Appleton N2LED Series Instruction Sheet

Emergency luminaire

Advertisement

Quick Links

Installation Instructions for N2LED Series Emergency Luminaire
Product Safety
FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS.
Signal Words Defined
DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous
situation which, if not avoided, could result in death or serious injury. CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury. NOTICE is used to address practices not related to physical injury.
Safety Instructions
WARNING:
!
• Before installation, ensure that the unit complies with the hazardous area classification. Failure to do so may result in bodily injury
and/or property damage. Refer to the fixture nameplate for suitability in specific hazardous locations.
• To prevent ignition of hazardous atmospheres, the area must be free of hazardous vapors before opening the enclosure or servicing
the fixture. To reduce the possibility of static sparking, do not attach metallic parts to the outside of the unit (e.g. metallic screws,
tags, decals, etc).
• Do not mount the unit near gas or electric heaters.
• De-energize the unit before opening.
• To reduce the risk of electric shock, disconnect AC power before servicing. To prevent arcing, avoid shorting the battery terminals.
CAUTION:
!
• Servicing of this equipment should be performed by qualified service personnel.
• Do not attempt to service the battery. The unit uses a sealed, NiCD battery which requires no maintenance. For replacement,
contact the factory.
NOTICE:
!
• Do not use this equipment for anything other than its intended use.
• The use of accessory equipment is not recommended and may cause an unsafe condition.
• Wiring and installation should be performed in accordance with the National Electrical Code® (NEC®) and other applicable
local code requirements.
Agency Ratings
I
• Class
, Division 2, Groups A, B, C, D
I
• Class
, Zone 2, Group
• Type 4X
• IP66
• Marine Outside Type (Salt Water)
Appleton • 1.800.621.1506 • www.appletonelec.com
II
C
650483-000 INSTRUCTION SHEET
650483-000 Rev. B 07/15 • Page 1 of 10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the N2LED Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Appleton N2LED Series

  • Page 1 650483-000 INSTRUCTION SHEET Installation Instructions for N2LED Series Emergency Luminaire Product Safety FOR PROPER AND SAFE INSTALLATION OF THIS PRODUCT, PLEASE READ THE FOLLOWING INSTRUCTIONS. Signal Words Defined DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury. WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
  • Page 2: Product Description

    INSTALLER CONNECTS 8.46 in. [215 mm] FOUR (4) LIGHT HEADS BATTERY TO PCA CONNECTOR 9.00 in. [228.6 mm] Figure 1: Description & Dimensions for N2LED2T1 Master Unit Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 2 of 10...
  • Page 3 INSTALLER CONNECTS 8.46 in. [215 mm] FOUR (4) LIGHT HEADS BATTERY TO PCA CONNECTOR 9.00 in. [228.6 mm] Figure 2: Description & Dimensions for N2LED0T1 Master Unit Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 3 of 10...
  • Page 4 (FOUR [4] PLACES) (FOUR [4] PLACES) 6.02 in. [153 mm] 6.69 in. [170 mm] 7.59 in. [192.8 mm] Figure 3: Description & Dimensions for N2LEDR2R1 Remote Unit Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 4 of 10...
  • Page 5 UNIT MOUNTING HOLES 6.02 in. [153 mm] (FOUR [4] PLACES) 6.69 in. [170 mm] 7.59 in. [192.8 mm] Figure 4: Description & Dimensions for N2LEDR1R1 Remote Unit Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 5 of 10...
  • Page 6: Installation

    Fasteners are not supplied. 4. Feed the AC power conductors through the conduit hub on top of the master unit. An Appleton nickel-plated enclosed hub with ground lug is provided for entrance to the AC power supply. AC input should be routed directly to the “AC IN” wiring terminal.
  • Page 7 315 ft. 12 AWG 500 ft. 10 AWG *Use copper wire between the power supply and the remote lighting system to limit the voltage drop to 5% Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 7 of 10...
  • Page 8 CONDUIT ENTRY CONDUIT GROUND PLATE WIRE CONNECTION USING WIRE NUT (TWO [2] PLACES) BONDING WIRE BLACK LIGHT HEAD 1 Figure 8: Wiring Diagram for N2LEDR1R1 Remote Unit Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 8 of 10...
  • Page 9: Self-Diagnostic Testing

    • Lamp head current. NOTE: The installed light heads will be tested if a “Learn Mode” has occurred; otherwise, a minimum of one (1) working light head is checked. Appleton • 1.800.621.1506 • www.appletonelec.com 650483-000 Rev. B 07/15 • Page 9 of 10...
  • Page 10: Maintenance

    Appleton warranties DO NOT extend to, and no reseller is authorized to extend Appleton’s warranties to any consumer. While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp, LLC. assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

This manual is also suitable for:

N2led0t1N2led2t1N2ledr2r1N2ledr1r1

Table of Contents