1. Manuals
  2. Brands
  3. DeWalt Manuals
  4. Grinder
  5. DWE4100
  6. Manual

DeWalt DWE4100 Manual

Hide thumbs Also See for DWE4100:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
DWE4100
DWE4151
Final Page size: A5 (148mm x 210mm)

Advertisement

Table of Contents
loading

Related Manuals for DeWalt DWE4100

Summary of Contents for DeWalt DWE4100

  • Page 1 DWE4100 DWE4151 Final Page size: A5 (148mm x 210mm)
  • Page 2 English (original instructions) Copyright D WALT...
  • Page 3 Fig. A Fig. B1 Fig. B2...
  • Page 4 Fig. C Fig. D Fig. E1 Fig. E2 Fig. F...

  • Page 5: Technical Data

    English (original instructions) English ANGLE GRINDERS DWE4100, DWE4151 Congratulations! WARNING: To reduce the risk of injury, read the instruction manual. You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the Definitions: Safety Guidelines most reliable partners for professional power tool users.

  • Page 6: Personal Safety

    English refrigerators. There is an increased risk of electric shock if will do the job better and safer at the rate for which it your body is earthed or grounded. was designed. c ) Do not expose power tools to rain or wet conditions. b ) Do not use the power tool if the switch does not turn Water entering a power tool will increase the risk of it on and off.

  • Page 7: Causes And Operator Prevention Of Kickback

    English c ) Do not use accessories which are not specifically l ) Never lay the power tool down until the accessory designed and recommended by the tool has come to a complete stop. The spinning accessory manufacturer. Just because the accessory can be may grab the surface and pull the power tool out of your attached to your power tool, it does not assure safe control.
  • Page 8 English otherwise kickback may occur. Investigate and take snag the rotating accessory and cause loss of control or kickback. corrective action to eliminate the cause of wheel binding. e ) Do not attach a saw chain woodcarving blade or d ) Do not restart the cutting operation in the toothed saw blade.

  • Page 9: Package Contents

    English Residual Risks Intended Use The DWE4100 and DWE4151 heavy-duty angle grinders have In spite of the application of the relevant safety regulations been designed for professional grinding, sanding, wire brushing and the implementation of safety devices, certain residual risks and cutting applications.

  • Page 10: Accessories And Attachments

    When using the DWE4100 or the DWE4151 grinder for cutting 4. Close the guard latch to secure the guard on the gear case metal or masonry, a Type 1 guard MUST be used. Type 1 guards cover.

  • Page 11: Prior To Operation

    English Fitting and Removing a Grinding or Cutting 3. Place the rubber backing pad correctly onto the spindle   2  4. Place the sanding sheet on the rubber backing pad. Disc (Fig. A, D, E1, E2) 5. Screw the threaded clamp nut   5 ...

  • Page 12: Cutting Metal

    English workpiece or loss of control may create a hazard and activation of a ground fault interrupter, throwing of a cause personal injury. circuit breaker, accidental unplugging, or power failure. If the slider switch is locked on when the power is connected, •...

  • Page 13: Maintenance

    English Rough Grinding never use a cutting disc for roughing. Cleaning Always use the guard type 27. The best roughing results are achieved when setting the WARNING: Blow dirt and dust out of the main housing machine at an angle of 30° to 40°. Move the machine back and with dry air as often as dirt is seen collecting in and around forth with moderate pressure.
  • Page 14 English GRINDING AND CUTTING ACCESSORY CHART Guard Type Accessory Description How to Fit Grinder Depressed centre grinding disc TYPE 27 Type 27 guard gUARD Flap wheel Backing flange Type 27 depressed centre wheel Wire wheels Threaded clamp nut Wire wheels with threaded nut Type 27 guard Wire wheel...
  • Page 15 English GRINDING AND CUTTING ACCESSORY CHART (CONT.) Guard Type Accessory Description How to Fit Grinder Masonry cutting disc, bonded TYPE 1 Type 1 guard gUARD Metal Backing flange cutting disc, bonded Cutting wheel Diamond cutting Threaded clamp nut wheels TYPE 1 gUARD TYPE 27 gUARD...
  • Page 16 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België en Luxemburg Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)

This manual is also suitable for:

Dwe4151

Table of Contents