Operating and installation instructions ProLine gas wok burner To prevent the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en-AU, NZ M.-Nr. 09 317 370...
For trouble-free operation of the appliance, it is best to use it in the countries specified for use. For use in other countries, please contact Miele in your country.
Contents Warning and Safety instructions................ 5 Caring for the environment ................ 16 Overview....................... 17 Wok burner ......................17 Operating controls....................18 Burner........................19 Accessories supplied .................... 20 Before using for the first time ................ 21 Cleaning the ProLine element for the first time ............. 21 Switching on the ProLine element for the first time ..........
Contents Installing several ProLine elements.............. 43 Installation...................... 45 Electrical connection .................. 49 Gas connection.................... 51 Burner ratings ...................... 54 Conversion to another type of gas .............. 55 Jet table......................... 55 Changing the jets ....................55 Checking the first intake of air................ 58 Changing the small jets ..................
They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions. Keep these instructions in a safe place and ensure that new users...
The wok burner is not suitable for outdoor use. It is intended only to cook food and keep it warm. Any other use is not supported by Miele and could be dangerous. This appliance is not intended for use by persons (including...
Warning and Safety instructions Safety with children Young children must not be allowed to use this appliance. Older children may only use the gas wok burner if its operation has been clearly explained to them and they are able to use it safely. They must be aware of the potential dangers caused by incorrect operation.
Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician. Damage to the wok burner can compromise your safety. Check the appliance for visible signs of damage. Never use a damaged wok burner.
– the gas inlet valve is closed. Danger of electric shock! Do not use the wok burner if it is faulty. Switch it off immediately. Disconnect it from the mains electricity and gas supply. Call Miele.
Warning and Safety instructions If the wok burner is installed behind a furniture door, do not close the door while the appliance is in operation. Heat and moisture would build up behind a closed furniture door, potentially causing damage to the appliance, the furniture unit and the flooring. Do not close the door until the appliance has cooled down and the residual heat indicators have gone out.
Warning and Safety instructions Correct use The appliance gets hot when in use and remains hot for some time after being switched off. Do not touch the appliance if there is a possibility that it could still be hot. ...
Warning and Safety instructions When the wok burner is switched on, either deliberately or by mistake, or when there is residual heat present, there is the risk of any metal items left on the wok heating up, with the danger of burning.
If the pan diameter is too large, flames can spread out to the sides and damage or burn the worktop, wall claddings or surrounding units and also parts of the cooktop. Miele cannot be held liable for this type of damage.
Warning and Safety instructions If the appliance has not been used for a long period of time it should be thoroughly cleaned before it is used again. It is also advisable to have the appliance tested by a qualified person for safety.
Warning and Safety instructions Cleaning and care Do not use a steam cleaning appliance to clean this wok burner. Pressurised steam could reach the electrical components and cause a short circuit.
Caring for the environment Disposal of the packing Disposing of your old material appliance The transport and protective packaging Electrical and electronic appliances has been selected from materials which often contain valuable materials. They are environmentally friendly for also contain specific materials, disposal, and can normally be recycled.
Overview Operating controls Symbol Description Burner off, the gas supply is turned off Ignition position Largest flame: Inner and outer burner at highest setting. (2x) Large flame: Outer burner at lowest setting, inner burner at highest setting. ...
Overview Accessories supplied The accessories supplied with your appliance, as well as a range of optional ones, are available to order from Miele (see “Optional accessories”). Wok ring The wok ring supplied gives additional stability to the wok, especially to woks with a rounded base.
Before using for the first time Please stick the extra data plate for Switching on the ProLine the appliance supplied with this element for the first time documentation in the space provided The metal components have a in the “Service” section of this protective coating which when heated booklet.
Suitable cookware Wok ring Use the wok ring supplied to give additional stability to the wok, especially to woks with a rounded base. Make sure that the wok ring is located securely in its correct position. See illustration. The wok is unique among cookware in that it has a small base diameter and a large rim diameter (usually 35-40 cm).
Tips on saving energy – Use a pan lid whenever possible to minimise heat loss. – Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster. – Cook with as little water as possible. – Reduce the power setting once the water has come to the boil or the oil is hot enough to fry in.
Operation Switching on during a power outage Risk of fire with overheated food. If there is an interruption to the Unattended food can overheat and electricity supply, the gas can be ignite. ignited manually, e.g. with a match. Do not leave the cooktop unattended whilst it is being used.
Operation Adjusting the flame Switching off Turn the control knob clockwise to As the outer part of the flame is much the position. hotter than the centre, the tips of the flames should stay beneath the pan This stops the flow of gas and base.
Safety features Thermo-electric flame failure monitor Your wok burner is equipped with a thermo-electric flame failure monitor. If the gas flame is extinguished, e.g. by food boiling over or by a draught, the gas supply is switched off. This prevents the release of gas. If you turn the control knob to the position, the burner is ready for use again.
Cleaning and care Unsuitable cleaning agents Risk of burning due to hot surfaces! To avoid damaging the surfaces of the The surfaces will be hot after use. appliance, do not use: Switch the wok burner off. – cleaning agents containing soda, Allow the surfaces to cool down alkalines, ammonia, acids or before cleaning the wok burner.
Finally, dry with a clean soft cloth. Useful tip: The Miele care product for stainless steel can be used after cleaning to help maintain your appliance in good condition (see “Optional accessories”).
Cleaning and care Pan supports Danger of explosion! Remove the pan supports. Blocked flame openings can cause a dangerous build-up of gas in the Clean the pan supports in the base of the cooktop which could dishwasher or with a solution of warm ignite and cause an explosion.
Cleaning and care Assembling the burner Burners cannot function Place the burner head onto the correctly if they are incorrectly burner base so that the flame assembled. This can lead to damage failure monitor and the ignitor to the appliance and injury. extend through their respective holes Ensure that all parts of the burner are in the burner head.
Miele. This will save you time and money because you will not need a service call. If, after reading this guide, you cannot remedy the problem yourself, please call Miele (see back cover for details).
The ignitor on the The mains circuit breaker has tripped. burner does not spark. If it has, contact a qualified electrician or Miele. There is food residue stuck between the ignitor and the burner cap. The flame failure monitor is dirty.
These products can be ordered from the Miele online shop. They can also be ordered directly from Removes heavy soiling, limescale Miele (see end of this booklet for deposits and aluminium residues. contact details). Original Miele all purpose microfibre cloth...
Safety instructions for installation Damage from falling objects. Take care not to damage the ProLine element when fitting wall units or a rangehood above it. Fit the wall units and the rangehood before the ProLine appliance. The veneer or laminate coatings of worktops (or adjacent kitchen units) must be treated with 100 °C heat-resistant adhesive which will not dissolve or distort.
Safety distances Safety distance above the ProLine appliance A minimum safety distance must be maintained between the ProLine appliance and the rangehood above it. See the rangehood manufacturer's operating and installation instructions for details. If the rangehood manufacturer's instructions are not available or if flammable objects are installed above the ProLine appliance (e.g.
Safety distances Clearance underneath the appliance A minimum safety clearance of 30 mm must be provided underneath the appliance. Please note that clearance must also be provided for the installation of the flexible gas connection hose and mains electrical cable if the appliance is to be installed above a closed surface (e.g.
Safety distances Safety distances to the sides and back of the appliance Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall on one side (right or left). On the other side, however, no tall unit or wall should stand higher than the appliance.
Safety distances A gas appliance shall be installed such that the surface temperature of any nearby combustible surface* will not exceed 65 °C above ambient. The minimum clearance from a combustible surface shall be a 200 mm horizontal distance from the periphery of any gas burner (AS/NZS 5601.1).
Installation notes Sealing between the ProLine Tiled worktop element and the worktop Grout lines and the hatched area underneath the ProLine element frame must be smooth and even. If they are The ProLine element and the not, the ProLine element will not sit worktop may be damaged if the flush with the worktop and the sealing appliance needs to be removed after...
Building-in dimensions a Spring clamps b Front c Building-in depth d Building-in depth for the mains connection box with mains connection cable, L = 2000 mm e Building-in depth for the gas connection R 1/2 - ISO 7-1...
Building-in dimensions Distances from burner to the edge of the appliance...
Installing several ProLine elements Example: 3 ProLine elements a Spring clamps b Spacer bars c Gap between spacer bar and worktop d Cover strips e ProLine element width less 8 mm f ProLine element width g ProLine element width less 8 mm h Worktop cut-out...
Installing several ProLine elements Calculating the worktop cut-out The frames of the ProLine elements overlap the worktop at the outside right and left by 8 mm on each side. Add up the widths of the ProLine elements and subtract 16 mm from this sum. Example: 288 mm + 288 mm + 380 mm = 956 mm - 16 mm = 940 mm The ProLine elements are 288 mm, 380 mm or 576 mm wide depending on...
Installation Preparing the worktop Make the worktop cut-out as shown in “Building-in dimensions” or as calculated (see “Installing several ProLine elements”). Remember to maintain the minimum safety distances (see “Safety distances”). Wooden worktops Seal the cut surfaces of wooden worktops with a suitable heat- resistant sealant to avoid swelling caused by moisture.
Installation Granite and marble worktops You will need heavy-duty double- sided tape (not supplied) to secure the spring clamps and spacer bars. Apply silicone adhesive to the side edges and bottom edge of the spring clamps and spacer bars . ...
Installation Fitting several ProLine elements Fitting the ProLine appliance Push the built-in ProLine element to Feed the mains connection cable the side until the holes in the spacer down through the worktop cut-out. bar can be seen. Starting at the front, position the ProLine appliance in the worktop cut- out.
Installation Connecting the ProLine Removing a ProLine appliance appliance If the ProLine element is accessible from below, push it upwards to Connect the ProLine element/ remove it. Push the back of the elements to the electricity supply and appliance out first.
Risk of damage from incorrect by a suitably qualified and competent connection. person in strict accordance with current Danger of injury! Miele cannot be local and national safety regulations. held liable for unauthorised Connection of the ProLine appliance to installation, maintenance and repair...
If the mains cable needs to be replaced, it must be replaced with a special connection cable, type H 05 VV-F (PVC insulated), available from Miele, by a Miele authorised service technician or suitably qualified and competent electrician in order to avoid a hazard.
Gas connection Check with your local gas supplier Risk of explosion due to an about the type of gas supplied and incorrect gas connection. compare this information with the If the gas connection is carried out type of gas quoted on the incorrectly, it may result in gas appliance's data plate.
Miele. Conversion to another type of gas is described in the section Connect the cooktop to the gas “Conversion to another type of gas”.
Gas connection For Natural gas models Setting the gas pressure The gas regulator is only included with The gas pressure must be set by the appliances which are set up for authorised gas fitter as shown on the connection to natural gas. The data plate: regulator must be connected directly Natural gas 1.0 kPa...
Conversion to another type of gas Changing the jets Risk of explosion due to an incorrect conversion. Disconnect the cooktop from the If the conversion to another type of electricity supply and turn off the gas gas is carried out incorrectly, it may supply.
Conversion to another type of gas Changing the main jet Lift the top of the appliance off. Remove the burner caps , burner ring and burner head . Undo the screws . Unscrew the main jet anti-clockwise Pull the control knob off. from its housing with an SW 10 spanner while counterholding it with an SW 13 spanner (see picture).
Conversion to another type of gas To change the jet for the inner burner d Jet (main jet for the inner burner) e Air intake sleeve f Vent Remove the screw from the fitting with an SW 8 spanner while counterholding it with an SW 12 spanner.
Conversion to another type of gas Checking the first intake of air Changing the small jets a Retaining screw b Air intake sleeve a Small diameter jet (e.g. for ULPG gas: 0.23) Gap X must measure: b Large diameter jet For natural gas: 13 mm (e.g.
Conversion to another type of gas Checking operation Check all gas fittings for leaks. Reassemble the cooktop. Ignite all burners to check that they are operating correctly. – The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.
Service Contact in case of fault In the event of any faults which you cannot remedy yourself, please contact Miele. Contact information for Miele can be found at the end of this booklet. Please quote the model and serial number of your appliance when contacting Miele.
Miele Experience Centre South Melbourne: Freemans Bay, Auckland 1011 206-210 Coventry Street South Melbourne, VIC 3205 Miele Experience Centre Auckland: Miele Experience Centre and Office Sydney: 8 College Hill 3 Skyline Place Freemans Bay, Auckland 1011 Frenchs Forest, NSW 2086 Telephone:...