Table of Contents
Advertisement
GARAGE DOOR OPENER SYSTEMS
108095
-0001
11 /07/
9
1
INSTALLATION INSTRUCTIONS
AND OWNERS MANUAL
READ THESE INSTRUCTIONS CAREFULLY BEFORE
INSTALLING OR USING THIS OPENER.
After
installation
is completed, place
instructions in
close
proximity to
garage
door.
All-American
Craftsmans
hip
Mode
in
U.S.A.
9111071330
Page
1
Advertisement
Table of Contents
Related Manuals for Overhead door 555
Summary of Contents for Overhead door 555
- Page 1 GARAGE DOOR OPENER SYSTEMS INSTALLATION INSTRUCTIONS AND OWNERS MANUAL READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR USING THIS OPENER. After installation is completed, place instructions in close proximity to garage door. All-American Craftsmans 108095 -0001 Mode U.S.A. Page 11 /07/ 9111071330...
-
Page 2: Tools Needed
TABLE OF CONTENTS TO USE TH IS BOOK GENERAL INSTALLATION NOTES PAGE ASSEMBLY DRAWING . . . • PAGE Use too ls indicated by si lhouettes at top of INSTALLATION INSTRUCTIONS PAGE instruction. W IRING INFORMATION PAGE 2. Perform t he instruction according to the words illustration. -
Page 3: Installation Notes
------------------------------------------------------ GENERAL INSTALLATION NOTES Preparing Door Opener The following procedures must be performed before opener can be installed. Failure to complete the follow- procedures can cause opener failure and/or hazardous conditions which could cause personal injury. Check working condition of door.Door should operate freely without sticking or binding, and should... -
Page 4: Assembly Drawing
ASSEMBLY DRAWING To complete assembly of your Overhead Door Operator: 1. Remove the four nuts securing the gear cover to the operator frame Removing the gear cover expose the drive sprocket. Slide the boom into the frame slot until it contacts the stop bolt. -
Page 5: Installation
INSTALLATION 2. D 1. D Measure width of door to determine center. Mark cen- Raise door until top section reaches highest arc of travel. Mark header tar line on door and header. center line point where level touches header. Mark horizontal center line of header bracket... - Page 6 7. D Manually raise door to a fully opened position If necessary, spacers between ladder opener to obtain clearance between.door and opener Rest header end of boom on edge of top door section (extension boom. spring door) or on torsion spring (torsion spring...
- Page 7 IT IS RECOMMENDED THAT OPENER BE MOUNTED A MINIMUM OF 7 FEET ABOVE FLOOR HOlCll ANGEL WITH 11nct:snw ·~ " " LENGTHWISE CEILING JOISTS DETAIL A ON CENTER CEILING LENGHf AS REQUIRED FRONT VIEW DETAIL B CROSSWISE CEILING JOISTS HOLES FRONT SLOT MAIN SUPPORT BRACING...
- Page 8 ,.., .. 0"' ) 1 7/16 If door strut interfers with mounting of Install door bracket on centerline of door as shown in step The pivot hole in door door bracket, move bracket below strut. bracket in line, close as possible, with the top ro ers of the doo Do not cut or modify door...
- Page 9 It is important that electrical power to operator off when powerhead cover removed. Electrical power must remain disconnected while making electrical connections and limit switch adjustments. Keep hand and objects clear of powerhead if electrical power is reconnected with cover off. Opener is equipped w tory in...
-
Page 10: Operation And Adjustments
OPERATION AND ADJUSTMENTS 20. D Plug opener power rd into elect ri cal outlet using wall button and adjust ope afety reverse syste as ou tlin tion opener and allow chai n cylind er engage opener c arriage. NOTE headed "OWNERS INFORMATION OPERATION/ADJUSTMENT". -
Page 11: Transmitter Visor Clip Mounting
OWNERS INFORMATION Transmitte~R~~::~~~p Mounting NOTE: This device complies with FCC rule part Operation this device is subject to the following two conditions: This device cause harmful interference. Attach transmitter visor clip This device must accept any interference that may shown. received, including interference that may cause undesired... -
Page 12: Multiple Security Code Entry Table
60 watt rough rvice Overhead Door bulb. To remove the obst tion . Two seve n fla shes indicate six more increased lens... -
Page 13: Troubleshooting
Repairs and adjustments should be Disconnect power to opener before opening cover. performed ONLY BY QUALIFIED OVERHEAD DOOR DISTRIBUTORS. The microprocessor does a self test when power connected to the In normal applications, lubrication... -
Page 14: Power Unit Ass Embly
POWER UNIT ASS EMBLY ILLUSTRATED PARTS BREAKDOWN Page 14... - Page 15 Protector Assemblv. Sur2e 080324-0006 Washer Lock Ext. 114" 080105-0406 Bolt HH 1/4-20 x 3/4" ' - J NOT SHOWN 555 WIRING SCHEMATIC PUSHBUTTON A COMMON VlOMti PHOTOCB.l LIGHT SECURITY ~,_t;~=~-ttt_J 24VOC « 11J1 ' - - - - - - --+-<...
-
Page 16: Limited Warranty
LIMITED WARRANTY Tho authorized distributor of Overheed Door Corporation products If Seller concludes that repair or replacement is necessary, Seller v.tlose name appears below ("Seller1 warrants this product to Wll commence work Wthin a reasonable time after the decision to repair or replace is made. be free from defects in materiel and v.orkmenship under nonnel end service.