Advertisement
Quick Links
Astronomical/annual time switch
AstroRex DY64
0047 70 /74
! Safety notes
This product may be installed only by a qualified electrician. Non-compliance may result in a fire hazard or electric shocks. Before installati-
on, read the operating instructions and observe the product-specific requirements for the installation location. Use only original spare parts for repair and mainte-
nance. All Legrand products may be opened and repaired only by specially trained Legrand personnel. Unauthorised opening and repair by other persons will invali-
date all claims for liability, replacement or warranty services. When operated from the mains voltage, the time switch may not be used to switch safe extra-low voltages
(SELV). When The device contains a Li-SOCl2 cell. When the product reaches the end of its life, this cell must be correctly removed and disposed of in accordance
with national legislation and the requirements of environmental protection.operated from a safe extra-low voltage, it may not be used to switch mains voltages.
Channel number
Function
Menu selection, back in menu,
Actuation >1s = operating display
• Selection of a menu item or set a parameter.
• Channel selection
Overview
Technical data
Supply voltage:
Power consumption:
Relay outputs 1- 4:
Accuracy:
Wire cross-sections:
Programs
Control signal for channel 1:
Control-pulse duration:
Control-wire length:
Rated impulse voltage
One-week overview of the
programmed switching times.
Resolution: 0.5 h
Switch state
Day, time, date
Confirm a selection or accept
a parameter setting
R
3600W
1800W
0047 70
0047 74
120 / 230V 50/60Hz
24 AC/DC
approx. 0,3...2 W
approx. 3...4 W
4 changeover contacts 16A 250V~ cos ϕ = 1
± 0,2 s/day under typical installation conditions
single-strand
multi-strand
1,5...4 mm
1,5...2,5 mm
2
4 channels x 3 program types x 28 programs
supply voltage, referred to neutral
> 200ms
max. 50m
4 kV
0,33 kV
Lithium battery module
Ref. 0047 82
047 70
120V/230V 50/60Hz
M
˜
R6a -20T
Socket for
data key
Ref. 0047 81
120V/230V~50/60Hz
Separate
L
N S >1
manual switch
M
˜
for each
channel
+
1800W
100W
1800W
Delay time:
Local coordinates:
Battery reserve:
Storage temperature:
Operating principle:
Operation in a normal environment
2
Degree of contamination:
Installation:
1
4
2
1
4
2
1
2
ON
ON
AUTO
AUTO
OFF
OFF
+
3
4
ON
ON
AUTO
AUTO
OFF
OFF
2
1
4
1
4
2
3
4
+
+
2300W
1400VA
0 ... 23 h 59 min 59 s
Resolution 1°
5 years
- 20°C to +60°C
Typ 1.B. S. T. IEC/EN 60730-2-7
2
in distribution panel
®
GB
c
1x 58W 7µF
Advertisement
Related Manuals for LEGRAND LEXIC AstroRex DY64
Summary of Contents for LEGRAND LEXIC AstroRex DY64
- Page 1 Use only original spare parts for repair and mainte- nance. All Legrand products may be opened and repaired only by specially trained Legrand personnel. Unauthorised opening and repair by other persons will invali- date all claims for liability, replacement or warranty services.
- Page 2 General information • Starting: After connection of the supply voltage, the clock starts to run with the last selected function. The relay position is determined by the currently active program. • Backup battery operation mode: - background lighting not available. - data key READ/WRITE only via the menu.
- Page 3 PROGRAM / WEEK This menu item is provided for the simple input of programs which are to be repeated weekly (such as switching of lights and boilers). A weekly program consists of an ON time, an OFF time and the associated ON and OFF days. •...
- Page 4 PROGRAM / EXCEPTION The weekly and annual programs defined for a channel are not executed as long as an extra program is active. However, other exception programs will be executed while an exception program is active. The various exception programs are ORed together as described above. (see OR function 3a) •...
- Page 5 Required inputs, depending on the program type and menu options. ON/OFF Weekday assi- Active period Active period Char- Prog- Exe- Application, objectives, examples times gnments START date END date acte- cution ristics type The same switching cycle is to be executed on every day of MON TO each week.
- Page 6 ON/OFF Weekday assi- Active peri- Active peri- Char- Program Execution Application, objectives, examples acte- times gnments type START date END date ristics An exception program is to completely replace any existing Day, month, Day, month, weekly or annual program on each day during a specific period - - - - - - - - MON TO...
- Page 7 Select the option PROGRAM / WEEK for a program which is to be executed a on specific days of the week and is to be repeated weekly. Select the option PROGRAM / YEAR for a program which is to be executed each year or only in a specific year. The execution period within the year can be defined by entering start and end dates.
-
Page 8: Operating Hours Counter
Operating-hours counter This displays the total duration of the ON times, from 0 to 065535 hours, and the date on which this counter was last reset. Contrast adjustment 1 h-Test If this menu item is activated, the outputs are switched on for one hour. The test can be terminated at any time by selecting the option PASSIVE. - Page 9 Control input with delaytime The control signal affects only channel 1 and overrides all program settings for this channel (OR function). Channel 1 remains switched on as along as the control signal is present. If the function CYCLE is selected under SETUP, channel 1 is switched on and off cyclically. When the control signal is switched off, the output of channel 1 switches off after the defined delaytime, unless one of the programs for this channel specifies otherwise.
- Page 10 Extended Settings The data interface KEY is preset and cannot be changed. without function Activating and deactivating mains synchronisation. The default setting is PASSIVE. In order to improve the long-term accuracy, it is advisable to activate synchronisation on 50/60 Hz mains with frequency adjustment.