Installation - mabe PSS21 Series Service Manual

Use a cushioned hand truck to protect the
finished refrigerator. LEAVE
THE TAPE IN THE DOORS until it is in its
final location. LOAD ONLY FROM THE
SIDE. Avoid tighten the belt a lot to avoid
damage of the doors
CABL.
ALAMB.
METODO
PREFERIDO
ASEGURESE QUE EXISTE
ADECUADA PUESTA A
TIERRA ANTES DE USAR
ETODO TEMPORAL
(En Canadá no se permiten
daptadores de enchufe)
ASEGURE ADECUADA
PUESTA A TIERRA Y
CONEXION FIRME
ANTES DE USAR

Installation

Tape
REMOVE ALL THE PROTECTOR
TAPE FROM THE SURFACE, then
move the unit to its position. If the inlet
is less than 38" wide, remove the doors
before installation and reinstall them
according to the pro- bottom down.
•
HEET WAX IS RECOMMENDED TO REMOVE TAPE WASTE AND HAND FINGER FROM THE REFRIGERATOR OUTSIDE.
•
REMOVE ALL TAPE AND PACKAGING MATERIAL FROM INSIDE REFRIGERATOR. DO NOT REMOVE THE SERIAL PLATE.
•
REMOVE THE PROTECTIVE FILM ON THE TEMPERATURE CONTROL PANEL.
REMOVING THE DOORS
The doors must be in closed position.
Near the bottom hinge on the freezer side, tighten
the collar on the water line and pull the tubing from
the coupling. Also, disconnect the wiring from the
wire. Pull the water line and wiring through the
REBORDES
bottom rail.
CUBIERTA
Remove the covers of the upper hinges to access
BISAGRA
the hinges. Remove the hinges using a Torx T-20.
Carefully turn the door by 90 °. Guiding the water
line and wiring the fence, lift the door straight up.
PUERTA
Avoid loading the lower hinges sideways. Place the
doors on a protected surface. Avoid piercing the
water pipe and wiring the wiring in the bottom of the
SUJT.
BISAGRA door.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE ADEQUATELY GROUNDED
The power cord of this appliance is equipped with a three-prong (grounded) connector that fits a three-pronged (grounded)
standard receiver to minimize the risk of an electrical hazard to this appliance. The customer should check the wall receiver and
the circuit by a qualified electrician to make sure that the appliance is properly grounded.
Where a standard two-pronged wall receiver is located, it is the customer's responsibility and personal obligation to exchange it
for a properly grounded three-prong wall receptacle.
NDER NO CIRCUMSTANCES, CUT OR REMOVE THE THIRD POINT OF THE (EARTH) CONNECTOR FROM THE ENERGY
CORD. SITUATIONS OF USE IN WHICH THE ELECTRICAL CORD OF THE APPLIANCE WILL BE DISCONNECTED
INFRECTIVELY
Due to potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug. Without
em-
However, if you always choose to use an adapter where local codes permit, a TEMPORARY CONNECTION can be made to a
properly grounded two-prong wall receptacle approved by the UL adapter list which is available in most of the hardware stores.
The largest hole in the adapter must be aligned to give an appropriate polarity in the power cord connection.
to CAUTION: Connecting the terminal of the grounding adapter to the screw cover of the wall receiver does not ground
the device, unless the cover of the screw is made of metal, and is not insulated and the receiver of the wall is grounded through
the wiring of the house. The customer must check the circuit by a qualified electrician to make sure the receiver is properly
grounded. When disconnecting the power cord from the adapter, always hold the adapter with one hand. If you do not do this,
the terminal of the ground adapter is very safe to break with repeated use. If this happens, DO NOT use the appliance until a
ground connection has beenestablished
SITUATIONS OF USE IN WHICH THE ELECTRICAL CORD OF THE APPLIANCE WILL BE DISCONNECTED FREQUENTLY
Do not use an adapter plug in these situations because frequently disconnecting the power cord places undue stress on the
adapter and leads to eventual failure of the adapter terminal to ground. The customer must change the two-pronged receiver
on the wall for a receiver
Three-prong (grounded) by a qualified electrician before using the appliance.
AJUSTE ALTURA
RODILLO
AJUSTE AL-
TURA PUERTA
Connect the water lines and the electric
cord. ADJUST THE FRONT ROLLS so
that the refrigerator is firm on the floor
and the doors close easily. MAKE SURE
THE DOORS ARE COUPLES ABOVE.
REINSTALLING THE DOORS
With the doors open at 90 °, place them on the lower
hinge. Carefully turn the doors to the closed position.
Avoid loading the lower hinges sideways.
Reinstall the upper hinges and tighten the screws
firmly. Reinstall the hinge cover. If the doors are not
level, adjust the lower right hinges with a 7/16 open
end wrench.
Insert the water pipe back into the coupler. It is fully
connected when the mark on the pipe is no longer
visible. Reconnect the wiring of the wiring. Open the
water supply.
IMPORTANT: PLEASE READ CAREFULLY
- 3 -
CONTROLS ADJUSTMENTS
TEMPERATURE CONTROLS ARE
PRESCRIBED IN THE FACTORY
FOR RE-COMBUSED ADJUSTMENT
PUERTA
SUJET.
BISAGRA
CUBIERTA
BISAGRA
CABLEADO
ALAMB.
REBORD