Download Print this page
Herman Miller Vista Installation And Disassembly For Recycling Instructions

Herman Miller Vista Installation And Disassembly For Recycling Instructions

Rectangular table with t-foot leg kit

Advertisement

Quick Links

HermanMiller
Vista™ Rectangular Table with T-Foot
Leg Kit Installation and Disassembly for
Recycling Instructions
How to assemble Rectangular Table
with T-Foot Leg Kit
Tools Required
Power Driver
Phillips Bit
Torque Wrench
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed,
including the following:
Read all instructions before using this furnishing.
DANGER
- To reduce the risk of electric shock always unplug this furnishing from
the electrical outlet before cleaning.
WARNING
- To reduce the risk of burns, fire, electric shock, or injury to persons:
Close supervision is necessary when this furnishing is used by, or near children,
invalids, or disabled persons.
Sitting or standing on product may cause risk of personal injury (use for chairs,
tables consider obvious misuse of product).
Use this furnishing only for its intended use as described in these instructions.
Do not use attachments not recommended by the manufacturer.
Never operate this furnishing if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return the
furnishing to a service center for examination and repair.
Failure to fully tighten screws (bolts) may cause injury by causing Vista tables to
collapse. Tighten screws (bolts) until they stop plus a quarter turn.
Periodically check to make sure legs are properly aligned. Failure to do so may
cause risk of personal injury.
HermanMiller
Metric Hex bit
Square Drive Bit
Torx Drive Bit
Parts Included (DV7GT)
Worksurface
Top Mounting
(Purchased Separately)
Plate
Stiffener
Switch
Tapping Screw
Cable Holder
Power Cord
If using power drive set on low torque.
Keep the cord away from heated surfaces.
Never drop or insert any object into any opening.
Do not use outdoors.
Do not operate where aerosol (spray) products are being used or where
oxygen is being administered.
This furnishing is intended for commercial use
control box rating: 5.0A, 120V
Duty cycle: 2 min on, 18 min off
1
1BN5FF rev A
T-Foot
Leg
Rectangle
Control Box
M10 Screw
Socket Screw
Counter Weight
Pan Head
Rolling Screw (4)
Installation Instructions

Advertisement

loading
Need help?

Need help?

Do you have a question about the Vista and is the answer not in the manual?

Questions and answers

Summary of Contents for Herman Miller Vista

  • Page 1 Return the furnishing to a service center for examination and repair. Failure to fully tighten screws (bolts) may cause injury by causing Vista tables to collapse. Tighten screws (bolts) until they stop plus a quarter turn.
  • Page 2: Grounding Instructions

    WARNING Step 1 - Risk of Electric Shock – Connect this furnishing to a properly grounded outlet only. See Grounding Instructions. Top Mounting Plate Installation For loading always put heavier items in the center and distribute the load. 1.1 Pick the side on the leg where the power cable runs, face the cable Risk of Injury - Maximum Load 250 lbs (113 kg).
  • Page 3 4.3 Install Tapping Screws in every other hole. Alternate back and forth on each flange. Note: If worksurface other than Herman Miller’s is being installed. Center legs front to back. Distance between legs to be determined by length of stiffener.
  • Page 4 Step 8 Step 9 8.1 Plug the switch cable to Control Box. 9.1 Plug the Power Cord to Control Box. Step 11 Step 12 11.1 Fasten the Cable Holders to the work surface with the switch and 12.1 Turn Table upright and plug in power cord to receptacle. leg cables in the Cable Holders.
  • Page 5 See instructions for details. For more information about our products and services please visit us at hermanmiller.com or call (800) 851 1196. ©2018 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A. Part No. 1BN5FF – A HermanMiller 1BN5FF rev A...