Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Siebert XC610 Series
Summary of Contents for Siebert XC610 Series
- Page 1 Series XC610 Digital displays for work safety Operating instructions...
-
Page 2: Table Of Contents
Table of contents 1 Safety instructions Important information ............................3 Warning notice..............................3 Intended use ............................... 3 Special safety precautions for installation ......................3 Qualified staff..............................3 Protective low voltage ............................4 Mounting and installation ............................ 4 Transport ................................4 Disposal ................................ -
Page 3: Safety Instructions
Safety instructions Important information Read these operating instructions before starting the unit. They provide you with important information on the use, safety and maintenance of the units. This helps you to protect yourself and prevent damage to the unit. During the lifetime of the unit keep the operating instructions in an accessible place at all times. Hand over the operating instructions to any future owner of the unit. -
Page 4: Protective Low Voltage
For safety reasons and due to the required compliance with the documented unit properties the repair and replacement of components and modules may only be carried out by the manufacturer or an authorized specialized company. Protective low voltage The unit is powered by an included wall wart with 12 V. The unit has no power switch. -
Page 5: Important Information
Copyright This documentation is protected by copyright. All rights are reserved. No part of this documentation may be translated without written permission by Siebert Industrieelektronik GmbH. No part of this documentation may be reproduced in any form by print, photocopy or other methods, or processed by using electronic systems, duplicated or disseminated. -
Page 6: Important Start-Up Instructions
A cross-type cable for the RS232 interface between the PC and the display. If your PC does not have such an interface, you need an USB on RS232 converter. Siebert offers such a converter, together with the matching ready-made cable, as accessories. -
Page 7: Product Description
For each characteristic you can enter a fixed number. Alternatively, you can activated the automatic function to ensure that the field is counted by one further at midnight. The displays of the XC610 series are differed in the following interface versions: Order code... -
Page 8: Installation
Installation Requirements to the installation site The display is designed for wall mounting. The wall surface has to be plane and free of irregularities. The wall must have a sufficient capacity. CAUTION! If the wall surface is uneven the housing can be distored and damaged when mounting Installation material A parts kid with screws and dowels is included in delivery. -
Page 9: Power Supply Connection
Power supply connection After mounting the device on the wall you connect the line for the power supply. Therefore there is a jack on the printed circuit board. Once the power supply unit is plugged into the 230 V outlet, the display should light up. -
Page 10: Connecting The Configuration Interface
As connecting cable type J-Y(St)-Y, 2 x 0,6 mm² or similar is used. The maximum length is 10 meters. If your PC does not have a 9-pin sub-D connector, please use a matching USB adapter. You can get this as an accessory from Siebert. For normal operation of the display the serial connection is not needed. -
Page 11: Start-Up And Configuration
Start-up and configuration Configuration of the display For configuration of the display you need a PC. The necessary steps required for configuration are described in detail in the documentation of the program SafetyDisplayConfigurator. After you successfully completed the configuration the PC is no longer needed. Start-up and test Expediently perform a functional test before you close the device permanently. -
Page 12: Technical Data
Technicshe Technical data The following figures show the housing dimensions and the holes for wall mounting. holes for wall mounting 4,5 Series XC610 Dimensions (W x H x D) 420 x 297 x 26 mm LED display digit height 25 mm 100…240 V AC, 50/60 Hz Power supply Power consumption... -
Page 13: Service And Support
Service and Support If you have any questions or want to take advantages of our services, please contact one of the following addresses: Germany Siebert Industrieelektronik GmbH Siebertstrasse, D-66571 Eppelborn Phone +49 (0)6806 980-0 Fax +49 (0)6806 980-999 info.de@siebert-solar.com France Siebert France Sarl 4 rue de l’Abbé...
Need help?
Do you have a question about the XC610 Series and is the answer not in the manual?
Questions and answers