Inepro PRO2 Series Short User Manual

Caution
• Turn off and if possible lock all sources supplying the
energy meter and the equipment that is connected to it
before working on it.
• Always use a properly rated voltage sensing device to
confirm that power is off.
• The connecting wire, connecting the device to the
outside circuit, should be sized in accordance with local
regulations for the maximum amount of the current
breaker or other overcurrent protection devices used in
the circuit.
• An external switch or a circuit-breaker should be
installed on the supply wires, which will be used to
disconnect the meter and the device supplying energy.
It is recommended that this switch or circuit-breaker is
placed near the meter because that is more convenient
for the operator. The switch or circuit-breaker should
comply with the specifications of the building's electrical
design and all local regulations.
• An external fuse or thermal cut-off used as an
overcurrent protection device for the meter must be
installed on the supply side wires. It's recommended
that this protection device is also placed near the meter
for the convenience of the operator. The overcurrent
protection device should comply with the specifications
of the building's electrical design and all local regula-
tions.
This short user manual does not contain every applicable safety regulation for using this meter. Also it might be required
because of company, local governement regulations or (inter)national laws to take additional measures. We have checked
the contents of this manual and every effort has been made to ensure that the descriptions are as accurate as possible.
However, deviations from the description cannot be completely ruled out, so that no liability can be accepted for any errors
or omissions in the information given. Versions might be different in default programming based on the customers order.
Certificates
This declaration of
Conformity is suitable
to the European
Standard EN 45014
General Criteria for
Supplier's Declaration
of Conformity. The
basis for the criteria
has been found in
international
documentation,
particularly in
ISO / IEC, Guide 22,
1982, Information on
manufacturer's
Declaration of
Conformity with
standards or other
technical
Specifications
Inepro Metering B.V. - Pondweg 7 - 2153 PK Nieuw Vennep - The Netherlands - T: +31(0)252 744044 -
Warning
• The installation should be performed by qualified
personnel familiar with applicable
regulations.
• Use insulated tools to install the device. A fuse, thermal
cut-off or single-pole circuit breaker should be fitted on
the supply line and not on the neutral line.
• This meter can be installed indoor, or outdoor
enclosed in a meter box which is sufficiently protected,
in accordance with local codes and regulations.
• To prevent tampering, an enclosure with a lock or a
similar device can be used.
• The meter has to be installed against a fire resistant
wall.
• The meter has to be installed in a well-ventilated and
dry place.
• The meter has to be installed in a protective box if the
meter is exposed to dust or other contaminants.
• The meter can be installed and used after being tested
and can be sealed afterwards.
• The device can be installed on a 35mm DIN rail.
• The meter should be installed on a location where the
meter can be read easily.
• In case the meter is installed in an area with frequent
surges for example due to thunderstorms, welding
machines, inverters etc., the meter is required to be
protected with a Surge Protection Device.
• The device should be sealed immediately after
installing it in order to prevent tampering.
• The device should be installed with a torque screw
driver.
We,
Declaration of Conformity
Inepro Metering BV
(supplier's name)
Pondweg 7
We
2153 PK Nieuw-Vennep
The Netherlands
Inepro Metering BV
(supplier's address)
Of
declare under our sole responsibility that the product:
Inepro Metering BV
PRO2-S
Pondweg 7
PRO2-2T
2153 PK Nieuw Vennep
PRO2-Mb
PRO2-Mod
The Netherlands
Single phase DIN rail Watt Hour meter
Ensure and declare that the apparatus:
(Name, type or model, batch or serial number, possibly source and number of items)
to which this declaration relates in conformity with the following European PRO2-S , PRO2-2T , PRO2-Mb and PRO2-Mod
harmonized and published standards at date of this declaration:
With the measurement range
EN 50470
(Title and or number and date of issue of the applied standard(s)) 230V, 5(100)A, 50Hz, 10.000imp/kWh
Following the provisions of the Directives (if applicable):
are in conformity with the type as described in the
N/A

EC-type examination certificate T11019
Nieuw-Vennep, 2017, May 5
and satisfy the appropriate requirements of the Directive 2014/32/EU
Place and date of issue
May 5, 2017
D. van der Vaart
Name of responsible for CE-marking
Daan van der Vaart
www.ineprometering.com
codes and
PRO2 series MID
Single phase energy meter
Short user manual
Version 2.18
Please note that this document is only a short user manual and does not handle every
function. The complete user manual is available at: www.ineprometering.com/download.
PRO2-S
PRO2-2T
PRO2-Mb
PRO2-Mod
Inepro Metering B.V. - PRO2 short user manual - Version 2.18 - 05.05.2017 - Subject to change without notice