Download
Share
Print this page
  1. Manuals
  2. Brands
  3. stellar labs Manuals
  4. Indoor Fireplace
  5. CTL-58 Series
  6. Installation and operating instructions manual

stellar labs CTL-58 Series Installation And Operating Instructions Manual

Linear direct vent gas fireplaces
Hide thumbs Also See for CTL-58 Series:

Advertisement

Quick Links

Download this manual
D O N O T D I S C A R D
D O N O T D I S C A R D

Advertisement

loading
Need help?

Need help?

Do you have a question about the CTL-58 Series and is the answer not in the manual?

Questions and answers

Related Manuals for stellar labs CTL-58 Series

Summary of Contents for stellar labs CTL-58 Series

  • Page 1 D O N O T D I S C A R D D O N O T D I S C A R D...
  • Page 7 ◄ ► ▲ ▼ ▲ ▲ ▼ ▲ ◄ ► 2-1/8 (203 mm) (54 mm) ▼ ◄ ► ▲ ▲ ◄ ► ◄ ► 28-1/8 (714 mm) ▲ ▼ ▼ ▼ ◄ ► 7-7/8 (200 mm)
  • Page 8 ▼ ▲ 1-3/4” ► ◄ 1-3/8” (45mm) (35mm) 1/8” ►◄ (3mm) ◄ ► 12” (305mm)
  • Page 10 53-1/2” ◄ ► (1,359mm) 25-1/2” (648mm) ▼ ▲ 3/4” (19mm) (Hearth) Bottom of fireplace.
  • Page 11 Stand-Off Bracket Stand-off Heat Shields Stand-Off Bracket IMPORTANT: The top stand-off brackets (2) are attached to the fireplace top in a flat state for shipping and will need to be bent up into shape by bending at the perforations on each end and in the middle.
  • Page 12 NOTE: Interior framing shown. Add sheetrock thickness to framing depth for exterior walls. 10”H x 10”W (254mm x 254mm) Opening required for horizontal terminations ▲ ▼ ▼ ▲ For clearance of front to floor or hearth extension: Eminence and Inspiration = 2-1/4” (57mm) Accent = 3/4”...
  • Page 14 ▲ ◄ ► ▼ ◄ ►...
  • Page 16 Non-Combustible Zone: No materials allowed on top of the fireplace within shaded area for entire width and depth of fireplace. This air space MUST remain open. Mantel 28-1/8” (715 mm) 12” (304.8 mm) 62-1/4” x 13-1/2” 16” (1,581mm x 343mm) (406.4 mm) Non-combustible board 55-3/4”...
  • Page 17 ▼ ▼ ▼ ▼ ▼ ▼ ▼ ▼ (4) Top latches for glass frame assembly (4) Bottom latches for glass frame assembly ▼ ▼ Pull latches ‘OUT’ and ‘UP’ to release Pull latches ‘OUT’ and ‘DOWN’ to release Pull latches ‘OUT’ and ‘DOWN’ to attach Pull latches ‘OUT’...
  • Page 21 Vertical ◄ Termination Cap ▲ Minimum: 10 ft. (3.05m) Maximum: 40 ft. (9.14m)

  • Page 22: Wall Thimble

    NAILS, 4 REQUIRED EXISTING CEILING JOISTS CEILING FIRESTOP NEW FRAMING CEILING BELOW NAILS, 4 REQUIRED WALL THIMBLE CEILING FIRESTOP...
  • Page 23 (6.1 m) 10 12 18 20 22 (12.9 m) (6.1 m) 28” (711 mm)
  • Page 24 AREA WHERE TERMINAL IS NOT PERMITTED VENT TERMINAL AIR SUPPLY INLET...
  • Page 25 Inside Corner Outside Corner Recessed Location A = Combustible 9” (229mm) F= Combustible 6” (152mm) = Non-combustible 2” (51mm) = Non-combustible 6” (152mm) Balcony Balcony with perpendicular side wall with no side wall C = Clearance from corner in recessed location = Combustible 9”...
  • Page 26 LOWEST VENT CAP DISCHARGE OPENING ▲ GAS VENT ▼ ROOF PITCH IS X/12 H (Min.) - Minimum height from roof to lowest discharge opening...
  • Page 27 Non-combustible board included, shipped on back of unit 62-1/4” x 13-1/2” (1,581mm x 343mm) Combustible wall covering OK up to within 1/8” (3mm) of the side of the unit. ◄ Do not overlap the black unit face. Stop the finishing material on the top of the hood rock stop.
  • Page 28 Stop finishing material at the top of the unit. ▼ ▲ Finishing materials up to 1” (25mm) 24-1/4” thick may come to the (616 mm) sides of the unit. Front will overlap the ▼ finishing materials. ◄ ► 51” (1,295 mm) Stop finishing material at the bottom of the unit.
  • Page 29 Center the unit in a 61-1/2” x 27-3/8” (1,562mm x 695mm) opening in the finishing material. 1-1/2” (33mm) ▼ ▼ ▲ ▲ 27-3/8” (695mm) ▼ ▼ ▲ ▲ 1-1/4” 61-1/2” (33mm) ◄ ► (1,562mm) Finishing material up to 2” (51mm) thick may come to these lines. Front will overlap the finishing materials by 1/2”...
  • Page 33 ▲ ▲ 6-3/4” (171 mm) 5” (127 mm) ▼ ▼ 12-1/8” ◄ ► 10 -11/16” ► ◄ (308 mm) (271 mm)
  • Page 34 ▲ ▲ 5-1/8” 4-1/2” (130 mm) (114 mm) ▼ ▼ 8-11/16” ◄ ► 11-7/16” (221 mm) ► ◄ (291 mm) ▲ ▲ 6-3/16” 4-3/8” (157 mm) (111 mm) ▼ 11-5/8” 10-11/16” ◄ ► ◄ ► (271 mm) (295 mm)
  • Page 35 ▲ 6-3/16” (157 mm) ▼ 11-5/8” ► ◄ (295 mm) ▲ ▲ 4-15/16” 4-5/16” (125 mm) (110 mm) ▼ ▼ 8-7/8” 11-13/16” ◄ ► ◄ ► (225 mm) (300 mm)
  • Page 36 ▲ ▲ 6” 4-3/8” (152 mm) (111 mm) ▼ ▼ 12” 10-3/16” ◄ ► (305mm) ◄ ► (259 mm) Step 8: Burning Embers, part # STL-REMB...
  • Page 39 FLAME SENSOR IGNITOR PILOT NUT OUTLET PRESSURE TAP (MANIFOLD PRESSURE) “PILOT WIRE CONNECTION” LOW LIMIT SCREW (LLS) ALUMINUM CAP INLET PRESSURE TAP NG/LP PLUNGER UNDERNEATH PILOT ADJUSTMENT SCREW “MAIN” WIRE CONNECTION...

  • Page 40: Battery Pack

    WIRE HARNESS CONNECTION TO VALVE STEPPER MOTOR WIRE HARNESS CONNECTION LEARN BUTTON TO EXTENSION MODULE 120 VAC ADAPTER CONNECTION ▲ ▲ ▲ ▲ PILOT SENSOR PILOT IGNITOR CONTINUOUS REMOTE CONNECTION CONNECTION PILOT SWITCH ON/OFF SWITCH BATTERY PACK 120 VAC ADAPTER FAN PLUG-IN RECEPTACLE ▲...
  • Page 42 NOTE: When in Battery Mode, the only functions available are turning the replace on or o . No ame adjustments are available nor will the remote control be available for the fan, ember lights, thermostat, etc. WIRE HARNESS CONNECTION TO VALVE STEPPER MOTOR WIRE HARNESS CONNECTION LEARN BUTTON TO EXTENSION MODULE...
  • Page 46 WIRE HARNESS CONNECTION TO VALVE STEPPER MOTOR WIRE HARNESS CONNECTION LEARN BUTTON TO EXTENSION MODULE 120 VAC ADAPTER CONNECTION ▲ ▲ ▲ ▲ PILOT SENSOR PILOT IGNITOR CONTINUOUS REMOTE CONNECTION CONNECTION PILOT SWITCH ON/OFF SWITCH...
  • Page 57 PRESSURE REGULATOR CAP FLAME SENSOR IGNITOR PILOT NUT...
  • Page 58 OUTLET (MANIFOLD) PRESSURE SCREW INLET PRESSURE SCREW...
  • Page 59 Consult your dealer information on optional accesoories available for this fi replace. This appliance tested & certifi ed by: Underwriters Laboratories, Northbrook, IL ellar Hearth Products 14351 Ewing Avenue S Burnsville, MN 55306 (P) 952.224.4072 (E) info@stellarhearth.com...
  • Page 60 Limited Lifetime Warranty Stellar Hearth Products, a brand of Big Woods Hearth Products Inc, warrants the following components for life to the original owner, subject to proof of purchase: Firebox, Heat Exchanger, Combustion Chamber, Grate and Stainless Steel Burners. Electrical components and wearable parts (gas valve, blowers, wiring, switches, remote controls, gasketing, and pilot assembly) are covered and will be provided free of charge for a period of one year from date of purchase.

This manual is also suitable for:

Cml-58-afCtl-58-afCml-58 series