Advertisement
Quick Links
Ethernet/PoE Extender over UTP Cable Installation Guide
Product Overview:
1. Extend: RJ45 Female Connector (No LED) converter allows 10/100 Base-T Ethernet and PoE power to be
transmitted using Cat. 5 or better UTP cable with 4 pair wires.
2. Link: The LED indicates the cable link status. The LED will be on after 10 seconds when first connection is
success; Off: No connection.
3. Pwr: The LED indicates the power status. On: Power on; Off: No power.
4. Ethernet/PoE: RJ45 connector, attaches to POE IP Camera or Hub via Cat5, 5e, 6 or 7 patch cables.
5. Eth: The LED indicates the communication status. Flash: Communicate with Traffic; Off: No connection.
6. Power jack: Plug DC power adapter to for PoE source when PoE Hub cannot provide enough power source.
7. PoE: The LED indicates the PoE power status. On: PoE power is provided; Off: No PoE power.
1
Packing Checklist:
Check the package box the following items are included:
EPOC-131VAJ (Or EOPC-131PSJ) * 1 ea;
Menu * 1 pc.
Installation Steps:
IP camera end
1. Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port of EPOC-131PSJ using a standard
Cat5/6 cable of maximum 100 m (328 feet) in length.
2. Connect one end of the long UTP cable such as Cat.5, 5e, 6, or 7 cable to the RJ45 (No light) connector of
EPOC-131PSJ.
3. When the IP camera and EPOC-131PSJ cannot receive power through the UTP cable, even through using the
POE+ Hub or plug DC56V power adapter for EPOC-131VAJ. Plug the DC48V power adapter into the
EPOC-131PSJ will be needed at this end. Please refer to "Power Distance VS. Cable Impedance" table.
Switch Hub end
1. Connect the PoE switch Hub RJ45 connector to the 10/100BaseT Ethernet port of EPOC-131VAJ using a
standard Cat5/6 cable of maximum 100 m (328 feet) in length.
2. Connect one end of the long UTP cable such as Cat.5, 5e, 6, or 7 cable to the RJ45 (No light) of EPOC-131VAJ.
3. When the IP camera and EPOC-131PSJ cannot receive power through the Wire cable, please change the POE+
Hub or plug DC56V power adapter to EPOC-131VAJ.
2
3
4
5
6
1
1
7
2
5
3
4
V1.2
6
Advertisement
Related Manuals for I-View EPOC-131VAJ
Summary of Contents for I-View EPOC-131VAJ
-
Page 1: Product Overview
Cat5/6 cable of maximum 100 m (328 feet) in length. 2. Connect one end of the long UTP cable such as Cat.5, 5e, 6, or 7 cable to the RJ45 (No light) of EPOC-131VAJ. 3. When the IP camera and EPOC-131PSJ cannot receive power through the Wire cable, please change the POE+... -
Page 2: Product Application Diagram
Connector for Ethernet/PoE signal transmission when there are more 16 pcs EPOC-131VAJ install at the same Hub site. Daisy Chain Plug DC56V power adapter to EPOC-131VAJ or DC48V to EPOC-131PSJ when the IP Camera cannot receive Point to Point Topology Plug DC48V power adapter to EPOC-131PSJ when the EPOC-131PSJ cannot receive power. - Page 3 Power Wattage VS. Cable Distance Data Rate VS. Cable distance LED Function table Name Color Status Function Yellow Power is on Power is off Green Flashing Communication is OK with Traffic No communication Link Green Connection is OK; (It take 10 sec. for LED on) No connection Green PoE is offering...
-
Page 4: Specification
Specification: ITEM \ MODEL EPOC-131VAJ EPOC-131PSJ EPOC-131PSJ-O Ethernet Connector RJ-45 RJ-45 RJ-45 Connectivity 10/100/1000 Base-T auto-negotiation, auto MDI / MDX crossover Wire type Cat5 or better Distance Up to 328 feet (100m) Cable Link Connector RJ-45 Type Receiver (Hub Site) - Page 5 Mail: support@i-view.com.tw...