Table of Contents
Advertisement
Quick Links
P.O. BOX 265
OGDENSBURG, NY
U.S.A. 13669-0265
A V T E C H
TEL: 888-670-8729 (USA & Canada) or +1-613-686-6675 (Intl)
FAX: 800-561-1970 (USA & Canada) or +1-613-686-6679 (Intl)
info@avtechpulse.com
INSTRUCTIONS
MODEL AVMH-1A-C
10 VOLTS, 25 MHz
IMPULSE GENERATOR
WITH 130 – 250 ps PULSE WIDTH
SERIAL NUMBER: ____________
E L E C T R O S Y S T E M S
N A N O S E C O N D
W A V E F O R M
S I N C E
-
http://www.avtechpulse.com/
E L E C T R O N I C S
1 9 7 5
BOX 5120, LCD MERIVALE
X
OTTAWA, ONTARIO
CANADA K2C 3H5
L T D .
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Avtech AVMH-1A-C
Summary of Contents for Avtech AVMH-1A-C
- Page 1 BOX 5120, LCD MERIVALE OGDENSBURG, NY FAX: 800-561-1970 (USA & Canada) or +1-613-686-6679 (Intl) OTTAWA, ONTARIO U.S.A. 13669-0265 CANADA K2C 3H5 info@avtechpulse.com http://www.avtechpulse.com/ INSTRUCTIONS MODEL AVMH-1A-C 10 VOLTS, 25 MHz IMPULSE GENERATOR WITH 130 – 250 ps PULSE WIDTH SERIAL NUMBER: ____________...
-
Page 2: Warranty
Avtech product is found to be defective, Avtech shall at its option repair or replace said defective item. This warranty does not apply to units which have been dissembled, modified or subjected to conditions exceeding the applicable specifications or ratings. -
Page 3: Table Of Contents
TABLE OF CONTENTS WARRANTY........................2 TECHNICAL SUPPORT....................2 TABLE OF CONTENTS....................3 INTRODUCTION.......................5 AVAILABLE OPTIONS......................5 SPECIFICATIONS......................6 REGULATORY NOTES.....................7 FCC PART 18.......................... 7 EC DECLARATION OF CONFORMITY...................7 DIRECTIVE 2002/95/EC (RoHS).....................8 DIRECTIVE 2002/96/EC (WEEE)....................8 AC POWER SUPPLY REGULATORY NOTES................9 INSTALLATION.......................10 VISUAL CHECK........................10 POWER RATINGS......................... 10 CONNECTION TO THE POWER SUPPLY................10 PROTECTION FROM ELECTRIC SHOCK................11 ENVIRONMENTAL CONDITIONS..................12... - Page 4 PCB 158P - LOW VOLTAGE POWER SUPPLY, 1/3.............25 PCB 158P - LOW VOLTAGE POWER SUPPLY, 2/3.............26 PCB 158P - LOW VOLTAGE POWER SUPPLY, 3/3.............27 MAIN WIRING........................28 PERFORMANCE CHECK SHEET.................29 Manual Reference: /fileserver2/officefiles/instructword/avmh/AVMH-1A-C,ed1.odt. Last modified May 22, 2015. Copyright © 2015 Avtech Electrosystems Ltd, All Rights Reserved.
-
Page 5: Introduction
INTRODUCTION The AVMH-1A-C is a high performance instrument capable of generating up to 10V into 50Ω loads at repetition rates up to 25 MHz. The output pulse width may be adjusted from < 130 ps to > 250 ps. Instruments with the "-P" model suffix can generate up to +10V, whereas instruments with the "-N"... -
Page 6: Specifications
For DC offset option add suffix -OS. A 50 Ohm load is required. Other loads may damage the instrument. Consult Avtech (info@avtechpulse.com) if you need to drive other load impedances. For operation at amplitudes of less than 20% of full-scale, best results will be obtained by setting the amplitude near full-scale and using external attenuators on the output. -
Page 7: Regulatory Notes
If interference is observed, check that appropriate well-shielded cabling is used on the output connectors. Contact Avtech (info@avtechpulse.com) for advice if you are unsure of the most appropriate cabling. Also, check that your load is adequately shielded. It may be necessary to enclose the load in a metal enclosure. -
Page 8: Directive 2002/95/Ec (Rohs)
Directive 2002/96/EC categories 1-7 and 10, as stated in the "Article 2 - Scope" section of Directive 2002/95/EC. DIRECTIVE 2002/96/EC (WEEE) European customers who have purchased this equipment directly from Avtech will have completed a “WEEE Responsibility Agreement” form, accepting responsibility for WEEE compliance (as mandated in Directive 2002/96/EC of the European Union and local laws) on behalf of the customer, as provided for under Article 9 of Directive 2002/96/EC. -
Page 9: Ac Power Supply Regulatory Notes
AC POWER SUPPLY REGULATORY NOTES This instrument converts the AC input power to the +24V DC voltage that powers the internal circuitry of this instrument using a Tamura AAD130SD-60-A switching power supply. According to the manufacturer, the Tamura AAD130SD-60-A has the following certifications: UL60950-1 IEC60950 -1... -
Page 10: Installation
INSTALLATION VISUAL CHECK After unpacking the instrument mainframe and the transformer module, examine to ensure that they have not been damaged in shipment. Visually inspect all connectors, knobs, and handles. Confirm that a power cord and an instrumentation manual (this manual), are with the instrument. -
Page 11: Protection From Electric Shock
5. Do not attempt any repairs on the instrument, beyond the fuse replacement procedures described in this manual. Contact Avtech technical support (see page 2 for contact information) if the instrument requires servicing. Service is to... -
Page 12: Environmental Conditions
ENVIRONMENTAL CONDITIONS This instrument is intended for use under the following conditions: 1. indoor use; 2. altitude up to 2 000 m; 3. temperature 5 °C to 40 °C; 4. maximum relative humidity 80 % for temperatures up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C;... -
Page 13: Fuses
FUSES This instrument contains four fuses. All are accessible from the rear-panel. Two protect the AC prime power input, and two protect the internal DC power supplies. The locations of the fuses on the rear panel are shown in the figure below: Fuses #1 and #2 Fuse #4 Fuse #3... -
Page 14: Dc Fuse Replacement
DC FUSE REPLACEMENT The DC fuses may be replaced by inserting the tip of a flat-head screwdriver into the fuse holder slot, and rotating the slot counter-clockwise. The fuse and its carrier will then pop out. FUSE RATINGS The following table lists the required fuses: Recommended Replacement Part Nominal Fuses... -
Page 15: Front Panel Controls
FRONT PANEL CONTROLS 1. POWER Switch. This is the main power switch. 2. OVERLOAD Indicator. When the instrument is powered, this indicator is normally green, indicating normal operation. If this indicator is yellow, an internal automatic overload protection circuit has been tripped. If the unit is overloaded (by operating at an exceedingly high duty cycle or by operating into a very low impedance), the protective circuit will disable the output of the instrument and turn the indicator light yellow. - Page 16 4. DELAY Control. Controls the relative delay between the reference output pulse provided at the SYNC output and the main output. This delay is variable over the range of 0 to 50 ns, approximately. At high frequencies, this delay should be kept nearly fully counter-clockwise, so that the delay does not exceed the period (otherwise, the triggering may stop).
-
Page 17: Rear Panel Controls
REAR PANEL CONTROLS 1. AC POWER INPUT. An IEC-320 C14 three-pronged recessed male socket is provided on the back panel for AC power connection to the instrument. One end of the detachable power cord that is supplied with the instrument plugs into this socket. -
Page 18: General Information
GENERAL INFORMATION BASIC TEST ARRANGEMENT The AVMH-1A-C should be tested with a sampling oscilloscope with a bandwidth of at least 15 GHz to properly observe the high-speed waveform. A typical test arrangement is shown below: SAMPLING AVTECH OSCILLOSCOPE PULSER BW > 15 GHz... -
Page 19: Amplitude Interaction
VARIABLE MAIN OUTPUT Figure A The AVMH-1A-C can also be triggered by a TTL-level pulse applied to the TRIG input. AMPLITUDE INTERACTION Some properties of the output pulse may change as a function of the amplitude setting. For some demanding applications, it may be desirable to use a combination of external attenuators and the amplitude pot to achieve the desired output amplitude. -
Page 20: Minimizing Waveform Distortions
PREVENTING DAMAGE The AVMH-1A-C may fail if triggered at a PRF greater than 25 MHz. This unit is designed to operate into a load impedance of 50 Ohms and the output stage will be damaged if it is operated into an open circuit (or any other high impedance). -
Page 21: Options
OPTIONS The AVMH-1A-C is available with these options: -OS OPTION This option allows an externally generated DC offset to be added to the output. The desired DC offset is applied to the back panel OS terminal, which is connected to the output centre conductor trhough a high-quality RF inductor. -
Page 22: Mechanical Information
There are no user-adjustable internal circuits. For repairs other than fuse replacement, please contact Avtech (info@avtechpulse.com) to arrange for the instrument to be returned to the factory for repair. Service is to be performed solely by qualified service personnel. -
Page 23: Maintenance
MAINTENANCE REGULAR MAINTENANCE This instrument does not require any regular maintenance. On occasion, one or more of the four rear-panel fuses may require replacement. All fuses can be accessed from the rear panel. See the “FUSES” section for details. CLEANING If desired, the interior of the instrument may be cleaned using compressed air to dislodge any accumulated dust. -
Page 24: Wiring Diagrams
WIRING DIAGRAMS WIRING OF AC POWER M a in s c i r c u it s - h a z a r d o u s li v e . D o n o t a t te m p t a n y r e p a i r s o n t h i s i n s t r u m e n t b e y o n d t h e f u s e r e p la c e m e n t p r o c e d u r e s d e s c r i b e d i n t h e m a n u a l . -
Page 25: Pcb 158P - Low Voltage Power Supply, 1/3
PCB 158P - LOW VOLTAGE POWER SUPPLY, 1/3 X 1 3 6 - 3 2 1 / 4 " S S S C R E W , 0 6 0 4 M P P 1 8 8 6 - 3 2 S S E X T T O O T H W A S H E R , 0 6 W E 1 8 8 X 1 4 6 - 3 2 1 / 4 "... -
Page 26: Pcb 158P - Low Voltage Power Supply, 2/3
PCB 158P - LOW VOLTAGE POWER SUPPLY, 2/3 F U S E H O L D E R X 2 1 P C B 1 5 8 A L , V 2 B R A C K E T 6 4 0 4 4 5 - 6 T P 6 T P 3 T E S T - L O O P... -
Page 27: Pcb 158P - Low Voltage Power Supply, 3/3
PCB 158P - LOW VOLTAGE POWER SUPPLY, 3/3 R 2 1 1 . 5 K O Y C A P B A N K R 2 6 1 5 K C 2 3 1 0 0 0 u F / 3 5 V L E D H V W A R N I N G R 1 7... -
Page 28: Main Wiring
C = HIGH F RE Q SC ALE (AD JU ST S O V T R A T MAX A MP = -6V IN 25 MH z R AN GE ) Pri nte d Re vis i on 22-May-2015 CL 8 - 2 1 9 E Z:\mjcfiles\circuits\avmh\avmh.Ddb - AVMH-1A-C\AVM H-1A-C v2.s ch... -
Page 29: Performance Check Sheet
PERFORMANCE CHECK SHEET...
Need help?
Do you have a question about the AVMH-1A-C and is the answer not in the manual?
Questions and answers