Advertisement
Safety Instructions
trees and posts, on steps, garden paths and
patios, under bushes and hedges, on steep
slopes, in gaps between paving stones, etc.
C. Instructions regarding to safe handling
15. A power circuit breaker must be installed in
the power outlet to which the tool is connected
or on the electric cord to the tool. Contact an
electrician for further information. For a safe
operation, it is recommended to supply the
machine over a fault current safety breaker
(RCD) with a fault current not over 30 mA.
16. Before starting work check that your electric
tool is in good condition and that it is operating
properly. Pay special attention to the power
supply cord, extension cord, power outlet, switch
and cutting head.
17. Before using the machine, the line and
extension cords have to be checked for signs of
damage or ageing. Do not use the tool when the
cords are damaged or worn.
18. If the cord is damaged during utilisation, it must
be disconnected immediately from the mains.
DO NOT TOUCH THE CORD BEFORE IT IS
DISCONNECTED FROM THE MAINS.
19. Attention! Danger. The cutting head continues
to rotate after switch-off (flywheel effect). Keep
your fingers and feet well clear to avoid injury.
20. Use only extension cords that are approved
for outdoor applications and that comply with
specifications. Couplings and plugs must be
splashwater-proof. Never operate your tool
without a properly mounted and secured safety
cover. Check tightness of cutting head.
21. Do not use damaged power supply cords,
extension cords, couplings, plugs or cutting
heads.
22. Do not switch on the unit when hands or feet
are near the cutting elements.
23. Wear goggles or properly fitted safety
glasses, sturdy closed shoes with non-slip
soles, snugfitting work clothes, gloves and ear
protectors (ear plugs or ear mufflers).
24. Careless use can cause injuries to hand and
feet by the rotating cutting elements.
25. Always hold your tool firmly, if possible with
both hands - make sure you always maintain a
good balance and secure footing.
26. Work calmly and stay alert. Operate the tool
under good visibility and daylight conditions only.
27. Arrange the extension cord so that it cannot be
damaged and does not cause a hindrance.
28. Be careful not to chafe the extension cord
on corners, pointed or sharp objects. Do not
squeeze extension cord, e.g. through narrow
gaps in doors or windows.
29. Make sure the open side of the protection
guard is pointing away from yourself before you
switch on the tool.
30. Never tug the extension cord to disconnect the
plug. Always grip the plug.
31. Use particular caution while working in dense
growth areas where your view of the ground is
obscured.
32. Never leave your tool outdoors in rain.
33. Do not cut wet grass or other growth. Never
use in rain.
34. Hold the extension cord so that it is always
away from the rotating nylon line.
35. Transporting the electric tool, e.g. carrying it to
another site: Switch of the unit, disconnect the
plug.
36. Take special care in slippery conditions - on
slopes and uneven ground.
37. Work in a line across the slope and take special
care when turning around.
38. Watch for hidden obstacles such as tree tumps
and roots to avoid stumbling.
39. Clean the cutting head at regular intervals.
40. Check the condition of the cutting head
at requent intervals. If the behaviour of the
cutting head changes (vibration, noise), check
immediately as follows: Switch off the tool, hold it
firmly and bring the cutting head to a standstill by
pressing it against the ground. Then disconnect
plug from power supply. Check condition of
cutting head - look for cracks.
41. Be sure to bring the unit onto normal working
position before turning it on again.
42. Have a damaged cutting head replaced
immediately - even if it only has superficial
cracks. Never attempt to repair a damaged
cutting head.
43. Always switch off your tool and disconnect
it from the power supply before taking a
break and after finishing work. Do not forget
maintenance. (Plug disconnected!) Only carry
out maintenance and repairs described in these
operating instructions. Any other work should be
performed by your dealer. Do not grease - this is
unnecessary, as this unit has been pregreased
at the factory.
44. Inspect cooling air slots on the motor housing
at regular intervals for clog-ups and clean as
necessary.
7
Advertisement
