Digital Equipment VAX 4000 Model 300 Installation Manual

Hide thumbs Also See for VAX 4000 Model 300:

Installation manual (96 pages)

Table Of Contents

Table of Contents

Table of Contents
Preface
Verify Site Preparation
Check the Shipment
Shipping Carton Contents
Position the System
Lock and Key Positions
Open the System Door
Opening the System Door
Install the Console Terminal
Perform Setup Operations
Connect the Console Terminal to the System
System Controls and Indicators-Power Switch
Set the System Controls
Setting Controls on the System Power Supply
Setting Controls on the Integrated Storage Elements (Ises)
Setting Controls on the System Control Panel (SCP)
Setting Controls on the Console Module
System Controls and Indicators-Integrated Storage Element, System Control Panel, and Console Module
System Controls and Indicators-Tape Drive
Setting Controls on the Tape Drives
Connect Additional Devices to the System
Connecting Terminals and Serial Printers
Connecting Devices to the Cable Concentrator
Mounting the Cable Concentrator
Connecting Parallel Printers to the System
Connecting Synchronous Modems to the System
Connecting Asynchronous Modems to the System
Connecting a Modem to a CXY08 Module
Connecting an Internal Modem to Telephone Lines
DFA01 Modem
- Telephone Service
Disconnecting the Telephone Line (Single-Line and Multiline Service)
Installing the Telephone Cord (Single-Line and Multiline Service)
Connecting a Modem to a Telephone (Single-Line and Multiline Service)
- Rj41S/Ca4La and RJ45S/CA45A Data-Jack Telephone Service
Connecting a Modem to a Wall-Mounted Jack (Data-Jack Service)-Telephone to Wall-Jack Connection
Connecting a Modem to a Wall-Mounted Jack (Data-Jack Service)-Telephone to DFA01 Connection
Setting up Terminal Lines
Connecting to an Ethernet Network at the Console Module
Ethernet Connector Switch on the Console Module
Making a Thin Wire Network Connection at the Console Module
- Making a Standard Network Connection at the Console Module
Making a Standard Ethernet Connection at the Console Module
Connecting to an Ethernet Network at the DESQA Module
- Making a Thin Wire Network Connection at the DESQA Module
Forming the Upper Cable in a Loop at the DESQA Module
- Making a Standard Network Connection at the DESQA Module
Connect an Expander, if Required
System Connections for Expanders
Connecting the Q-Bus Cables
Q-Bus Cables
DSSI Cable
Connecting the DSSI Cable
Tlz04Lrrd-Series External Cable
Removing the KZQSA Terminator
Connecting the Power Control Bus Cable
Power Control Bus Cable
Connecting the Ground Cable
Ground Cable
Connect the TLZ04 Internal Cable, if Required
Connect the DSSI Cable-Dual Host Only
Removing the DSSI Terminator
Connecting the DSSI Cable
Connecting the Ground Cable
Connect the Ground Cable-Dual Host Only
System Power Switch
Connect the System Power Cable
Power Cable Plugs
Connecting the Power Cable to the System
Turn on the System and Select a Language
Language Selection Menu
Successful Power-On Tests
Saving the Language
Close the System Door
Closing the System Door
After Installation
Appendix A Starting and Modifying VMS Factory-Installed Software
Pre-Startup Requirements
Startup Procedure
Modifying FIS for a Standalone System
Modifying FIS for a Simple Vaxcluster Network
Modifying FIS for a Complex Network or Dual-Host System
Configuring for a Dual-Host System
Checking Your Modification Work

Quick Links

Download this manual

VAX 4000 Model 300

Installation

Order Number: EK-335AB-IN-002

Table of Contents

Need help?

Do you have a question about the VAX 4000 Model 300 and is the answer not in the manual?

Digital Equipment VAX 4000 Model 300 Installation Manual

Quick Links

Need help?

Questions and answers

Related Products for Digital Equipment VAX 4000 Model 300

Digital Equipment VAX 4000 Model 300 Installation Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Digital Equipment VAX 4000 Model 300

Related Products for Digital Equipment VAX 4000 Model 300

Table of Contents