Related Manuals for Euroflex SMOOTH B2S
Summary of Contents for Euroflex SMOOTH B2S
- Page 1 timo alleato del tuo ferro ACTIVE IRONING BOARD WITH INTEGRATED STEAM BOILER AND PROFESSIONAL IRON INSTRUCTION MANUAL Before using this appliance, please read this instruction manual and keep it for future reference.
-
Page 2: General Safety Warnings
I M P O R TA N T S A F Dear Customer, We are delighted that you have purchased the Euroflex Smooth Active Ironing Board (B2S). Through proper assembly, use and maintenance the board will provide excellent ironing results for a long time. -
Page 3: Important Notices
E T Y I N F O R M AT I O N • This appliance is not to be used if it has been dropped, if there are visible signs of damage or if it is leaking. • Keep the appliance and its cord out of reach of children when it is in operation or cooling down. - Page 4 I M P O R TA N T S A F • Do not expose the appliance to water, dampness or heat. Only use indoors, not intended for outdor use. • Use a dry or slightly damp cloth to clean this appliance. •...
-
Page 5: Advice On Disposal
E T Y I N F O R M AT I O N ADVICE ON DISPOSAL 1. When this crossed-out bin symbol appears on a product it means that the product is covered by European Directive 2002/96/EC Disposal of your old appliance 2. -
Page 6: Product Overview
MADE ITALY MADE ITALY DOWN DOWN PRODUCT OVERVIEW 1. Power ON-OFF button 12. Iron soleplate 2. Power Indicator Light 13. Board height adjustment lever 3. Low water warning light 14. Iron steam socket 4. Steam ready indicator light 15. Iron steam/power cord 5. -
Page 7: Before Use
BEFORE USE Before starting the appliance for the first time, always remember that an improper use, assembly or maintenance can be hazardous. Please, carefully read the instructions on page 2,3,4,5. PREPARE YOUR IRONING BOARD POSITIONING When setting up the ironing board please note the following: •... - Page 8 To assemble the iron rest pad proceed as follows: • Pull out the metal frame from the rear part of integrated steam generator. • Put the rest pad on the metal frame following the instruction on it’s reverse side. • Press the rest pad hard on the metal frame to ensure it is fixed properly. Insert the iron cord support in one of the small holes on each side of the ironing board and hang the iron steam cord.
- Page 9 PREPARE YOUR IRONING BOARD • Remove the iron from the iron protection cover. • Plug the iron cable into the board steam socket. • Put the iron (soleplate down) on the rest pad. FILL THE TANK WITH WATER • Ensure that the electrical cable is disconnected from the power socket.
- Page 10 Information about the water This iron works with ordinary tap water. Decalcified water of any kind or water from tumble-dryers is not suitable, since it may be very corrosive. Never use water treated with filter cartridges, since the residues (e.g. particles of activated carbon) may block the mechanical parts of the appliance.
-
Page 11: Steam Ironing
As soon as the “steam ready” indicator light is on, the pressure is reached in the steam generator and the iron is ready for use.The heating time for the steam generator is about 10 minutes and can be reduced by using lukewarm tap water. No temperature regulation The iron has been designed to offer you the peace of mind of steam ironing any type of fabric. -
Page 12: Suction Function
DRY IRONING MADE • Put the iron on the iron-rest mat (20). ITALY • Turn the appliance on (power button 1). Simultaneously, the orange warming-up indicator light on the iron lights up (11). Later it switches off as soon as the soleplate reaches the required temperature.The iron reaches the required temperature after 3-5 minutes. -
Page 13: Synchro Mode
SYNCHRO MODE In synchro mode the suction/blowing function is activated when you press the steam button on the iron (10). • To activate the synchro mode set the selector switch on position “II” (7). DOWN CONTINUOUS MODE In continous mode the suction/blowing function MODE SWITCH is activated without interruption. -
Page 14: Maintenance
MAINTENANCE BOILER CLEANING (recommended every 6 months) • Always disconnect the power supply cord and ensure that the equipment is completely cool and the boiler contains no water. • Disconnect the iron from the steam supply. • Slowly unscrew the safety cap and remove it. •... -
Page 15: Changing The Cover
Euroflex ironing board covers. Metalised heat reflective covers and covers with thick lining are not suitable for this ironing system and may cause overheating of the suction motor. - Page 16 Distributed by: Echidna Sewing 56 Neumann Road CAPALABA QLD 4157 PH 07 33903600 Email: support@echidnasewing.com.au Imported by: Euroflex Australia Pty Ltd 79 Furniss Road DARCH WA 6065 AUSTRALIA TEL: 08 9302 2526 Email: admin@euroflex.com.au Website: www.euroflex.com.au Manufactured by: Plastecs SRL...
Need help?
Do you have a question about the SMOOTH B2S and is the answer not in the manual?
Questions and answers