Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bego Otoflash
Summary of Contents for Bego Otoflash
- Page 1 OPERATING INSTRUCTIONS Otoflash English Otoflash...
-
Page 2: Table Of Contents
English ⋅ Otoflash This device documentation is part of the device and must be enclosed when selling or passing on the device. • The device has been designed solely for use in dental laboratories and comparable institutions for research, commercial and training purpos- es. -
Page 3: General Information
English ⋅ Otoflash General Information Importance of the operating Instructions These operating instructions cover all the infor- We welcome any suggestions or contributions; mation that is necessary according to the relevant please feel free to contact us. Your effort will help us... - Page 4 English ⋅ Otoflash Conventions These operating instructions contain references to DANGER residual hazards, important user tips and handling This reference identifies hazards that instructions that are identified with the following can cause serious bodily injury or symbols and words. death if the relevant hazard instruc- tions are not followed or not followed properly.
-
Page 5: Warranty And Liability
English ⋅ Otoflash Warranty and Liability Our "General terms and conditions of sale and • Failure to observe the notes contained in these delivery" apply. These are made available to the operating instructions regarding the transport, customer upon completion of the contract, at the storage, installation, commissioning, operation, latest. -
Page 6: Safety Instructions
English ⋅ Otoflash Safety instructions Special safety instructions regarding this device DANGER Danger due to electric shock Switch the device off and disconnect it from the power supply before carrying out any service or maintenance work! WARNING Risk of injury... -
Page 7: Device Description
English ⋅ Otoflash Device description Otoflash Otoflash is a flash-light polymerization device for the Compared to other light sources, this achieves a curing of light-curable resins. In the operating mode, better curing of the materials, resulting in very good two flash bulbs fitted at the bottom produce ten physical characteristics and reduced residual flashes per second. -
Page 8: Scope Of Delivery And Extras
Translation of the original operating instructions • Power cable (1x Europe, 1x USA/Japan) Accessories Cylinder pressure reducer for nitrogen....................20349 Wear Parts Flash module ............................20354 NOTE All wear parts listed here will not be replaced free of charge under the warranty or BEGO guarantee. -
Page 9: Technical Data
English ⋅ Otoflash Technical data Nominal voltage......................100,115, 230 Volt AC Nominal frequency ........................... 50/60 Hz Power consumption ........................ approx. 250 W Dissipated power ........................approx. 200 W Image frequency ......................10 flashes per second Lifetime of the flash tubes ................... average approx. 250 hours Digital timer .................... -
Page 10: Commissioning
English ⋅ Otoflash Commissioning Before commissioning, set the device to the correct input voltage using the selector switch (12) on the back of the device. When moving the device from colder to warmer ambient temperatures (e.g. transport in the winter), allow it to acclimatize for a minimum of 2 hours (to prevent the risk of flashovers inside the device). -
Page 11: Operation- Use With Timer
English ⋅ Otoflash Operation‒ Use with timer Setting the timer The device is switched on with the power switch (1), the green indicator labelled "Ready" (7) will light up and a 4-digit figure will appear on the display (4). This figure indicates the number of flashes. The... -
Page 12: Protective Gas Option
English ⋅ Otoflash Protective gas option In addition to the operating controls and installations Set the pressure regulating valve to 1.0 to 1.2 bar listed up to this point, the protection gas option also and connect the device to the nitrogen cylinder... -
Page 13: Service And Maintenance
Switch the device off disconnect it from the Service must only be carried out by the manufac- power supply. turer, BEGO or persons, who have been authorized Open the lid. by the manufacturer or BEGO. Remove the 4 screws inside of the device and pull the flash module (2) up and out. -
Page 14: Troubleshooting
English ⋅ Otoflash Troubleshooting Please contact the local retailer if the device is not Technical service hotline: +49 (421) 2028 - (270 … 274) working properly or if you have any other questions, Have servicing work carried out only by authorized...