Download  Print this page

Craftsman 125.46569 Operator's Manual

20v max* lithium-ion cordless circular saw.
Hide thumbs

Advertisement

OPERATOR'S MANUAL
MANUAL DEL USUARIO
20V MAX* LITHIUM-ION
CORDLESS CIRCULAR SAW
20 V MÁX* DE IONES DE LITIO
SIERRA CIRCULAR INALÁMBRICA
Model
No. 125.46569
Número de modelo. 125.46569
WARNING:
the Operator's Manual before using this product.
ADVERTENCIA:
comprender el manual antes de utilizar este producto.
Sears Brands Management Corporation, Hoffman Estates, IL 60179 USA
Save this manual for future reference.
Conserve este manual para futura referencia.
* Maximum initial battery voltage (measured without workload) is 20 volts.
Nominal working voltage is 18 volts.
* La tensión inicial máxima de la batería (medida sin carga) es 20 voltios.
La tensión de trabajo nominal es 18 voltios.
To reduce the risk of injury, the user must read and understand
Para reducir el riesgo de lesiones, el usuario debe leer y

Advertisement

Table of Contents

   Related Manuals for Craftsman 125.46569

   Summary of Contents for Craftsman 125.46569

  • Page 1 CORDLESS CIRCULAR SAW 20 V MÁX* DE IONES DE LITIO SIERRA CIRCULAR INALÁMBRICA Model No. 125.46569 Número de modelo. 125.46569 WARNING: To reduce the risk of injury, the user must read and understand the Operator’s Manual before using this product. ADVERTENCIA: Para reducir el riesgo de lesiones, el usuario debe leer y comprender el manual antes de utilizar este producto.
  • Page 2: Table Of Contents

    ■ Lista de piezas, ilustrada......19 ■ Figure Numbers (Illustrations) ......i-v ■ Números de las figuras (ilustraciones)....i-v CRAFTSMAN LIMITED WARRANTY FOR ONE YEAR from the date of sale this power tool is warranted against defects in material or workmanship.
  • Page 3: Safety Instructions

    POWER TOOL USE AND CARE ■ When operating a power tool outdoors, ■ Use only with compatible Craftsman 20V use an extension cord suitable for outdoor Max powered by DieHard slide-type lithium- use. Use of a cord suitable for outdoor use ion battery packs.
  • Page 4 SAFETY INSTRUCTIONS does not turn it on and off. Any power tool or performing maintenance. Following that cannot be controlled with the switch is this rule will reduce the risk of serious dangerous and must be repaired. personal injury. ■ Disconnect the plug from the power source ■...
  • Page 5 SAFETY INSTRUCTIONS the workpiece to a stable platform. It is hold the saw motionless in the material until important to support the workpiece properly the blade comes to a complete stop. Never to minimize body exposure, blade binding, attempt to remove the saw from the work or or loss of control.
  • Page 6: Safety Instructions

    SAFETY INSTRUCTIONS deposits, or a build-up of debris. ■ Under extreme usage or temperature ■ Lower guard should be retracted manually conditions, battery leakage may occur. If only for special cuts such as “plunge cuts” liquid comes in contact with your skin, wash and “compound cuts”.
  • Page 7: Symbols

    SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes C urrent Hertz Frequency (cycles per second)
  • Page 8: Símbolos

    SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation, which, if not DANGER avoided, will result in death or serious injury. Indicates a potentially hazardous situation, which, if not WARNING avoided, could result in death or serious injury.
  • Page 9: Features

    FEATURES PRODUCT SPECIFICATIONS Circular Saw Model No........................125.46569 Type....................Cordless, battery-powered Motor........................20 V max* d.c. Blade Diameter.......................6-1/2 in. Blade Arbor........................5/8 in. Maximum Cutting Depth at 0°....................2 in. Maximum Cutting Depth at 45°..................1-1/3 in. No Load Speed......................3300 rpm Weight (with included battery)...................6.8 lbs...
  • Page 10: Assembly

    ASSEMBLY WARNING: UNPACKING If any parts are broken or This product requires assembly. missing, do not attempt to attach the battery pack or operate the tool until the broken or ■ Carefully remove the product and any missing parts are replaced. Failure to do so accessories from the box.
  • Page 11: Operation For Circular Saw

    OPERATION FOR CIRCULAR SAW This product will accept compatible Craftsman with the blade guard, while thicker blades will 20V Max powered by DieHard slide-type prevent blade screw from securing blade on lithium-ion battery packs. For complete charging spindle. Either of these situations could result instructions, refer to the Operator's Manual for in a serious accident.
  • Page 12: Funcionamiento De La Sierra Circular

    OPERATION FOR CIRCULAR SAW WARNING DANGER: : Blade teeth are sharp and Release switch immediately can cut fingers if touched. if blade binds or saw stalls. Kickback could cause you to lose control of the saw. Loss of ■ Release the lower blade guard lever to control can lead to serious injury.
  • Page 13 OPERATION FOR CIRCULAR SAW if they are not kept clean, sharp, and properly normal operating condition. If it does not set. Using a dull blade will place a heavy correct a slow or sluggish closing lower load on the saw and increase the danger of guard, do not use the saw.
  • Page 14 OPERATION FOR CIRCULAR SAW ■ Loosen the depth adjustment knob. CROSS CUTTING/RIP CUTTING ■ Determine the desired depth of cut. See Figure 15, page iv ■ Locate the depth of cut guide on back of When making a cross cut or rip cut, align the upper blade guard.
  • Page 15 OPERATION FOR CIRCULAR SAW BEVEL CUTTING can result in loss of control of the saw possibly causing serious injury. See Figures 19 - 20, page v ■ Align the line of cut with the inner blade guide notch on the base when making 45° ■...
  • Page 16: Operation For Circular Saw

    OPERATION FOR CIRCULAR SAW ADJUSTING POSITIVE 0° BEVEL STOP To adjust positive 0° bevel stop: ■ Remove the battery pack from the saw. WARNING: Before performing any ■ Loosen the bevel adjustment knob. adjustment, make sure the battery pack ■ Loosen the hex nut securing the adjustment is removed from tool.
  • Page 17: Care & Maintenance

    CARE & MAINTENANCE WARNING: safety and reliability, all repairs should be When servicing, use only identical replacement parts as listed in this performed by a qualified service technician. manual. Use of any other parts may create a hazard or cause product damage. STORAGE ■...
  • Page 18: Troubleshooting

    TROUBLESHOOTING PROBLEM CAUSE SOLUTION The battery is defective. Replace with a new, charged battery. Tool will not turn on. The switch is dead. Tool must be replaced. Brushes are worn out. Tool must be replaced. Check the blade and replace with a Worn/damaged saw blade.
  • Page 19: Illustrated Parts List

    CRAFTSMAN 20V MAX* LITHIUM-ION CORDLESS CIRCULAR SAW-MODEL NUMBER 125.46569 The model number will be found on a label attached to the motor housing. TO PURCHASE REPLACEMENT PARTS, CALL 1-888-331-4569 ITEM NO. PART NO. DESCRIPTION Circular Saw Tool Body 125.CC20A-B Flange Set...
  • Page 20: Resolución De Problemas

    See this section for all of the figures referenced in the Operator's Manual. (Consulte esta sección para ver todas las figuras mencionadas en el manual del usuario.) Fig. 1 A. Bevel Adjustment Knob (Perilla de ajuste de bisel) B. Spindle Lock Button (Botón de bloqueo del husillo) C.
  • Page 21 Fig. 2 Fig. 3 A. Battery Pack (not included) (Paquete de baterías (no incluido)) A. Spindle Lock Button (Botón de bloqueo del husillo) B. To install (Para instalación) B. Lower Blade Guard (Protección de la hoja inferior) C. Depress Battery Release Button to remove C.
  • Page 22 Fig. 7 Fig. 8 CORRECT SUPPORT SOPORTE CORRECTO CORRECT BLADE DEPTH SETTING = BLADE EXPOSED 1/4 in. (6.35MM) OR LESS ON UNDERSIDE OF WORKPIECE CONFIGURACIÓN DE PROFUNDIDAD DE LA HOJA CORRECTA = HOJA EXPUESTA DE 1/4 pulg. (6,35 MM) O MENOS EN EL EXTERIOR DE LA PIEZA DE TRABAJO Fig.
  • Page 23 Fig. 13 Fig. 14 WRONG (INCORRECTO) TOP VIEW OF SAW Fig. 15 Fig. 16 VISTA SUPERIOR DE LA SIERRA A. Blade Guide Notch (Muesca de la guía de la hoja de sierra) A. Straight Edge (Borde recto) B. Guideline (Línea de la guía) B.
  • Page 24 Fig. 20 Fig. 19 A. Bevel Adjustment Knob (Perilla de ajuste de bisel) B. Bevel Guide (Guía del bisel) C. Blade Guide Notch (Muesca de la guía de la hoja de sierra) D. Guideline (Línea de la guía) E. Motor Housing (Carcasa del motor) A.

Comments to this Manuals

Symbols: 0
Latest comments: