Advertisement
Quick Links
AHKD SERIES
ELECTRIC RESISTANCE HEAT KITS
INSTALLATION INSTRUCTIONS
I
NTRODUCTION
Product Description
The AHKD series of electric heat kits is an accessory designed for
installation with the Daikin DAR0904 or DAR1204 Airhandler ONLY.
INSTALLATIONS WITH OTHER AIRHANDLERS IS NOT PERMITTED.
For installation guidelines of the DAR0904 or DAR1204, refer to
the instructions which accompany the air handler, IOD-4010 (In-
stallation & Operating Instructions).
The AHKD provides supplemental electric heat for the DAR0904/
1204. The assembly is to be installed directly to the outlet of the
DAR0904/1204 and is not to be used as an independent duct
heater.
The AHKD20 and AHKD30 heat kits have two stages. A two stage
room thermostat determines the staging by room temperature.
The heat kit's control panel is "self contained" and is equipped
with all of the safety circuit/limits required per UL1995. The heat
kit employs a terminal block for installation of the high voltage
wires used by both the heat kit and the airhandler (single point
wiring).
C
P
R
HECKING
RODUCT
Upon receiving the unit, inspect it for damage from shipment.
Claims for damage, either shipping or concealed, should be filed
immediately with the shipping company. Do not install this acces-
sory if it is determined that the integrity or safety has been com-
promised by freight damage.
ECEIVED
© 2013
5151 San Felipe, Suite 500, Houston, TX 77056
www.daikincomfort.com
P/N: IOD-7031
Date: December 2013
Check the unit model number, specifications, and electrical char-
acteristics to determine if they are correct. In the event an incor-
rect unit is shipped, it must be returned to the supplier and must
NOT be installed. The manufacturer assumes no responsibility for
installation of incorrectly shipped units.
R
P
EPLACEMENT
ARTS
O
P
RDERING
ARTS
When reporting shortages or damages, or ordering repair parts,
give the complete unit model and serial numbers as stamped on
the product.
Replacement parts for this product are available through your con-
tractor or local distributor. For the location of your nearest dis-
tributor, consult the white business pages, the yellow page sec-
tion of the local telephone book or contact:
CONSUMER AFFAIRS
DAIKIN NORTH AMERICA LLC
7401 SECURITY WAY
HOUSTON, TEXAS 77040
855-770-5678
I
S
I
MPORTANT
AFETY
NSTRUCTIONS
R
S
S
ECOGNIZE
AFETY
YMBOLS
The following symbols and labels are used throughout this manual
to indicate immediate or potential hazards. It is the owner's re-
sponsibility to read and comply with all safety information and
instructions accompanying these symbols. Failure to heed safety
information increases the risk of property damage, product dam-
age, personal injury or death.
HIGH VOLTAGE!
D
ALL
ISCONNECT
POWER BEFORE SERVICING
M
ULTIPLE POWER SOURCES MAY BE PRESENT
TO DO SO MAY CAUSE PROPERTY DAMAGE
.
INJURY OR DEATH
, W
,
L
ORDS
AND
ABELS
WARNING
.
. F
AILURE
,
PERSONAL
Advertisement
Related Manuals for Daikin AHKD 20
Summary of Contents for Daikin AHKD 20
- Page 1 The AHKD series of electric heat kits is an accessory designed for NOT be installed. The manufacturer assumes no responsibility for installation with the Daikin DAR0904 or DAR1204 Airhandler ONLY. installation of incorrectly shipped units. INSTALLATIONS WITH OTHER AIRHANDLERS IS NOT PERMITTED.
- Page 2 ODEL DENTIFICATION WARNING Refer to this manual in combination with the instructions provided ONLY “E INDIVIDUALS MEETING THE REQUIREMENTS OF AN NTRY EVEL with the air handler for the correct installation procedure. ”, ECHNICIAN AT A MINIMUM AS SPECIFIED BY THE The electrical characteristics of the air handler, the electric heat (AHRI) ONDITIONING...
- Page 3 DAR0904 Temperature Rise Table (Degrees F) WARNING Heat Kit Supply Voltage Airhandler O AVOID PROPERTY DAMAGE PERSONAL INJURY OR DEATH DUE TO MUST ELECTRICAL SHOCK THIS UNIT HAVE AN UNINTERRUPTED 2800 UNBROKEN ELECTRICAL GROUND HE ELECTRICAL GROUND CIRCUIT 2900 MAY CONSIST OF AN APPROPRIATELY SIZED ELECTRICAL WIRE 3000 CONNECTING THE GROUND LUG IN THE UNIT CONTROL BOX TO THE 3100...
- Page 4 (MOP) Determine Wire Size The selection of the appropriate supply AXIMUM VERCORRECT ROTECTION wire size is important to the operation of the equipment. Every installation must include an NEC (USA) or CEC (Canada) ap- When selecting the wire size, the following are important proved overcorrect protection device.
-
Page 5: High Voltage
2. The heat kit attaches directly to the top panel (when viewed in the upflow position) of the air handler. Do not screw the heat kit into the duct flanges. Position the heat kit onto the air handler at the air discharge end with the control box orientated toward the airhandler front. - Page 6 Figure 5. Single Stage Heat - Single Stage Cooling where Figure 6. Two-Stage Heat - Single Stage Cooling where White White Green Brown Blue Green Blue Note: Brown wire is not used and is to be taped.
-
Page 7: Wiring Diagram
WIRING DIAGRAM WARNING Legend FR – Fan Relay FU – Fuse TB – Terminal Block HC – Heater Contactor HTR – Heater Element PLS – Primary Limit Switch SLS – Secondary Limit Switch Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring. - Page 8 WIRING DIAGRAM WARNING Legend FR – Fan Relay FU – Fuse TB – Terminal Block HC – Heater Contactor HTR – Heater Element PLS – Primary Limit Switch SLS – Secondary Limit Switch Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.