Advertisement
Illustration 1e - Front-Center Drain, Unit Dimension & Alcove Framing Guidelines (dimensional tolerance +0 / -3/8")
04
Drain
Center
02
Minimum
Alcove Depth,
Unit Rough-In
Depth
Model
01
TR(G)-S/IF-900*
60"
s
OV-S/IF-320*
72"
s
*Standard 'S' model includes a removable apron access panel
Whirlpool equipped 'S' model includes a removable apron access panel
s
by the flanges at each end, then down
the front vertical flanges. Use 1-1/4" large
headed nails or screws. Continously check
to confirm the unit remains square within the
alcove as it is being secured (illust. 3 & 4).
NOTE: It is advisable to protect the unit sur-
face with a thin plywood or cardboard shield
while fastening the flanges to the framing
(illust. 5).
WARNING!
THE INSIDE UNIT SURFACE SHOULD
BE CLEAR OF ALL LOOSE DEBRIS
AND THE SURFACE PROTECTED
BEFORE STEPPING INSIDE.
Illustration 2 -
Unit Installation
Procedure
Wall
Framing
Nailing
Flange
1. Position Tub
in Framed Area.
03
Finished
07
Unit Depth
21" Wide
Whirlpool
Drain
Pump
5"
Cut-Out
Access
08
5"
06a
06b
05a
05b
01
Alcove Length - Unit Width
02
03
04
43"
41-3/4"
29"
43-1/4"
42"
33-3/4"
Removable Apron Panel
Certain aproned models come standard with
a removable apron panel, while most mod-
els include a removable apron panel when a
whirlpool or air system is ordered. Refer to
your specific model for included features.
Oasis models with a removable apron
system incorporate 4-6 adjustable magnet
assemblies for quick and secure panel
removal and reattachment.
The following procedure is recommended
for the careful removal of the apron panel.
1. Grasp the bottom of the apron panel
edge with both hands and pull away from
the unit. This will release the bottom
Confirm Drain Alignment
Confirm unit apron is
flush on floor.
Fixture
Blocks
05a
05b
06a
30"
30"
27-1/2" 27-1/2" 26-1/2" 10-1/4"
36"
36"
33-1/2" 33-1/2" 31-1/4"
Nailing Flange
Whirlpool Access
Front Drain Cut-Out
06b
07
08
5-3/4"
magnets while the panel top remains at
rest on the upper row of magnets (illust. 7).
2. Pull the panel completely away from the
top magnets and safely store the panel
out of the way to avoid damage.
To reattach the panel:
1. Locate the 'up' arrow on the inside of
the panel and rotate it to the correct
position for reassembly.
2. Holding the panel at the top with the fin-
ished side facing you, locate the magnet
alignment edges of the two outside re-
ceiver plates with your fingers. Angle the
panel top in toward the unit apron and
attach the receiver plates to the outside
magnets, ensuring the alignment edge is
above the top of the magnet (illust. 8).
3. Once the top of the panel is aligned,
complete the attachment by pushing the
bottom of the panel against the lower
magnet assemblies until they catch.
4. In the event that the reattachment does
not line up, simply remove the panel
(steps 1 & 2 for panel removal) and
repeat the attachment.
Removable Panel Adjustments
Hand adjustments can be made to the
removable apron attachment system should
they become necessary. Simply move the
magnets in or out by turning in either direc-
tion (illust. 9). Reattach the panel to check
for a correct fit and readjust the magnets if
necessary
5
Advertisement
