1. Manuals
  2. Brands
  3. HydroHoist Manuals
  4. Boating Equipment
  5. HydroPort EXTREME
  6. Installation manual

HydroHoist HydroPort EXTREME Installation Manual

Hide thumbs Also See for HydroPort EXTREME:
Table of Contents

Advertisement

Quick Links

INSTALLATION
MANUAL
HydroPort
EXTREME
®
915 W. Blue Starr Dr. Claremore, OK 74017
(918)341-6811
2003268 Rev D

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HydroPort EXTREME and is the answer not in the manual?

Questions and answers

Related Manuals for HydroHoist HydroPort EXTREME

Summary of Contents for HydroHoist HydroPort EXTREME

  • Page 1 INSTALLATION MANUAL HydroPort EXTREME ® 915 W. Blue Starr Dr. Claremore, OK 74017 (918)341-6811 2003268 Rev D...

  • Page 2: Safety Notice

    AC GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEVICE WHICH IS TO BE USED IN SERIES WITH THE USER’S PRIMARY AC POWER SOURCE. THE GFCI IS AN INTEGRAL PART OF THE HYDROHOIST BOAT LIFT AND IS DESIGNED TO OFFER A LIMITED MEASURE OF PROTECTION TO THE USER AGAINST HAZARDOUS ELECTRICAL CONDITIONS OR SHOCKS SHOULD THEY OCCUR.
  • Page 3 ® HydroHoist Marine Group ® ® Model: HydroPort Extreme CONTENTS Getting Started - Section 1 Assembly - Section 2 Installation - Section 3 Operating Instructions - Section 4 Trouble Shooting - Section 5 Parts List - Section 6...

  • Page 4: Getting Started

    Getting Started ® HydroHoist Marine Group ® ® Model: HydroPort Extreme Sec. 1 Pg. 1 Getting Started Assembly Platform Assembly can be performed on land, trailer, or water. Tools A list of tools needed for hoist assembly is given below. In addition to these, tools for boat dock preparation, dock bumper removal, etc.
  • Page 5 Assembly ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 2 Pg. 1 Assembly Instructions Notes: Steps 1.1-1.3 are completed on purchased unit. Procedure Step Insert the Bow Bumper [2] into the Main Body. Place washer [3] on shoulder bolt [4] and insert through bow stop [2] for all four locations.

  • Page 6: Installation Instructions

    Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 1 Installation Instructions Floating Dock Step Procedure Insert mooring plug [2] into mooring cavity in port body [1]. Hook mooring bracket [3] into the recess in the bottom of the platform body [1]. Pivot the bracket up against the port body.
  • Page 7 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 2 Installation Instructions Fixed Dock / Wall Step Procedure Insert mooring plug [2] into mooring cavity in port body [1]. Hook mooring bracket [3] into the recess in the bottom of the platform body [1]. Pivot the bracket up against the port body.
  • Page 8 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 3 Installation Instructions Floating Dock Step Procedure Drill four 3/8” holes into dock face and attach the Extended Hinge Mooring Plate [1]. If using the HD Dock Brack- et [3] with the Hinge Mooring Plate, holes will only need to be drilled if using thru-bolt method (Fig.
  • Page 9 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 4 Installation Instructions Side Mount (Floating shown) Step Procedure When attaching the Floating Mooring Bracket for side-mounted application remove the mooring cap plugs from the side that the mooring will be attached to. Reinstall the mooring cap plugs into the front mount mooring plug cavities.
  • Page 10 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 5 Installation Instructions Fixed Dock \ Wall Installation Step Procedure Attach the Universal Dock Bracket [1] to the dock as shown (3 different methods are illustrated). NOTE: IT IS UP TO THE INSTALLER TO DETERMINE IF THE ATTACHMENT IS STRONG ENOUGH.
  • Page 11 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 6 Installation Instructions Connecting Units Step Procedure Assemble parts as shown below. The front shows how the links will appear when installed, the rear shows the links assembled for installation. The top and bottom links are connected by the long bolt but not tightened.
  • Page 12 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 7 Installation Instructions Connecting Units Step Procedure Float the second port over to the port with the connecting links, pull the top plugs up just enough to clear the top of the port.
  • Page 13 Installation ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 3 Pg. 8 Strap Hook Installation NOTE: Fig R. TEMPORARY ATTACHMENT CUSTOMER IS RESPONSIBLE FOR PROVIDING SECURE ATTACHMENT.

  • Page 14: Operating Instructions

    Operating Instructions ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 4 Pg. 1 Operating Instructions Loading ( ® WARNING Only load PWC when HP EXTREME is unoccupied 1. Approach HP EXTREME at idle speed only. 2. Position bow of PWC between entry rollers as centered as possible.

  • Page 15: Troubleshooting

    ® Trouble Shooting HydroHoist Marine Group ® ® Sec. 5 Pg. 1 Model: HYDROPORT EXTREME Trouble Shooting CONDITION: I can’t get my PWC to stay on the HP EXTREME when I pull on to the platform A.) Coming in too fast POSSIBLE CAUSE: B.) The PWC’s weight is to far too the rear of the craft.

  • Page 16: Parts List

    Parts List ® HydroHoist Marine Group ® ® Model: HYDROPORT EXTREME Sec. 6 Pg. 1 Parts List Part # Qty. Part # Qty. Floating Mooring (4154025) Fixed Mooring (4154027) Nut - Hex - 3/8" Galv 2090107 Fixed Mooring 4154018 Nut - Hex - 1/2" Galv 2090111 Bolt - Hex Head - 1/2"...

Table of Contents

Save PDF