Page 1
ORDER NO. MD0501013C1 CD Stereo System SA-PM21PC Colour (S)... Silver Type Specification n Amplifier Section FTC Output Power both channel driven n Cassette Deck Section 10% total harmonic distortion Track system 4 track, 2 channel 15 W per channel (6 Ω) 20 Hz - 3.5 kHz (Low channel)
2. Total harmonic distortion is measured by the digital spectrum n General analyzer. Power supply AC 120 V, 60 Hz n System : SC-PM21PC-S Music center: SA-PM21PC-S Power consumption 57 W Speaker: SB-PM21E-MJ CONTENTS Page Page 1 Safety Precautions 10.19.
Page 3
SA-PM21PC 18.4. Deck Circuit, Deck Mechanism Circuit and Tape Eject 21 Illustration of IC 痴, Transistors and Diodes 22 Terminal Function of ICエs Circuit 18.5. Power Circuit 22.1. IC702 (MN6627953HB) Servo processor/ Digital signal 18.6. Transformer Circuit, Headphone Circuit and Speaker...
SA-PM21PC 1 Safety Precautions 1.1. GENERAL GUIDELINES 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, ensure that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Page 5
SA-PM21PC 1.1.3. Caution for fuse replacement...
SA-PM21PC 2 Before Repair and Adjustment Disconnect AC power, discharge Power Supply Capacitors C839 & C840 through a 10Ω, 1W resistor to ground. DO NOT SHORT-CIRCUIT DIRECTLY (with a screwdriver blade, for instance), as this may destroy solid state devices.
SA-PM21PC 5 Precaution of Laser Diode CAUTION: This unit utilizes a class 1 laser. Invisible laser radiation is emitted from the optical pickup lens. When the unit is turned on: 1. Do not look directly into the pick up lens.
SA-PM21PC 6 Handling Precautions For Traverse Deck The laser diode in the traverse deck (optical pickup) may break down due to potential difference caused by static electricity of clothes or human body. So, be careful of electrostatic breakdown during repair of the traverse deck (optical pickup).
SA-PM21PC 7 Accessories Note : Refer to Packing Materials & Accessories (Section 24.5) for part number. Remote control AC cord FM indoor antenna AM loop antenna...
SA-PM21PC 10 Assembling and Disassembling “ATTENTION SERVICER” Some chassis components may be have sharp edges. Be careful when disassembling and servicing. 1. This section describes procedures for checking the operation of the major printed circuit boards and replacing the main components.
SA-PM21PC Step 2 : Detach the connector CN803A, CN808A. Step 3 : Detach the connector CP800. Step 4 : Remove the Main P.C.B as arrow shown. Step 1 : Detach the connector CN805A and remove the tuner 10.11. Disassembly of Power P.C.B pack as arrow shown.
SA-PM21PC 10.14. Disassembly of CD Mechanism · Follow the (Step 1) - (Step 6) of Item 10.2. · Follow the (Step 1) - (Step 4) of Item 10.3. · Follow the (Step 1) - (Step 4) of Item 10.6. · Follow the (Step 1) - (Step 2) of Item 10.8.
SA-PM21PC 10.15. Checking Procedure for Each 10.16. Procedures of Replacing Major P.C.B. Traverse Base (Unit), Driving Gear, and Cam Gear (CD 10.15.1. Replacement of the Power Mechanism Unit) Amplifier IC · Replacement of the Power Amplifier IC 10.16.1. Disassembly of the Disc Tray.
SA-PM21PC 10.18. Procedures for Replacement Traverse Gear A and Traverse Gear B (CD Mechanism Unit) · Follow the (Step 1) - (Step 6) of Item 10.2. · Follow the (Step 1) - (Step 4) of Item 10.3. · Follow the (Step 1) - (Step 4) of Item 10.6.
SA-PM21PC · Follow the (Step 1) - (Step 4) of Item 10.4. 10.21. Procedure for Replacing Motor, Capstan Belt A, Capstan Belt B, and Winding Belt (Deck Mechanism Unit) · Follow the (Step 1) - (Step 6) of Item 10.2.
SA-PM21PC 10.22. Procedure for Replacing Parts on Deck Mechanism PCB · Follow the (Step 1) - (Step 6) of Item 10.2. · Follow the (Step 1) - (Step 4) of Item 10.3. · Follow the (Step 1) - (Step 4) of Item 10.4.
SA-PM21PC 11 Service Positions 11.1. Checking procedure Note: For the disassembling procedure, see the section 10. 11.2. Checking the major P.C.B. 1. Disassembly of Side Panel L & R Service tools Extension cable RFKPM21 2. Disassembly of Top Cabinet (Main P.C.B.
SA-PM21PC 12 Self Diagnostic Function 12.1. Self-diagnosis Function 12.1.1. Entering into self-diagnosis mode 1. Turn the power on. 2. Switch to CD mode with no CD or cassette loaded. 3. Press and hold the [STOPn] key of the main set for more than 2 seconds. While pressing this key, press the FF key on the main set for another 2 seconds to enter into the self-diagnosis mode.
Page 31
SA-PM21PC by the software. 5. After the tape stops, the Error codes will be displayed by toggling the STOPn key. For more detail explanation, refer to the (Figure 12-2). Figure 12-2 Operation Procedures Micon operation & processing C-mecha Abnormal Detection shall be Check that all DECK mechanism leaf SW are in OFF state.
SA-PM21PC Operation Procedures Micon operation & processing ] key is pressed, after loading a NORMAL, REW shall be executed for 2 sec, afterwhich STOP. CrO2, METAL type cassette with the recording Check the following. tab on the right side removed.
Page 33
SA-PM21PC 2. Press and hold [STOPn] button for at least 2 seconds, follow by [4] and [7] from the remote control. 3. When the Doctor Mode is activated the FL display will show the symbol at the 5 digit. At the same time, the micro-p’s version number (base 10) and EEPROM’s checksum (base 16) will be displayed for 1 sec.
Page 34
SA-PM21PC 3. After a few times, the FL shall display as below: Special Note: Due to certain reasons, when the following conditions occur, the aging will stop but the count value shall be maintained: · During OPEN operation, after a certain timing, the CD does not open in the Open position. (After REST SW is OFF, the CD OPEN SW did not turn ON after 4s.)
Page 35
SA-PM21PC 3. After a few times, the FL will display as shown below: Special Note : Due to certain reasons, when the following conditions occur, the aging will stop but the count value shall be maintained: · After 10s, the Disc Access has not yet complete.
Page 36
SA-PM21PC SW was not turned off in 4s.) · After 10s, the Disc Access has not yet complete. · Out of Focus for more than 2s. 12.4.5. Cold start setting (Note) In the case that you unplug from AC outlet after this mode was set, then plug to AC again, a cold start shall begin.
SA-PM21PC 13 Procedure for Checking Operation of Individual Parts of Deck Mechanism Unit 13.1. Operation Check with Cassette Tape 1. Pull up the EJECT lever using a rubber band. (Fig. 6) 2. Supply DC5V to MOTOR. (→ MOTOR rotates.) (Fig. 5) 3.
SA-PM21PC 14 Measurement And Adjustments 14.1. Cassette Deck Section 14.1.1. Requirements · Test tape (QZZCFM) (QZZCWAT) · Normal blank cassette tape (QZZCRA) · Digital frequency counter · Oscilloscope · Electrical voltmeter · Headphone jack output jig (Fig. 8) 14.1.2. Setting of Unit ·...
Page 40
SA-PM21PC Fig. 10 Fig. 11 14.1.5. Bias Voltage Check 1. Connect an electrical voltmeter. (Fig. 9) (Fig. 12) 2. Set the function to “TAPE” position. 3. Insert a normal blank cassette tape (QZZCRA). 4. While pressing and holding down [REC ( )] button, press [TAPE ( )] button to pause the recording mode.
SA-PM21PC 15 Voltage Measurement and Waveform Chart Note: · Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard. Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
SA-PM21PC 15.2. Waveform CN505B PIN 7 CN505B PIN 8 CN801 PIN 4 CN801 PIN 5 CD PLAY CD PLAY CD PLAY CD PLAY 20.6Vp-p (25msec.div) 21.4Vp-p (25msec.div) 3.64Vp-p (5msec.div) 3.36Vp-p (5msec.div) CN801 PIN 6 CN801 PIN 7 CN801 PIN 8...
Page 45
SA-PM21PC TO MAIN BLOCK BLK CK BLK CK CD SIGNAL OUTL NRST NRST OUTR STAT STAT SPOUT SPOUT SPPOL SPPOL (PC) MDATA MDATA TRVP TRVP MCLK MCLK IC702 MN6627953HB SERVO PROCESSOR DIGITAL SIGNAL PROCESSOR/ DIGITAL FILTER/ D/A CONVERTER X701...
Page 48
SA-PM21PC FL900 FROM FL DISPLAY TRANSFORMER TO CD BLOCK GRID1~GRID10 SEG1~SEG20 IC900 C0HBB0000044 IC802 FL DISPLAY C0DBZGC00067 3.3V REGULATOR Q802 Q801 SWITCH SWITCH D803 D804 IC803 MN101C49GHA MICROPROCESSOR...
Page 49
SA-PM21PC SIGNAL LINES : MAIN SIGNAL LINE CD SIGNAL LINE : TAPE PLAYBACK SIGNAL LINE : FM/AM SIGNAL LINE : TAPE RECORD SIGNAL LINE Note : Signal Lines are applicable to the Left Channel only. ) Indicates Pin No. of Right Channel...
SA-PM21PC 17 Notes of Schematic Diagram (All schematic diagrams may be modified at any time with the development of new technology) Note : S701 Reset switch S780 Open switch S900 CD switch S901 Tape switch S902 Tuner/Band switch S903 FF switch...
SA-PM21PC 18.2. Main Circuit and Tuner Extent Circuit : TAPE PLAYBACK SIGNAL LINE SCHEMATIC DIAGRAM-3 : TAPE RECORD SIGNAL LINE : CD SIGNAL LINE MAIN CIRCUIT : FM/AM SIGNAL LINE : +B SIGNAL LINE TUNER EXTENT CIRCUIT R201 6.8K CN805A...
Page 54
SA-PM21PC : MAIN SIGNAL LINE SCHEMATIC DIAGRAM-4 : TAPE PLAYBACK SIGNAL LINE : TAPE RECORD SIGNAL LINE MAIN CIRCUIT : CD SIGNAL LINE : +B SIGNAL LINE : FM/AM SIGNAL LINE R285 C281 C282 R801 2200P 1000P Q280 C890 16V100...
Page 55
SA-PM21PC SCHEMATIC DIAGRAM-5 : MAIN SIGNAL LINE MAIN CIRCUIT : CD SIGNAL LINE : +B SIGNAL LINE IC802 C0DBZGC00067 3.3V REGULATOR IC C804 C805 16V22 CD_LCH C216 L801 0.001 J0JKB0000020 CN801 CD_L C416 A_GND 0.001 CN808B HI_LEFT CD_RCH CD_R AGND CD_3.3V...
SA-PM21PC 18.4. Deck Circuit, Deck Mechanism Circuit and Tape Eject Circuit SCHEMATIC DIAGRAM-8 : TAPE PLAYBACK SIGNAL LINE DECK CIRCUIT : +B SIGNAL LINE : TAPE RECORD SIGNAL LINE C1105 470P R1103 C1122 0.01 R1101 C1104 0.027 C1102 C1101 470P...
SA-PM21PC 18.5. Power Circuit SCHEMATIC DIAGRAM-10 : -B SIGNAL LINE POWER CIRCUIT : +B SIGNAL LINE : MAIN SIGNAL LINE R350 2.2K IC300 AN17831A POWER AMP IC LOW R+ CN501A LOW R- C374 LOW L+ 50V100 LOW L- C373 C351...
SA-PM21PC 18.6. Transformer Circuit, Headphone Circuit and Speaker Terminal Circuit SCHEMATIC DIAGRAM-11 : - B SIGNAL LINE TRANSFORMER CIRCUIT : +B SIGNAL LINE : MAIN SIGNAL LINE POWER CIRCUIT (WH505A/JW505A) ON SCHEMATIC DIAGRAM-10 CN505B Q603 2SB0621AHA -VP VOLTAGE REGULATOR CN900B...
SA-PM21PC 22 Terminal Function of IC´s 22.1. IC702 (MN6627953HB) Servo Pin No. Mark Function RFOUT RF Amp output processor/ Digital signal RFIN AGC input processor/ Digital filter/ D/A CAGC AGC control terminal ARFOUT AGC output (Audio RF) converter AVSS2 Analog circuit GND 2...
SA-PM21PC 22.2. IC703 (BA5948FPE2) IC 4CH DRIVE Pin No. Mark I/O Function Pin No. Mark I/O Function Motor Driver Input Motor Driver (3) reverse - action output Turntable Motor Drive Signal (“L”: ON) Motor Driver (3) forward - action output...
SA-PM21PC 24 Parts Location and Replacement Parts List Notes: · Important safety notice: Components identified by mark have special characteristics important for safety. Furthermore, special parts which have purposes of fire-retardent (resistors), high-quality sound (capacitors), low noise (resistors), etc are used.
SA-PM21PC 24.1. Deck Mechanism 24.1.1. Deck Mechanism Parts Location (RAA4402-S)
Page 80
SA-PM21PC 24.1.2. Deck Mechanism Parts List Ref. No. Part No. Part Name & Description Remarks CASSETTE DECK RED0067 R/P HEAD BLOCK UNIT RDG0300 REEL BASE GEAR RDG0301 WINDING RELAY GEAR RDK0026 MAIN GEAR RDV0033-4 WINDING BELT RDV0064 CAPSTAN BELT RMB0312...
Page 85
SA-PM21PC 24.3.2. Cabinet Parts List Ref. No. Part No. Part Name & Description Remarks CABINET AND CHASSIS RDG0357 DAMPER GEAR REEV0033 12P FFC (PANEL-MAIN) REEV0034 17P FFC (MAIN-CR120) REEV0035 19P (DECK-MAIN) RGKV0087-S CD LID RGLV0045-Q LIGHTING TIP RGUV0102-S MP3 CTRL BUTTON...
SA-PM21PC 24.4. Electrical Part List Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks PRINTED CIRCUIT BOARD D380 B0AACK000004 DIODE REPV0016A DECK P.C.B. / TAPE EJECT D501 B0EAMM000038 DIODE P.C.B. (RTL)
Page 87
SA-PM21PC Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks CN503B K1KB09B00013 9P CONNECTOR CN504A K1MP04A00003 4P CONNECTOR FP352 K5G502A00039 FUSE PROTECTOR CN505B RJT119W08V 8P CONNECTOR FP552 K5G202A00025 FUSE PROTECTOR CN508A...
Page 88
SA-PM21PC Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks R483 ERJ6GEYJ473V 47K 1/10W R751 ERJ3GEYJ102V 1K 1/16W R484 ERJ6GEYJ472V 4.7K 1/10W R752 D0GB222JA041 2.2K 1/16W R485 ERJ6GEYJ273V 27K 1/10W R753...
Page 89
SA-PM21PC Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks R869 ERJ3GEYJ102V 1K 1/16W R1329 D0GB472JA041 4.7K 1/16W R870 ERJ3GEYJ102V 1K 1/16W R1330 ERD2FCVJ4R7T 4.7 1/4W R871 ERJ3GEYJ102V 1K 1/16W R1331 ERJ3GEYJ752V 7.5K 1/16W...
Page 90
SA-PM21PC Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks C221 F1H1H331A013 330P 50V C582 ECA1HAK010XB 1 50V C222 ECJ1VC1H101J 100P 50V C586 ECA1HAK100XB 10 50V C223 ECJ1VC1H101J 100P 50V C601 F1B1H103A153 0.01 50V...
Page 91
SA-PM21PC Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks C823 ECJ1VB1H472K 4700P 50V C1308 ECA1CAK220XB 22 16V C824 ECJ1VB1H472K 4700P 50V C1310 ECA1HAK0R1XB 0.1 50V C825 ECJ1VB1H472K 4700P 50V C1311...
SA-PM21PC 24.5. Packaging Materials & Accessories Parts List Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks PACKING MATERIALS N2QAJB000131 REMOTE CONTROL RPGV0169 PACKING CASE A1-1 RKK-HTR0051K R/C BATTERY COVER RPNV0062...