Table of Contents
Advertisement
SJ-15 Series
Operator's Manual
WARNING:
This product can expose you to chemicals
State of California to cause cancer and birth defects or other
reproductive harm.
For more information about this regulation:
which are known
to the
www.P65Warnings.ca.gov
Automatic Parts Washer
MODELS:
For the Cuda Dealer nearest you,
consult our web page at
www.CudaUSA.com
9.801-128.0-V
Top-Load
1.043-458.0
1.043-459.0
1.043-460.0
1.043-461.0
1.043-462.0
1.043-463.0
08/14/19
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Kärcher CUDA SJ-15 Series
Summary of Contents for Kärcher CUDA SJ-15 Series
- Page 1 SJ-15 Series Operator’s Manual Automatic Parts Washer Top-Load MODELS: 1.043-458.0 1.043-459.0 1.043-460.0 1.043-461.0 1.043-462.0 1.043-463.0 For the Cuda Dealer nearest you, consult our web page at WARNING: www.CudaUSA.com This product can expose you to chemicals which are known to the State of California to cause cancer and birth defects or other reproductive harm.
-
Page 2: Machine Data Label
Machine Data Label Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 3: Table Of Contents
Detail Brush ......34 Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 4: How To Use This Manual
KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts. NOTE: The manual part number is located on the lower right corner of the front cover. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 5: Safety
When ordering parts, please specify model and serial number. Use only identical replacement parts. This machine is to be used only by trained operators. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 6: General Safety Information
Before servicing the machine, refer to all safety l'essence minérale, etc. Drainer les pièces à data sheets (SDS’s) on the material identified in nettoyer de toute substance combustible ou the waste stream. You must comply with all Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... - Page 7 This automatic parts washer is designed to operate safely and efficiently. Before you begin to install and use the machine, please familiarize yourself with the major components. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V...
-
Page 8: Operations
240 Volts 480 Volts Kw Rating Output KW of Heater When Operated On of Heater Volts Volts Volts Volts Volts Volts Volts 3.78 4.13 3.38 3.78 4.14 3.78 4.14 4.20 4.59 6.30 6.89 Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... - Page 9 Kilowatt Hours to Heat Water Amount of Liquid Temperature Rise °F 20° 40° 60° 80° 100° 120° 140° Cu.Ft. Gal. Kilowatts to heat in one hour 10.7 12.8 11.2 10.7 12.0 14.5 13.4 16.7 Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V...
-
Page 10: Component Identification
Operations Component Identification Parts Basket Water Tank Wash Timer Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 11: Installation
Electrical ......Refer to Serial Plate located on rear of electrical box Cabinet Dimensions ... SJ-15: 48” W x 49” H x 46” D (121.92 cm x 124.46 cm x 116.84 cm) Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 12: Pre-Start Checklist
Fill until low water light goes out. NOTE: Detergent must be thoroughly mixed before adding to tank. To ensure detergent mixes properly and does not foam, make sure machine is up to operating temperature before adding any detergent. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 13: Using The Oil Skimmer System
Water will flow off the blades in droplets. Once droplets begin to flow off the wiper blades, stop the skimmer motor. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 14: Maintenance
The spin pin o-rings should be replaced annually. Filters With the tank empty, clean the suction pump strainer. Clean when pressure gauge reads a 10 PSI decrease from start up pressure. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 15: Water Level
(See Detergents and Additives). Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 16: Options
Assy. Gauge 8.725-276.0 9.804-631.0 Waste Water Drum Evaporator Automatic 8.707-034.0 Water Fill 8.725-284.0 Oil Decanter Bucket 8.913-702.0 Mild Steel Temperature Gauge 8.712-156.0 Timer (Reversed View) 8.725-283.0 Hour Meter 9.802-283.0 Caster Wheels 8.725-280.0 Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 17: Automatic Water Fill
Tool and align the other spin pin as described in step 2. Spin Pin 4. The alignment tool should move freely from one Spin Pin spin pin onto the other spin pin. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 18: Troubleshooting
See wiring instructions. AND OVERLOAD Check lid safety switch for proper depres- KICKS OFF Pump cycles too frequently sion. Readjust if needed for proper opera- tion. Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... -
Page 19: Parts
No power to parts washer Check circuit breaker supplying power to washer. VOLTAGE Fuse blown on transformer Replace fuse. LIGHT FAILS TO COME ON Transformer defective Replace transformer Cuda SJ-15 Series Operator’s Manual 9.801-128.0 - V... - Page 20 9.801-128.0 • Printed in U.S.A.
Need help?
Do you have a question about the CUDA SJ-15 Series and is the answer not in the manual?
Questions and answers