Advertisement
PRO2 mode setting
Digital dis-
play setting
function
Press
Turn
Digital dis-
play inver-
sion function
Turn
Turn
ECO mode
setting
function
PRO3 mode setting
Data bank
load setting
function
Press
Press
Turn
Data bank
save setting
function
Press
PRO4 mode setting
Data bank
load setting
function
Press
Press
Turn
Data bank
save setting
function
Press
Take care that if this product and the other digital fiber amplifiers are mounted in
cascade. The setting method is the same as well.
Press
Turn
Incident light intensity display
Percentage display
Peak hold display
Bottom hold display
Turn
Press
Turn OFF
Turn ON
Turn
Press
ECO OFF
ECO ON
Turn
1CH
Press
2CH
3CH
Cancel
Turn
1CH
Press
2CH
3CH
Cancel
Turn
1CH
Press
2CH
3CH
Cancel
Turn
1CH
Press
2CH
3CH
Cancel
PRO5 mode setting
The 0-ADJ setting function in this product was removed from production starting May, 2005.
Press
Turn
Notes: 1)
When any code other than the codes given in the code setting table below is used, ' - ' is
displayed.
The initial setting of the respose time for this product is 'H-SP', which is not in the code set-
ting table, as shown below. Thus, the factory setting is displayed as '
2)
When the code setting function is used, refer to the 'Code setting table' given below.
Press
Code setting table
1st figure
Direct
Response
Press
code
time
STD
H-02 (standard)
STD
H-03 (large)
STD
H-01 (small)
Press
LONG
H-02 (standard)
LONG
H-03 (large)
LONG
H-01 (small)
Press
FAST
H-02 (standard)
FAST
H-03 (large)
FAST
H-01 (small)
S-D
H-02 (standard)
Press
Press
3)
In order to change PRO mode setting to 'RUN' mode, press MODE key for 2 sec. or more.
4)
The response time 'H-SP' cannot be set by using the code setting function.
14
KEY LOCK FUNCTION
Press
If the jog switch and MODE key are pressed for more than 2 sec. at the same time
in 'RUN' mode condition, the key operations are locked, and only the threshold
value confirmation function or the adjust function (valid only when the adjust lock
function is canceled) is valid.
To cancel the lock function, press both the keys for more than 2 sec. once again.
Press
15
INTENDED PRODUCTS FOR CE MARKING
The models listed under '
As for all other models, please contact our office.
http://panasonic-electric-works.net/sunx
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
Europe Headquarter: Panasonic Electric Works Europe AG
Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany
Phone: +49-8024-648-0
US Headquarter: Panasonic Electric Works Corporation of America
629 Central Avenue New Providence, New Jersey 07974 USA
Phone: +1-908-464-3550
PRINTED IN JAPAN
Code
setting
function
Press
(Note 1)
: Select the
: Confirmed
Turn
desired code
Press
Turn
(Note 2)
Adjust lock
setting
function
Press
Adjust lock ON
Adjust lock OFF
Turn
Turn
Setting
reset
function
Press
Cancel
2nd figure
H y s t e-
Direct
L-ON/
Direct
Display
D-ON
resis
L-ON
digit
L-ON
Percent
L-ON
Peak hold
L-ON
Bottom hold
D-ON
digit
D-ON
Percent
D-ON
Peak hold
D-ON
Bottom hold
SPECIFICATIONS' come with CE Marking.
1
© Panasonic Electric Works SUNX Co., Ltd. 2010
Press
Press
(Blinking)
Press
Press
Press
Goes to 'RUN' mode
after blinking twice.
'.
3rd figure
4th figure
Adjust
Timer
Direct
Timer
operation
lock
ON
NON
OFF
ON
OFF-delay
1ms
ON
ON-delay
3ms
ON
ONE-SHOT
5ms
OFF
NON
10ms
OFF
OFF-delay
30ms
OFF
ON-delay
50ms
OFF
ONE-SHOT
100ms
300ms
500ms
1s
2s
3s
4s
5s
Advertisement
