Table of Contents
Advertisement
English
3. Press the Bluetooth® button
to put the unit into Bluetooth® (BT) mode. This will cause
the Bluetooth® button to blink slowly. During this time, the
radio is trying to find a previously paired device. If found the
Bluetooth® button will stay lit without any blinking.
4. If another device is to be paired, press the Bluetooth® button
and it should begin a fast blink pattern. While the radio is
displaying the fast blink, it is in paring mode.
5. Confirm pairing on your device. (Please consult your device's
instruction manual for specific pairing instructions.)
nOTE: If pairing is not confimed within 2 minutes, the LED
will stop flashing and the charger/radio will return to half
second interval blink pattern.
6. Once pairing is successful the Bluetooth® indicator/
button
13
will turn solid. The charger/radio will now play
music from your device.
Bluetooth® status indicator
lED indicator
status/Mode
Steady blinking (half
charger/radio is unpaired or in
second interval)
connecting mode.
Rapid Blinking
charger/radio is in pairing mode and
discoverable by your device.
Solid light
charger/radio is connected with
a device.
No light
charger/radio has timed out and/
or is off.
Connecting a Previously Paired Bluetooth® Audio Device
If a Bluetooth® device has been previously paired to the
charger/radio it should automatically reconnect when charger/
radio is powered on. After 4 seconds the charger/radio will
go into connecting mode. This is indicated by the Bluetooth®
indicator/button
13
blinking steady. Once the previously paired
Bluetooth® device is recognized and connected, the LED will go
solid. If connection does not occur and you are unable to stream
music please follow the instructions for Pairing Charger/radio
with a Bluetooth® Audio Device.
Timeout Functionality (Fig. A)
To conserve battery life the charger/radio is designed to power
off automatically after an hour of inactivity. This inactivity could
be due to the device being unpaired for an hour or in the case
of the Bluetooth® connection being broken for the same period
of time. If the charger/radio powers off due to inactivity of
any kind refer to Connecting a Previously Paired Bluetooth®
Audio Device.
nOTE: Optimum Bluetooth® streaming range is roughly 9 m
(line of sight) to the charger/radio but distances up to 30 m
are possible. Physical obstacles, other wireless devices or
electromagnetic devices may affect the connection quality.
If Bluetooth® connection is lost due to exceeding time of
separation, exceeding the optimum distance, obstacles or
otherwise, reconnecting your device with the charger/radio may
be necessary.
10
or use the mode button
13
Charging a Cell Phone or Audio Device Via
USB (Fig. A)
Your audio device or mobile phone can be charged (up to
2.1 AMPS) using the USB power port
This charging is possible when unit is on, running off of AC plug
power or the battery pack.
AC Outlets (Fig. A)
The charger radio is equipped with 2 AC outlets
maximum) for powering additional tools or appliances.
Factory Reset
A Factory Reset will remove all presets and restore the radio to
its default settings.
To perform a factory reset press Menu
to scroll to 'System'. Press Enter Display
keys
to scroll to 'Factory Reset'. Press Enter Display
5
Important Radio Notes
1. Reception will vary depending on location and strength of
radio signal.
2. Running the radio while connected to certain generators
may cause background noise.
MAINTENANCE
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
The charger and battery pack are not serviceable.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING: Shock hazard. Disconnect the charger/
radio from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non-metallic brush. Do not use water
or any cleaning solutions. Never let any liquid get inside
the unit; never immerse any part of the unit into a liquid.
16
on the charger/radio.
14
(10 amp
10
and use arrow keys
5
7
to select. Use arrow
to select.
7
Hide quick links:
Advertisement
Table of Contents
