Elkay LZ Series Installation & Use Manual
Bottle filling stations & coolers
Hide thumbs
Also See for LZ Series:
- Installation, care & use manual (30 pages) ,
- Installation & use manual (21 pages) ,
- Quick start manual (2 pages)
Related Manuals for Elkay LZ Series
Summary of Contents for Elkay LZ Series
- Page 1 ENLZS8WS_1G Enhanced INSTALLATION & USE MANUAL Series Bottle Filling Stations & Coolers ™ Page 1 1000004538 (Rev. C - 07/19)
- Page 2 ENLZS8WS_1G Fig. 1 1000004538 (Rev. C - 07/19) Page 2...
- Page 3 ENLZS8WS_1G HANGER BRACKET INSTALLATION 1) Remove hanger bracket fastened to back of cooler by removing one (1) screw 2) Mount the hanger bracket as shown in Figure 1 (Pg. 2) NOTE: Hanger Bracket MUST be supported securely. Add fixture support carrier if wall will not provide adequate support. Anchor hanger securely to wall using all six (6) 1/4 in.
- Page 4 ENLZS8WS_1G Secure cooler frame to wall by installing (2) screws and washers (not supplied). FIG. 2 FIG. 3 Lay gasket along back of bottle filler mounting plate. Align BF and lay on cooler basin. Fig. 4 Attach the 3/8 water line into the bulkhead fitting. (Gasket removed from bottle filler for clarity) Fig.
-
Page 5: Wall Mounting Plate
ENLZS8WS_1G Fig. 7 Connect the bottle filler electrical harness. (Gasket removed from bottle filler for clarity) Fig. 6 MOUNTING BOLT HOLES (6) WALL MOUNTING PLATE BOTTLE FILLING UNIT Fig. 8 Page 5 1000004538 (Rev. C - 07/19) - Page 6 ENLZS8WS_1G 115V Refrigerated Wiring Diagram with Alpha/Numeric Display Fig. 9 Superseal Fitting Assembly OPERATION OF QUICK CONNECT FITTINGS OPERATION OF QUICK CONNECT FITTINGS SIMPLY PUSH IN SIMPLY PUSH IN TUBE IS SECURED PUSH IN COLLET TUBE IS SECURED PUSH IN COLLET TUBE TO ATTACH IN POSITION TUBE TO ATTACH...
- Page 7 ENLZS8WS_1G Basin Locknut BUBBLER DETAIL Fig. 13 NOTE: Filter Label Back of Filter When installing replacement bubbler and pedestal, tighten nut only to hold parts snug in position. Do Not Overtighten. Location Fig. 12 Fig. 14 WATERSENTRY Filter Detail ® WATERSENTRY FILTER PARTS LIST ®...
-
Page 8: Temperature Control
ENLZS8WS_1G Service Instructions Lower and Upper Shroud To access the refrigeration system and plumbing connections, remove four screws from bottom of cooler to remove the lower shroud. To remove the upper shroud for access to the pushbars, Fig. 15 regulator, solenoid valve or other components located in the top of the unit, remove lower shroud, disconnect drain, remove four screws from tabs along lower edge of upper shroud, unplug two wires and water tube. - Page 9 ENLZS8WS_1G Page 9 1000004538 (Rev. C - 07/19)
-
Page 10: Error Description
ENLZS8WS_1G Enhanced EZH2O Error Codes Error Error Description Corrective Action Code Bottle filler area obstructed • Remove obstruction. • Clean lens on IR sensor • Unplug unit for at least 30 seconds and restart • If error repeats, replace IR sensor E013 Missing or Incomplatible Filter •... -
Page 11: Filter Location
ENLZS8WS_1G Pictured is unit only without bottle filler. Note: Danger! Electrical shock hazard. Disconnect power before serviceing unit. Uses HFC-134A refrigerant Filter Location See Fig. 15 12 or 13 See Fig. 15 21, 24 Fig. 18 Page 11 1000004538 (Rev. C - 07/19) - Page 12 FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816 PRINTED IN U.S.A. REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640 ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com 1000004538 (Rev. C - 07/19) Page 12...