Advertisement
Quick Links
Safety information
Roxtec recommends that all installations
are performed without facility operation.
Follow national regulations and installation
codes. Any action affecting the routed
service should be performed according to
manufacturer recommendations.
Components
Stayplate
HD 32 frame
including gasket
Roxtec CM BG™ B modules
Measures in millimeters (mm)
Module size
CM 20 BG B
CM 20w40 BG B
CM 30w40 BG B
CM 40 10-32 BG B
CM 40 BG B
Note:
The range of the modules indicates the smallest diameter of the exposed cable armor to the largest diameter of the cable
jacket. Modules with core can be used as spare parts.
CM BG B modules
Counterframe
For cable outer diameter
min-max
4-14.5
3.5-16.5
10-25
9.5-32.5
21.5-34.5
Installation instructions
Roxtec HD 32 with
CM BG
Compression unit
C Wedge HD AISI 316
Nuts
Roxtec CM BG™ B solid modules
Module size
CM 10w40/0 BG B
CM 20/0 BG B
CM 40/0 BG B
B modules
™
Roxtec Lubricant
Fasteners for protective
bonding conductor
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Roxtec CM BG B Series
Summary of Contents for Roxtec CM BG B Series
-
Page 1: Safety Information
C Wedge HD AISI 316 HD 32 frame Counterframe Nuts Fasteners for protective including gasket bonding conductor Roxtec CM BG™ B solid modules Roxtec CM BG™ B modules Measures in millimeters (mm) Module size For cable outer diameter Module size min-max... -
Page 2: Aperture Dimensions
Roxtec CM BG™ B module A: Environmental side E: Module braid B: Termination/interior side F: Cable jacket C: Removable layers D: Cable armor Aperture dimensions Packing space Max wall/cabinet thickness: 4 mm R3 (4x) CM 20w40 BG B CM 20w40 BG B... -
Page 3: Installation
Remove the outer jacket and any armor. Suggestions for cable a CM BG B module. The cable braid. plastic foil. The cable armor shall preparations are available on armor shall be visible outside the be clean and conductive. www.roxtec.com. module. - Page 4 Lubricate the sealing surfaces Lubricate the sealing surfaces Lubricate the sealing surfaces of differ (A) by more than one of all modules with Roxtec of the spare modules. Do not the solid modules. between the corresponding Lubricant. Avoid excess lubricant remove the core.
- Page 5 Place corresponding termination side. termination side. module halves on top. Use a Roxtec pre-compression Before inserting the final module, Lift up the stayplate and insert Drop the stayplate on top of tool to make space for the insert a stayplate.
- Page 6 Tighten the screws of the Visible excess lubricant is a sign If applicable, check that the Verify earth continuity from each compression units alternately of good compression. Make protective bonding conductor is cable armor to the earthing until full stop, approx. 20 Nm. sure that all modules are placed correctly installed.
- Page 7 Disassembly and reinstallation Untighten the screws of the Remove the compression units. Lift up the stayplate and push Remove the stayplate. compression units and push out the first module from the them. front side. Continue to remove the modules The inside surfaces of the Lubricate the inside surfaces, by pulling them out from the exposed packing space shall be...
- Page 8 The Roxtec system has been certified to resist a number of different Roxtec gives no guarantee for the Roxtec system or any part thereof and as- hazards. Any such certification, and the ability of the Roxtec system to resist...
Need help?
Do you have a question about the CM BG B Series and is the answer not in the manual?
Questions and answers