Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EcoStar and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SEFAM EcoStar

  • Page 2: Table Of Contents

    Transport and storage conditions ..................16 Physical characteristics ......................16 Electrical characteristics of the power supply module ............17 Standards Compliance ......................17 Disposing of the device at the end of its life ................ 17 CE marking ..........................17 2  Table of Contents EcoStar...
  • Page 3: Before Starting

    Avoid covering the device or Only use the EcoStar device for its intended  placing it too close to a wall. Do not introduce purpose indicated in this manual. The advice liquids or objects into the air outlet.
  • Page 4: Intended Use

     Place the heating humidifier and the EcoStar  Decompensated cardiac insufficiency or device on a flat, stable surface and keep them hypotension, particularly in case of away from sources of flames.
  • Page 5: Description Of The Device

    Description of the device The EcoStar device is powered by an external electrical power supply module and comes with specific accessories Views of the Device Figure 1 View of the user interface Display this allows viewing information such as the pressure delivered and the device settings.
  • Page 6: Symbols On The Device

    Direct current power supply. Direct current. Specific warning (see "Safety Refer to the user manual. instructions" on page 3). Device complies with the requirements of European Directive Keep dry. 93/42/EC on medical devices. 6  Description of the device EcoStar...
  • Page 7: Installation

    Installation for use with battery or cigar lighter power The EcoStar device can be powered by a 12- Volt battery by connecting one end of the specific optional cable to the supply 2. Prepare the mask as described in the...
  • Page 8: Use

    Following a power supply interruption, the device chamber before moving or transporting the will resume the same mode it was in (on/off) before assembly, to eliminate any risk of introducing the disconnection. water into the device and thereby causing irreversible damage. 8  Use EcoStar...
  • Page 9: Ramp Feature

    To do that, refer to the "Device is on or off, as well as the nature of the setting" paragraph on page 10. parameter displayed (see table entitled "Description of symbols displayed on the screen" on page 10). EcoStar Use  9...
  • Page 10 Exiting the parameter setting menus happens automatically if you do not press any buttons for 30 seconds.  In the information access sequence below, the device is shown in operating mode and all the values displayed are given by way of example. 10  Use EcoStar...
  • Page 11 Pd or actual pressure Pr (estimated at the mask). The selection is done by pressing the button ❼ Software version included with the device. Press The version number is indicated by two digits (); for example, the screen might display: Id 1.0. EcoStar Use  11...
  • Page 12: Use With Added Oxygen (Optional)

    EcoStar device. accumulate inside the device, creating a 2. Likewise, you must stop the oxygen flow fire hazard.
  • Page 13: Cleaning And Maintenance

    Do not use detergent sprays. Chemical  product residue could enter the air outlet, the filter's foam or the device interior, causing airway irritation.  Never use the device without making sure that an air inlet filter is installed. EcoStar Cleaning and Maintenance  13...
  • Page 14: Trouble-Shooting

    The device does not The ramp is enabled. Confirm that the ramp indicator is displayed. display the correct Disable the ramp feature by pressing the pressure. ramp button. 14  Trouble-shooting EcoStar...
  • Page 15: Device Messages

    Check the battery and replace it if necessary. If the message persists, contact your home care provider. Er XX The device has detected Contact your home care provider. (XX = 2 digits). an operating fault. EcoStar Trouble-shooting  15...
  • Page 16: Technical Characteristics

    500 hPa to 1060 hPa excluding the power supply module Temperature: -20°C to +60°C Weight: 0.644 kg approximately (-4 °F to +140 °F) (1.4 lbs approx.), excluding Relative humidity: up to 95% without the power supply module condensation 16  Technical characteristics EcoStar...
  • Page 17: Electrical Characteristics Of The Power Supply Module

    2012/19/EC this device is an electrical standard, specifically with reference to global residual and electronic piece of equipment and risk. The EcoStar device complies with the following must be collected and processed directives and standards: separately from household waste for disposal.
  • Page 18 18  Technical characteristics EcoStar...
  • Page 20 Home care Provider Information Manufacturer: Manufacturing plant: SEFAM SEFAM 144 AV CHARLES DE GAULLE 10 ALLEE PELLETIER DOISY 92200 NEUILLY SUR SEINE 54600 VILLERS-LES-NANCY FRANCE FRANCE : M-159DFU00-20 Version 6 2019-01...

Table of Contents