Inverto IDLV-3440DM User Manual

Professional 4-channel dvb receiver and transmodulator

Advertisement

Quick Links

IDLV-3440DM
Professional 4-Channel DVB Receiver and
Transmodulator

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IDLV-3440DM and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Inverto IDLV-3440DM

  • Page 1 IDLV-3440DM Professional 4-Channel DVB Receiver and Transmodulator...
  • Page 3 IDLV-3440DM Professional 4-Channel DVB Receiver and Transmodulator User Manual...
  • Page 5: Table Of Contents

    Table of Contents Notices Before using the device Overview Front panel and Rear panel instructions Operation instructions via Front Panel Web Control Installation Accessories Technical Specifications Safety Warrenty, service and support...
  • Page 6: Notices

    Notices COPYRIGHT (Copyright © 2015 Inverto Digital Labs ) Not to be copied, used or translated in part or whole without Inverto prior consent in writing except approval of ownership of copyright and copyright law. WARRANTY This warranty does not cover parts which may become defective due to misuse of the information contained in this manual.
  • Page 7: Before Using The Device

    The supplied AC power cable must be used to power the device. If the power cord becomes damaged it must be replaced. No operator serviceable parts inside. Refer servicing to Inverto trained and approved service engineers. For the correct and safe use of the device, it is essential that both operating and servicing personnel follow generally accepted safety procedures in addition to the safety precautions specified in this manual.
  • Page 8: Overview

    Overview IDLV-3440DM integrates 4 DVB Receiver and Transmodulator in one 1U 19” chassis. It provides operators an ideal DTV headend setup solution by combining multi-channel receiving, descrambling, remultiplexing and DVB QAM/ COFDM modulation and TS over IP operations together in one single unit. Equipped with 4 independent tuner front ends with various factory options for DVB-T/T2, DVB-S2/S, DVB-C, DTMB, ISDB-T and ATSC types, standard ASI and TS/IP I/O interfaces, IDLV-3440DM ensures compatibility with all types of transmission media.
  • Page 9: Front Panel And Rear Panel Instructions

    Front panel and Rear panel Instructions FRONT PANEL LED POWER LED WARNING LED ALARM VFD DISPLAY CONTROL LED TUNER LOCK TS/IP RF MONITOR OPERATION BUTTONS MODULATOR STATUS -20dB LED POWER When turned on, the Green LED indicates that power is available. When turned off, the power is not available or failed LED WARNING Led On...
  • Page 10: Operation Instructions Via Front Panel

    REAR PANEL RS-232 Reserved for factory use Alarm Alarm relay interface Tuner In-1/4 4 Tuner Inputs Common Interface 4 Common Interfaces ASI Out-1/4 4 pass through ASI output ASI In ASI input ASI Out-5 Main ASI output ASI Out-6 Backup ASI output port RF Out Main RF output port RF In backup...
  • Page 11 DESCRIPTION OF MENU The main menu items can be selected with the keypad. By pressing the [Enter], the user navigates to the submenus, which are selected in the same manner. Status: Submenu Submenu Parameters Description Layer 1 Layer 2 Tuner Status Tuner 1/2/3/4 Lock/Unlock Tuner 1/2/3/4...
  • Page 12 Slave Board Setup – Tuner 1/2/3/4: Submenu Parameters & Description Default Value To configure the local oscillator frequency according to the right satellite, its LNB LO Frequency range is from 1000 to 26,500MHz. To configure the satellite down link frequency according to the Satellite Frequency right satellite, its range is from 1000 to 26,500MHz.
  • Page 13 ON: Remove the CA descriptors that are carried within the input- Remove CA ted TS over ASI or IP OFF: Keep the CA descriptors. ON: Insert EIT into the output stream, EIT data may come from Insert EIT ASI or IP input port OFF: Do not insert EIT into the output stream.
  • Page 14 Config – TS/IP (Full Duplex Mode): Submenu Parameters & Description Default Value Gigabit Out Switch: Gigabit Out Switch: Enable/Disable Source: Set the source for the IP output Remux Protocol: UDP: Set UDP protocol to IP output Protocol: UDP RTP: Set RTP protocol to IP output TS Pkts Per UDP: Set the number of TS packets that can be TS Pkts Per carried by each UDP packet, valid range from 1~7...
  • Page 15 Config – Modulation (QAM): Submenu Parameters & Description Default Value Modulator Output ON/OFF: put OFF to switch off the QAM carrier Encoder1/Encoder2/Encoder3/Encoder4: The stream output from the corresponding encoder will be delivered to modulator directly. Remux: The stream from built-in remux will be delivered to Output Source REMUX modulator...
  • Page 16 Config – RF Setting: Submenu Parameters & Description Default Value RF Frequency valid range from 30,000~1,000,000KHz 474000 RF Level valid range from 90~120dBuV RF Level adjust (-1dBuV~4dBuV) 0 dBuV Auto: Automatically output the RF signal inputted via Backup RF input port when the built-in modulator is down Backup Switch Auto Main: Always output from the built-in modulator...
  • Page 17: Web Control

    To operate a IDLV-3440DM, first make sure the Ethernet control port is well connected in the network and could be pinged by the host PC, and then enter the IP address of the IDLV-3440DM into the browser, there will be a pop-up showed asking for login user and password.After login the device can be operated.
  • Page 18 Status of Output: Status of Tuner: Status of Modulator:...
  • Page 19 Status of TS/IP Linkage: Status of Power Supply: CONFIGURATION All parameters for Tuners, CI, BISS, QAM Output, RF Setting and ASI Output can be found under the page “Configuration”. Click the button “Apply” to submit your configuration or click the button “Cancel” to cancel and restore the previous settings.
  • Page 20 Tuner: There are 6 options to set DVB-S2 parameters. After signal locked, the TUNER LOCK indicator on front panel will turn green. LNB Frequency: Input LNB frequency Satellite Frequency: Input downstream frequency of satellite Symbol Rate: Input symbol rate of satellite LNB Voltage: Select the correct LNB voltage output of the F-connector: Off, 13 V, 18 V.
  • Page 21 Modulation: In the page user can enable or disable and setup the source for each of the 4 independent built-in modulators and setup the parameters except the frequency. RF Setting: Set up the RF parameters in the page “RF setting”. The output RF frequency ranges from 30,000 to 1,000,000 KHz, and output RF level ranges from 90~110dBuV.
  • Page 22 REMUX In the “Remux” page, select the program(s) that to be remultiplexed and configure the necessary parameters for the new generated transport stream. Packet Size: 188 Byte / 204 Byte Bit Rate (Kbps): Set the bitrate for the new generated MPTS, valid range from 100~216000 Kb/s. The bitrate should be at least bigger than the total bitrate of selected programs, otherwise, packets may dropout.
  • Page 23 TS/IP IDLV-3440DM support two TS/IP operation mode, which are respectively Multiple Output Mode and Full Duplex Mode. To switch between the two mode please refer to chapter 7.6. Multiple Output Mode: Gigabit Out: There are up to 4 streams encapsulated onto TS/IP output when TS/IP is configured as multiple output mode. In this mode, all 4 TS streams from internal remultiplexier could be sent through the TS/IP port while the 5th IP slot could be fed with ASI input.
  • Page 24 Time To Live: Set TTL to the output IP packets Type of Service: Select the service type for the outputted IP streaming. Full Duplex Mode: In this mode, the IDLV-3440DM supports single uni/multicast input and output in parallel. Set the IP I/O parameters in following pages. Gigabit Out:...
  • Page 25 Gigabit Input: Note the Column and Row FEC UDP ports have to be configured if Pro-MPEG protocol is used in the IP signal inputted. Uni/Multicast IP Address: Set the multicast address for the incoming IP streaming. To receive a unicast streaming, the submenu can be ignored.
  • Page 26 SYSTEM The system page shows all information of the device, including device name, serial number, software version, and so on. User can implement the local network settings, TS/IP operation mode, modulation mode, software upgrade, remote reboot and so on. Device: Device name: Check the name and the serial number of this device.
  • Page 27 Version: User can check versions of the device, as shown in the picture below. Web Login: Username: Set the username for webpage login Password: Set the password for webpage login Factory Default: Click the button “Default” to restore the factory default settings to the device. Note: The IP address of the device and the operation mode of the Gigabit board will not be restored.
  • Page 28 User can reboot this device by clicking the button “Reboot”. Upgrade: IDLV-3440DM support online firmware upgrade. To upgrade the device, load the upgrade file first by clicking on “Browse…”, in the opened window select the correct upgrade file, then click on “Upgrade”, wait the device...
  • Page 29: Installation

    The user can save 16 groups settings on the unit and recall one of them to use. User can download these settings to the PC and use for other units also. Installation It is highly recommended to fix the IDLV-3440DM be mounted in EIA standard 19” rack, any other mounting method may lead to damage to the device. •...
  • Page 30: Technical Specifications

    Technical Specifications DVB-S/S2 Tuner Input (ISI Factory Optional) Connector Type 4×F type female 75Ω for Input Input Frequency Range 950 ~ 2150MHz Input Level -25 ~ -65dBm Symbol Rate 2 -45MBaud’s Roll Off Factor DVB-S QPSK: 0.35 DVB-S2 8PSK: 0.35, 0.25, 0.2 FEC Code Rate DVB-S QPSK: 1/2, 2/3, 3/4, 5/6, 7/8 DVB-S2 QPSK: 1/2, 3/5, 2/3, 3/4, 4/5, 5/6, 8/9,9/10...
  • Page 31 Descrambling Descrambler DVB Common Scrambling Algorithm (CSA) Common Interface 4 x PCMCIA slots, compatible with major CA CAMs in the market BISS Mode BISS-1, BISS-Ez QAM Modulation Standard of System ETSI EN300 492, ITU J.83, Annex A/C: 16/32/64/128/256QAM Symbol Rate 2.5~6.99 Bauds Constellation 16QAM, 32QAM, 64QAM, 128QAM, 256QAM...
  • Page 32 Data Encapsulation UDP, RTP Other Protocols Multicast/Unicast, IGMPv3,ARP Alarm Connector Type 1×D-sub 9 male Switching Condition User Defined Control & Monitoring Connector Type 1×RJ-45, 10/100 Base-T, for equipment IP Control Remote Control SNMP, HTTP (Web Interface), Proprietary HDMS (Headend Device Management System) Local Control VFD display and 6-key keypad Serial Port...
  • Page 33: Safety

    Safety CAUTION Unauthorized maintenance or the use of non-approved replacements may affect the equipment specification and invalidate any warranties.The device should be kept away from electric, strong magnetic and hot areas (temperature < 40°C; humidity < 85%). Keep away from high electric and magnetic areas Don’t keep the device in the dusty, humid and high-temperature environment.
  • Page 34: Warrenty, Service And Support

    Warranty, service and support This Limited Warranty applies only to the Product sold by Inverto Digital Labs, 18 Duchscherstrooss, L-6868 Wecker, Luxembourg (hereby, the “Company”) the Customer purchase for his own use and not for resale. The term “Product” in this Limited Warranty does not include any software programs, whether pre-loaded with the Product, installed subsequently or otherwise.
  • Page 35 In the event that a warranty service is required, you should contact your specialist dealer or the point of sale. Warrantee claims cannot be made directly to the company - Inverto Digital Labs. You should therefore keep your sales receipt as proof of purchase. The Company recommends the Customer first utilize support material shipped with the product, product diagnostics, information contained on the Web, and online support on http://www.inverto.

Table of Contents