ABB HS/S4.2.1 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Accessories
  5. HS/S4.2.1
  6. Installation and operating instructions manual

ABB HS/S4.2.1 Installation And Operating Instructions Manual

Brightness sensor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
HS/S4.2.1
Brightness sensor
2CDG120044R0011
Installation and

operating instructions

D GB
F
I
S
NL
C1
C5
C2
C6
C3
C7
C4
C8
DA
TA
Sensorwerte
L1 Sensor Ost
528 lx
L2 Sensor Süd
505 lx
L3 Sensor West
883 lx
MENU
OK
Set Phys Adr
2
0,5mm -
L
N
110-240V~
2
2,5mm
50-60Hz
HS/S4.2.1
µ
µ
4
5
10
11
6
12
C2
C4
309597 01
GB
L
N

Advertisement

Table of Contents
loading

Related Manuals for ABB HS/S4.2.1

Summary of Contents for ABB HS/S4.2.1

  • Page 1: Operating Instructions

    309597 01 HS/S4.2.1 Brightness sensor 2CDG120044R0011 Installation and operating instructions Sensorwerte L1 Sensor Ost 528 lx L2 Sensor Süd 505 lx D GB L3 Sensor West 883 lx MENU Set Phys Adr 0,5mm - 110-240V~ 2,5mm 50-60Hz HS/S4.2.1 µ µ...

  • Page 2: Table Of Contents

    Contents Basic safety instructions Display and keys Connection/installation Bus connection, programming physical address Start-up 7 Home page – Sensor values Enter PIN Menu – Settings.. Language.. Display.. System.. Sensors.. Deactivate active sensor Allocate new serial number to active sensor Menu – Switching channels.. Select light threshold (brightness) Select delay Technical date...

  • Page 3: Basic Safety Instructions

    Basic safety instructions WARNING Danger of death through electric shock or fire!  Installation should only be carried out by a professional electrician! • The device is designed for installation on DIN top hat rails (in accordance with EN 60715); device conforms with EN 60669-1 •...

  • Page 4: Display And Keys

    Screen and keys Connection/installation Screen display, Sensorwerte L1 Sensor Ost e. g. sensor values 528 lx L2 Sensor Süd 505 lx L3 Sensor West 883 lx ? MENU MENU Data – Activate screen – Open menu Set Phys Adr – Cancel menu ...

  • Page 5: Connection/Installation

    Connection/installation WARNING Danger of death through electric shock!  Must only be installed by professional electrician!  Disconnect power source!  Cover or shield any adjacent live components.  Ensure device cannot be switched again! 45° cable  Check power supply is disconnected! Spring terminal ...

  • Page 6: Bus Connection, Programming Physical Address

    Bus connection Program physical address  Insert bus line in the front of the device.  Press button on front of the device.  Ensure correct polarity. à The programming LED lights up. à Device is in program mode. MENU Start-up, diagnostics and configuration are Set Phys Adr Push button...

  • Page 7: Start-Up

    Start-up The pages displayed depends on the programming by the ETS. Please refer to the Product Handbook for detailed functional descriptions (at www.abb.com/knx). Home page – Sensor values Sensor values If an external sensor is connected, the sensor value (lux value) No sensors appears on screen.

  • Page 8: Menu - Settings

    Menu – Settings.. Menu Settings .. K1 :Switching channel 1.. K2 :Switching channel 2.. The Settings menu item can be used for setting the language, K3 :Switching channel 3.. K4 :Switching channel 4.. Back screen lighting or information on the device and sensors. MENU Press MENU button.

  • Page 9: Language

    Settings– Set language Language  Use to select language. Deutsch English Francais  Press OK to confirm. Espanol Italiano  Use to select desired language. Nederlands MENU Settings– Set display Display  Use to select display. Light keypress  Press OK to confirm. Back MENU...

  • Page 10: System

    Settings – System.. System  Use to select system. Prog. mode 15.15.255 VI.0  Press OK to confirm. SN: 0048112233445566 11.11.2011 MENU The display shows Prog. mode (Programming mode) PA (Physical address) SW (Software version) SN (Serial number) FD (Finishing date) HW (Hardware)

  • Page 11: Sensors

    Settings – Sensors..  Use to select sensors. Process sensors L1 sensor 1 SN: 123456789  Confirm by pressing OK. L2 sensor 2 inactive L3 sensor 3 Error Back The Sensors menu item can be used to display the lux values MENU for up to 3 connected sensors.

  • Page 12: Allocate New Serial Number To Active Sensor

    Allocate new serial number to inactive sensor  Use to select Next serial number. L1 sensor 1 inactive  Press OK to confirm. Next serial number Allocate Back The inactive sensor displays a new SN number. MENU  Use to select Allocate.  Press OK to confirm and, if reqd., select Back to leave menu.

  • Page 13: Menu - Switching Channels

    Menu – Switching channels.. Menu Settings .. K1 :Switching channel 1.. K2 :Switching channel 2.. The Switching channels menu item displays the status of the K3 :Switching channel 3.. K4 :Switching channel 4.. Back channel (ON, OFF, disabled/invalid): MENU Press MENU button. ...

  • Page 14: Select Light Threshold (Brightness)

    Select light thresholds (brightness) The Light thresholds menu item can be used to set of the K1 :Switching channel 1.. Status: brightness of the relevant channel: Light thresholds.. Next channel Back.. to select Light thresholds. MENU  Press OK to confirm. ...

  • Page 15: Select Delay

    Select delay The Delay menu item can be used to set the delay time: K1 :Delay Exceed 15 s Underrun 90 s to select Delay.  Back.. Press OK to confirm. MENU  to select Exceed or Underrun.  Press OK to confirm selection. ...

  • Page 16: Technical Data

    • Protection class: II subject to correct installation Service address • Protection rating: IP 20 in accordance with EN 60529 ABB STOTZ-KONTAKT GmbH • Pollution level: Eppelheimer Straße 82 69123 Heidelberg • Max. cable cross section: 2.5 mm Germany • Operating voltage KNX: bus voltage ≤10 mA Tel.

Table of Contents