receiver is
connected.
• Consult your local dealer.
Limit Controls location
on power head.
LED
Indicator Light
To
Garage Door
Learn
Code
Button
FIG. 7-1 Learn code button and LED
LOST OR STOLEN REMOTE
1. Clear memory.
• Press and hold learn code button
head) for 10 seconds or until the red blinking
indicator LED goes out.
• Program remaining or new remote controls as
done previously. Your door opener will no longer
recognize any signal received from the missing
remote control, or any other which has not been
reprogrammed.
Part Number 37027500123 02/26/2010 REV. 1
Open
Open
Set Limit
Travel Limit
Button
SET
LEARN MANUAL LIMIT
SET
CODE
Close
Close
Set Limit
Travel Limit
Button
Up Force
Control
OPEN
Adjustment
FORCE
CLOSE
Down Force
Control
Adjustment
LEARN
(on power
CODE
21