Download Print this page

Linear Tube Audio MZ2 Series User Manual

Advertisement

Quick Links

MZ2
USER GUIDE:
Linear Tube Audio
Takoma Park, MD, USA
301-448-1534
hifi@lineartubeaudio.com
Regarding older models: While this user guide should cover the basics for
any MicroZOTL2.0, MicroZOTL2.0 Deluxe, or MZ2-S, please contact us if your
unit is different from the one described here and we can give you more
specific information.
WARNING: For safety, the cover of this amplifier should be secured at all
times.
This amplifier contains extremely high voltages and the user should not
attempt to service the amplifier.
Furthermore, this amplifier generates
radio-frequency energy that can interfere with communications
equipment.
Introduction
The MZ2 is a Class A tube amplifier utilizing ZOTL (Zero-hysteresis Output
Transformer-Less) technology. The MZ2 is an evolution of the original
microZOTL designed by David Berning in 1999. It is equally exceptional as
a headphone amplifier, preamplifier, and low-wattage integrated
amplifier.

Advertisement

loading
Need help?

Need help?

Do you have a question about the MZ2 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Linear Tube Audio MZ2 Series

  • Page 1 USER GUIDE: Linear Tube Audio Takoma Park, MD, USA 301-448-1534 hifi@lineartubeaudio.com Regarding older models: While this user guide should cover the basics for any MicroZOTL2.0, MicroZOTL2.0 Deluxe, or MZ2-S, please contact us if your unit is different from the one described here and we can give you more specific information.
  • Page 2 This warranty is void if improper voltage is applied to any input or output. If Linear Tube Audio determines after receiving the unit that damage was misrepresented and has been caused by something not covered by the warranty, the customer must pay for any necessary repairs before the unit is returned to the customer.
  • Page 3 Specifications Circuit Type: Push-Pull Class A Power Output: 1W (4 Ohm), 0.5W (8 Ohm) Input Sensitivity: 0.6V RMS for full output Input Impedance: Output impedance: 2 Ohms (measured at 0.5A, 60 Hz) Preamp Output Impedance: 50 Ohms Gain: 10.3dB (4 Ohm load) 12.4dB (8 Ohm load)
...
  • Page 4 Quick Start Remove amplifier, power supply, and included cables from the box. Attach the DC umbilical to the power supply and amplifier. This has a locking 2.5mm x 2.5mm barrel connector on both sides. Plug in completely and tighten the locking nut. If you have an LPS+, check that the red voltage label reflects approximately your area’s voltage (115/220).
  • Page 6 Operation If you prefer, you can leave the power supply on indefinitely and only use the power button on the front panel. The front panel features a power button, input switch, volume knob, and headphone jack. There are 3 RCA pairs on the back for 3 inputs, selectable via toggle switch on the front panel.
  • Page 7 Tube Heater Voltage Jumper Settings The MZ2 can use 6SN7 or 12SN7 tubes as its output tube. When switching from one to the other, be sure to set the jumpers on the boards to the correct position. A 6-volt tube like the 6SN7 will burn out quickly if being given 12 volts.
  • Page 8 For more information and FAQs please visit www.lineartubeaudio.com or contact us at hifi@lineartubeaudio.com NOTES...

This manual is also suitable for:

Microzotl2.0Microzotl2.0 deluxeMz2-s