Advertisement
Preparation
Please check that all the parts are working correctly. Enter the factory preset code as on the code card (part
no.15), rotate the knob on the keypad one turn clockwise, re-enter the code and turn the knob anti-clockwise ensur-
ing that the follower on the back of the keypad rotates each time. The knob should return easily under its spring
pressure. If you intend to change the code please refer to 'how to change your code number' instructions
no.7)
prior to fitting.
Make sure that the Inside handle device (part no.2) rotates freely and returns under its spring pressure.
Check that the latch bolt on the tubular latch (part no. 4) moves freely by pressing the latchbolt at the end, and also
turning the spindle (part no. 10 or 11) in the hour glassed shaped follower on the tubular latch.
Determining the hand of the door
Many of the installation instructions refer to the handing
of the door. The hand of the door is determined with the
door in its closed position from the exterior or keypad
side of the door.
A) Right hand door – door opens inward (push), hinged
on the right side.
B) Left hand door – door opens inward (push), hinged
on the left side.
C) Right hand inward opening – door opens outward
(pull), hinged on the right side.
D) Left hand inward opening – door opens outward
(pull), hinged on the left side
If the unit is being fitted to a right hand hung door as per the 'determining
A
B
the hand of the door' nothing will need to be changed on the unit.
If the unit is being fitted to a left hand hung door the only part that will
need to be changed would be the blue handing screw on the back of the
inside handle from point A to point B as per the diagram.
Fitting the Latch Support Post
Fit the latch support post
(part no.8) in hole A for a right hand hung door or
B for a left hand hung door. Please refer to the 'determining the hand of the
door' if you are unsure what hand of door you have.
V3
Inside
A
C
Outside
Changing the Handing of the Unit
A
2
How To Change Your Code Number
1. Remove the lock from the door, which is done by removing the two screws at the very top and bottom of the
inside handle.
(page
2. With the keypad off the door turn the keypad over and on the reverse you will see two red screws and if from
an earlier model four red screws. Remove the two or four red screws which are securing a plate on with 14
small holes. Take care when removing the red screws as behind the plate are fourteen small springs.
3. With the plate removed you will now see that there are five red tipped (coded) tumblers, eight blue (non-
coded) tumblers and one uncoloured tumbler ('C' button).
4. To change the code, push and hold the 'C' button. Do not turn the keypad over as this will result in all
of the coloured tipped tumblers falling out. With the 'C' button held in the red tipped (coded) tumblers and
blue tipped (non-coded) tumblers can easily be lifted out using the tweezers supplied (part no. 5).
Please remember that the C tumbler should never be removed and should always be pressed in when
B
removing or replacing the coded or non-coded tumblers. Failing to hold the 'C' button in when chang-
ing the code may result in a damaged lock.
5. Please note the different shapes of tumblers before reinserting them into the lock body. Firstly there is a
difference in shape between the red tipped (coded) and blue tipped (non-coded) tumblers, as illustrated below.
D
When inserting the tumblers into the lock body they must be fitted facing the correct way, again see the illustra-
tions below. All square cut-outs must face outwards, regardless of whether they are coded or non-coded.
If you are inserting a tumbler into the 6, 7, 8, 9, 0, or Z positions the square cut-out of the tumbler need
to be facing towards the left and the dimple on the tumbler facing downwards. If you are inserting a
tumbler into the 1, 2, 3, 4, 5, X or Y positions the square cut-out of the tumbler need to be facing to-
wards the right and the dimple facing upwards.
6. If for instance the keypad needed to be coded to 1, 2, 3, 4, 5 you would hold the 'C' button down and using
the tweezers supplied (part no. 5) arrange the red tumblers so that they are in the 1, 2, 3, 4 and 5 positions
and in the remaining 8 positions blue tumblers will need to be inserted.
Please note that the code is not sequential and if for instance the unit was coded to 1, 2, 3, 4, 5 the
code can be entered 5, 4, 3, 2, 1 or any sequence as long as all of the digits in the code have been
pressed.
7. After you have refitted the tumblers and made a note of the new code, replace the plate with the 14 small
springs on and secure in place with the two or four red screws.
8. With the lock coded and the plate on the back refitted, ensure that the new code works 3 - 4 times before
refitting it to the door. Once fitted to the door check the code once more before closing.
Square
cut-out
B
Blue Non-Coded
Square
cut-out
Square
cut-out
Red Coded
Tumbler
Outwards
Tumbler
7
Square
cut-out
Outwards
Buttons
V3
Advertisement
