SawStop TSA-SA70 Owner's Manual
  1. Manuals
  2. Brands
  3. SawStop Manuals
  4. Indoor Furnishing
  5. TSA-SA70
  6. Owner's manual

SawStop TSA-SA70 Owner's Manual

Large sliding table
Hide thumbs Also See for TSA-SA70:
Table of Contents

Advertisement

Quick Links

Download this manual
LARGE SLIDING TABLE
OWNER'S MANUAL
MODEL TSA-SA70
Note: A typical assembly takes 5-10 hours.
Please set aside sufficient time to complete
the assembly process in 1-2 sessions.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TSA-SA70 and is the answer not in the manual?

Questions and answers

Related Manuals for SawStop TSA-SA70

Summary of Contents for SawStop TSA-SA70

  • Page 1 LARGE SLIDING TABLE OWNER’S MANUAL MODEL TSA-SA70 Note: A typical assembly takes 5-10 hours. Please set aside sufficient time to complete the assembly process in 1-2 sessions.
  • Page 2 The saw shown on the front cover is the Industrial Cabinet Saw, Model ICS. Your saw may look different. SawStop, the SawStop blade logo, and the configuration of this product are either registered trademarks or trademarks of SawStop, LLC. Software copyright by...
  • Page 3 TO OUR CUSTOMERS Thank you for purchasing the SawStop Large Sliding Table. We are confident you will be pleased with its quality and performance. This manual tells you more about your large sliding table and how to operate and maintain it.
  • Page 4 HOW TO GET HELP Missing Parts? Have Questions? Our technical support team is standing by M-F, 6:30am-5pm PST to help with whatever you need. Give us a call at 503.582.9934 Email us at SERVICE@SAWSTOP.COM...

  • Page 5: Table Of Contents

    TABLE OF CONTENTS Product Specs................. Parts Inventory................. Parts & Hardware Lists..................... Tools Needed......................Getting to Know Your Large Sliding Table........Components......................Mounting Options..................... Front Mounting WITHOUT Left Wing............Center Mounting WITHOUT Left Wing............Rear Mounting WITHOUT Left Wing............. Front Mounting WITH Left Wing..............Center Mounting WITH Left Wing..............
  • Page 6 TABLE OF CONTENTS Installing the Guide Bearing Assembly..............Setting the Bearing Tension..................Installing the Angle Guide Rail................. Installing the Crosscut Fence Assembly..............Traditional Configuration................Crosscut Fence Assembly Configurations............... Euro Configuration..................Storage......................Installing the Logo Plate................... Adjustments..................Leveling........................Installing the Remaining Support Leg..............Aligning to the Blade....................

  • Page 7: Product Specs

    PRODUCT SPECIFICATIONS The SawStop Large Sliding Table is engineered for the demands of the Industrial woodshop and ensures precise, repeatable operation. This Sliding Table makes cutting sheet goods and larger stock easy, with maximum control and sure measurement. A rigid steel frame and 14 sealed, steel bearings ensure a reliable, smooth glide, and adjustability affords both traditional and Euro configurations for a maximum crosscut of 70”.

  • Page 8: Parts Inventory

    Certain components may have been pre-installed for shipping purposes. Parts Box (Labeled 2 of 2) Inner Guide Tube (Qty. 1) Outer Guide Tube (Qty. 1) Crosscut Fence (Qty. 1) Guide Rail (Qty. 1) Mounting Bracket (Qty. 1) TSA-SA70 OWNER’S MANUAL...
  • Page 9 Flip Stop (Qty. 1) Positioning Plate (Qty. 1) Miter Lock Assembly (Qty. 1) Front Guide Bracket (Qty. 1) Fence Extension (Qty. 1) Support Tube (Qty. 1) Logo Plate (Qty. 1) Cross Brace (Qty. 3) Sliding Table (Qty. 1) TSA-SA70 OWNER’S MANUAL...
  • Page 10 Hardware Pack TSA-SA70 OWNER’S MANUAL...
  • Page 11 M8 Lock Nut (x2) Self-tapping Screw (x2) M5 x 16 Washer (x2) Pack 6: Installing the Cross Braces/ Installing the Support Legs M8 x 16 Shoulder Bolt (x12) M8 Hex Cap Nut (x12) M8 x 16 Washer (x12) TSA-SA70 OWNER’S MANUAL...

  • Page 12: Tools Needed

    Rip fence or straight edge at least 30” long 8mm wrench • • Level 3/4” socket • • Square 13mm wrench (x2) • • Tape measure or calipers 12mm wrench • • Phillips head screwdriver Small socket extension • • Needle nose pliers Flashlight TSA-SA70 OWNER’S MANUAL...

  • Page 13: Getting To Know Your Large Sliding Table

    Outer Guide Tube Crosscut Fence Guide Rail Mounting Bracket Support Leg Leg Bracket Stepped Leg Bracket Positioning Plate Front Guide Bracket Support Tube Cross Brace Sliding Table Fence Pivot Assembly Flip Stop Miter Lock Assembly Fence Extension Logo Plate TSA-SA70 OWNER’S MANUAL...

  • Page 14: Mounting Options

    Mounting Options The SawStop Large Sliding Table can be mounted to your SawStop table saw in any of six different table orientations and three fence positions. Fence Positions: 90° Euro: 90° Traditional: 45° Traditional: Provides the Large Positions the fence at Use traditional Sliding Table’s...

  • Page 15: Front Mounting Without Left Wing

    The ripping length with the crosscut fence in the traditional configuration is reduced from 49” to 37.5”. 45° Traditional Mounts Center of 90° Traditional Saw Cabinet TSA-SA70 OWNER’S MANUAL...

  • Page 16: Rear Mounting Without Left Wing

    45° Traditional Mounts Forward of Saw Cabinet 90° Traditional TSA-SA70 OWNER’S MANUAL...

  • Page 17: Center Mounting With Left Wing

    Euro configuration Mounts while also maintaining the Rear of additional support to the left Saw Cabinet of the blade provided by the left extension wing. 45° Traditional 90° Traditional TSA-SA70 OWNER’S MANUAL...

  • Page 18: Modifying Your Table Saw

    Some of the steps below involve removing/installing your rails, switchbox, and extension wing. For those steps, please refer to your table saw manual and fence manual. (You can download copies of your manuals at www.sawstop.com.) DISCONNECT YOUR TABLE SAW FROM ELECTRICAL POWER BEFORE BEGINNING ANY MODIFICATIONS.

  • Page 19: Installing Your Large Sliding Table

    USING OTHER TYPES OF SAWS (SUCH AS A CIRCULAR SAW) CAN GENERATE ENOUGH HEAT TO BLISTER THE POWDER COATING. IT IS STRONGLY SUGGESTED THAT YOU USE A METAL CUTTING BAND SAW OR A HACK SAW WITH A METAL CUTTING BLADE ONLY. TSA-SA70 OWNER’S MANUAL...
  • Page 20 If necessary, complete the assembly of your saw then re-install the front and rear rails and the main tube (refer to your saw and fence manuals). When finished, continue to page 17. ⁄ ” TSA-SA70 OWNER’S MANUAL...

  • Page 21: Shortening The Rails Without The Extension Wing

    USING OTHER TYPES OF SAWS (SUCH AS A CIRCULAR SAW) CAN GENERATE ENOUGH HEAT TO BLISTER THE POWDER COATING. IT IS STRONGLY SUGGESTED THAT YOU USE A METAL CUTTING BAND SAW OR A HACK SAW WITH A METAL CUTTING BLADE ONLY. TSA-SA70 OWNER’S MANUAL...
  • Page 22 PCS. Next, re-install the front and rear rails and the main tube (refer to your fence manual). When finished, continue on to the next page. TSA-SA70 OWNER’S MANUAL...

  • Page 23: Assembling The Support Legs

    With the holes aligned, insert a hex head bolt (C) through a washer (d), then through one of the two exposed holes in the leg bracket (G) and support leg (F). Secure the bolt using a 13mm wrench. TSA-SA70 OWNER’S MANUAL...
  • Page 24 Congratulations! You have completed the section to Assemble the Support Legs. Continue to the following page for the next steps for installations WITH the extension wing, or skip to page 21 for the next steps for installations WITHOUT the extension wing. TSA-SA70 OWNER’S MANUAL...

  • Page 25: Attaching The Mounting Bracket

    (E) and the extension wing. Secure the bolt in place with a second washer (f) and a lock nut (g). Only finger tighten the nut at this time. EXTENSION WING UNDER TABLE VIEW TSA-SA70 OWNER’S MANUAL...
  • Page 26 • Congratulations! You have completed the section to Attach the Large Sliding Table Mounting Bracket with the Extension Wing. Continue to page 23 for next steps. TSA-SA70 OWNER’S MANUAL...
  • Page 27 Insert the bolt through the lock washer, through the mounting bracket (E) and into the table. Only finger tighten the bolt at this time. TSA-SA70 OWNER’S MANUAL...
  • Page 28 13mm wrench to tighten the bolts. • Congratulations! You have completed the section to Attach the Large Sliding Table Mounting Bracket without the Extension Wing. Continue to the next page. TSA-SA70 OWNER’S MANUAL...

  • Page 29: Attaching The Positioning Plate

    (E), then thread four socket head cap screws (h) with four washers (i) through the positioning plate (I) and into the exposed mounting holes in the mounting bracket (E). TSA-SA70 OWNER’S MANUAL...
  • Page 30 Tighten the four socket head cap screws (h) with a 6mm hex t-wrench. TSA-SA70 OWNER’S MANUAL...

  • Page 31: Attaching The Inner Guide Tube

    Place the inner guide tube (A) on GUIDE CHANNEL its rear edge (so the bearing guide channel faces up), and align the two round mounting holes in the leg bracket (G) with the two rear threaded holes in the inner guide tube (A). TSA-SA70 OWNER’S MANUAL...
  • Page 32 (I) and inner guide tube (A). Only finger tighten the bolt. Repeat step 4 for the other three exposed holes in the positioning plate (I) and inner guide tube (A). TSA-SA70 OWNER’S MANUAL...
  • Page 33 Mount the front guide bracket (J) to the underside of the front of the inner guide tube (A) using two hex head bolts (j) and two washers (k). Use a 13mm wrench to tighten the bolts. TSA-SA70 OWNER’S MANUAL...
  • Page 34 (l) through three washers (m), then through the three slots and into the holes in the mounting flange. Secure the three bolts by installing three lock nuts (n). Use an 8mm wrench to tighten the bolts. TSA-SA70 OWNER’S MANUAL...

  • Page 35: Installing The Sliding Table Support Assembly

    Installation of the sliding table support assembly is recommended for maximum stability, but it is not required to make your sliding table functional. Note that if you have the SawStop optional Folding Outfeed Table (TSA-FOT), you will not be able to fold the Outfeed Table down if you install the sliding table support assembly.
  • Page 36 Position the mounting bracket only within the area shown: a 6.5” x 4.5” (165mm x 115mm) area under the rear rail in the upper-right corner of the saw cabinet. Ensure the support tube (K) is level before attaching the mounting bracket (1.47). TSA-SA70 OWNER’S MANUAL...
  • Page 37 Use a 13mm wrench to tighten the LOCK NUT two hex head bolts (q) in the support tube (K). Do not tighten the lock nut shown with the gray callout in the figure to the right at this time. TSA-SA70 OWNER’S MANUAL...

  • Page 38: Installing The Lateral Brackets

    (L) underneath the positioning plate (I). Align the square mounting holes in the lateral brackets (L) with the square holes in the positioning plate (I). Repeat step 2 to secure each lateral bracket (L) in place. TSA-SA70 OWNER’S MANUAL...

  • Page 39: Installing The Support Legs

    (H) to the support leg (F). Align the square mounting holes in the cross brace (L) with the square holes in the stepped leg bracket (H), keeping the edge of the bracket generally parallel with the saw table. TSA-SA70 OWNER’S MANUAL...
  • Page 40 (H) and cross brace (L), then through a washer (x) and hex cap nut (w). VIEW FROM UNDER STEPPED LEG MOUNTING BRACKET Repeat step 4 for the other exposed hole. TSA-SA70 OWNER’S MANUAL...
  • Page 41 The last support leg with the leg bracket will be installed after adjustments are made to the guide tubes. Check that the cross braces (L) are still level, then use a 12mm wrench to tighten the hex nuts (b) on both leveling feet (nn). TSA-SA70 OWNER’S MANUAL...

  • Page 42: Installing The Outer Guide Tube

    Repeat step 2 for the other exposed holes in the stepped leg bracket (H) and outer guide tube (B). Move to the other stepped leg bracket and repeat the process. Tighten the bolts using a 13mm wrench. TSA-SA70 OWNER’S MANUAL...

  • Page 43: Installing The Sliding Table & Sliding Table Stops

    (B). Do not worry if the sliding table (M) does not slide smoothly at this point since additional adjustments will likely be needed to ensure smooth movement of the sliding table (M). TSA-SA70 OWNER’S MANUAL...
  • Page 44 Phillips head screwdriver. Repeat this process for the hole on the other end of the outer guide tube (B). The spacers will serve as limit stops to prevent the sliding table (M) from sliding too far forward or backward. TSA-SA70 OWNER’S MANUAL...

  • Page 45: Adjusting The Sliding Table

    (B). VIEW FROM ABOVE TABLE DO NOT OVERLOAD THE BEARINGS. OVERLOADING WILL CAUSE WARPING AND PREVENT THE SLIDING TABLE FROM MOVING SMOOTHLY. TSA-SA70 OWNER’S MANUAL...
  • Page 46 Slide the sliding table (M) towards the rear of the guide tubes. Repeat steps 1-5 for the rear set of bearings with the sliding table (M) near the rear of the outer guide tube (B). TSA-SA70 OWNER’S MANUAL...

  • Page 47: Adjusting The Table Lock Handle

    DO NOT OVER-TIGHTEN THE TABLE LOCK HANDLE AGAINST THE OUTER GUIDE TUBE. Use a 3/4” socket wrench or combination wrench to hold the eccentric nut still, and use a 10mm wrench to tighten the hex head bolt holding the table lock handle. TSA-SA70 OWNER’S MANUAL...

  • Page 48: Adjusting The Spacing

    Push against the outer edge of the sliding table (M) until it presses against the material from step 2. This will also cause the rail and bolts to move relative to the slotted holes in the stepped leg mounting brackets (H). TSA-SA70 OWNER’S MANUAL...
  • Page 49 (B) to the stepped leg brackets (H). Remove the material from step 2. Recheck the spacing between the sliding table (M) and the inner guide tube bearing channel and make any further adjustments as necessary. TSA-SA70 OWNER’S MANUAL...

  • Page 50: Installing The Guide Bearing Assembly

    (B). You may need to push down on the sliding table (M) because the brushes on the bottom of the sliding table (M) may tend to slightly lift the sliding table (M) off the outer guide tube (B). TSA-SA70 OWNER’S MANUAL...
  • Page 51 Use a 10mm wrench or socket wrench to tighten the lock nut on the hex head bolt. TSA-SA70 OWNER’S MANUAL...
  • Page 52 If a lot of pressure is required, or it is not possible to stop the ball bearing from spinning, it is too tight and needs to be loosened. Repeat steps 1-9 for the other guide bearing assembly (N) and mounting hole in the sliding table. TSA-SA70 OWNER’S MANUAL...

  • Page 53: Setting The Bearing Tension

    You may need a flashlight to see the screws. Use a 5mm hex t-wrench to slightly loosen the three screws securing the adjustable bearings, using the access holes in the inner guide tube and guide bearing channel (A). TSA-SA70 OWNER’S MANUAL...
  • Page 54 If the sliding table “jumps” or does not travel smoothly when the front or rear bearings exit or enter the bearing guide channel, adjust the tension on the middle bearing. TSA-SA70 OWNER’S MANUAL...
  • Page 55 (J) and slide the bearing up or down in the slotted hole in the bracket until the bearing contacts the underside of the sliding table (M). TSA-SA70 OWNER’S MANUAL...
  • Page 56 If a lot of pressure is required, or it is not possible to stop the bearing from spinning, it is too tight and needs to be loosened. Use a 10mm wrench to re-tighten the lock nut. TSA-SA70 OWNER’S MANUAL...

  • Page 57: Installing The Angle Guide Rail

    BRACKET T-SLOT Slide the T-slot in the angle guide rail (D) onto the two T-nuts until it is generally centered on the sliding table (M). Only finger tighten the bolts at this time. MITER DETENT POSITIONING BRACKET TSA-SA70 OWNER’S MANUAL...
  • Page 58 Re-check both ends of the guide rail to make sure they are still correct. Then tighten the two bolts. Thread a lock handle (dd) into the smaller, threaded hole in a T-nut (ee). TSA-SA70 OWNER’S MANUAL...
  • Page 59 It may be easier to install the lock handles using a small flat-head screwdriver to thread the screws in the handle assemblies. TSA-SA70 OWNER’S MANUAL...

  • Page 60: Installing The Crosscut Fence Assembly

    Align the T-nut in the fence pivot assembly (O) with the right end of the T-slot on the face with two holes. If necessary, loosen the T-nut to provide clearance for the walls of the crosscut fence. TSA-SA70 OWNER’S MANUAL...
  • Page 61 SOCKET HEAD SCREW Position the miter lock assembly (Q) next to the straight end of the MITER MITER CLAMP crosscut fence (C) (the left end), with DETENT HANDLE the miter detent knob in the KNOB position shown. TSA-SA70 OWNER’S MANUAL...
  • Page 62 Slide the bottom of the fence pivot pin into the fence pivot plate at the FENCE front of the sliding table. Use the PIVOT PIN lock handle in the fence pivot plate to secure the fence pivot assembly (O). FENCE PIVOT PLATE TSA-SA70 OWNER’S MANUAL...
  • Page 63 (C) and the miter lock assembly (Q) until the crosscut fence is perpendicular to the blade, then tighten the miter lock handle and miter clamp handle in the miter lock assembly. Your crosscut fence is now installed in the traditional configuration. TSA-SA70 OWNER’S MANUAL...
  • Page 64 (C) adjacent the crosscut fence ruler and into the hole in the crosscut fence extension, until they contact the crosscut fence extension tube and secure it in place. Do not over- tighten the thumb screws. TSA-SA70 OWNER’S MANUAL...
  • Page 65 Slide the T-nut into the T-slot in the top of the crosscut fence (C). Tighten the lock handle to secure the flip stop (P) in place on the crosscut fence. TSA-SA70 OWNER’S MANUAL...

  • Page 66: Crosscut Fence Assembly Configurations

    (Q). Pivot the left end of the crosscut fence (C) forward until the rounded T-nut slides out of the T-slot in the top of the angle guide rail (D). TSA-SA70 OWNER’S MANUAL...
  • Page 67 Slide the fence pivot assembly (O) out of the right side of the T-slot in the crosscut fence (C). TSA-SA70 OWNER’S MANUAL...
  • Page 68 (M), with the smooth face of the crosscut BEVELED END fence facing towards the front of the saw, and the beveled end of the crosscut fence extending away from the table saw. TSA-SA70 OWNER’S MANUAL...
  • Page 69 T-nut to provide clearance for the walls of the crosscut fence (C). Slide the T-nut about 18” into the T-slot. Do not tighten the miter lock handle or the miter clamp handle at this time. TSA-SA70 OWNER’S MANUAL...
  • Page 70 (C) (and the fence lock assembly (Q)) until the crosscut fence is perpendicular to the blade, then tighten the miter lock handle and lock handle in the fence lock assembly. Your crosscut fence is now installed in the Euro configuration. TSA-SA70 OWNER’S MANUAL...

  • Page 71: Storage

    In order to store your crosscut fence assembly, follow steps 1-3 and step 5 of the Euro Configuration instructions to remove the crosscut fence assembly from the sliding table, and set it in the crosscut fence storage brackets attached to the support legs shown below. TSA-SA70 OWNER’S MANUAL...

  • Page 72: Installing The Logo Plate

    (S), then through each of the holes in the stepped leg mounting bracket (H), followed by a washer (hh) and a hex cap nut (ii). Tighten the nuts using a 13mm wrench. TSA-SA70 OWNER’S MANUAL...

  • Page 73: Adjustments

    Lay a straight edge across the front of the sliding table top so that it extends over the top of the table saw near the front of the mounting bracket. TSA-SA70 OWNER’S MANUAL...
  • Page 74 Repeat step 2, but lay the straight edge across the sliding table top near the rear of the mounting bracket. TSA-SA70 OWNER’S MANUAL...
  • Page 75 Use a 13mm wrench to tighten the four hex head bolts attaching the mounting bracket to the extension wing or saw table. For PCS with extension wing: Use 13mm wrenches to tighten the M8 bolts and M8 nuts. TSA-SA70 OWNER’S MANUAL...

  • Page 76: Installing The Remaining Support Leg

    Thread the leveling foot all the way into the support leg. Attach the leg bracket to the outer guide tube using two hex head bolts (jj) and two washers (kk). Use a 13mm wrench to tighten the bolts. TSA-SA70 OWNER’S MANUAL...
  • Page 77 Make sure not to unthread the leveling foot too much, as this will raise the rear of the sliding table so that it is no longer parallel to the saw table. TSA-SA70 OWNER’S MANUAL...

  • Page 78: Aligning To The Blade

    Raise the saw blade to the highest elevation. Place a straightedge or rip fence flush against the left side of the blade. If using a rip fence, adjust it if necessary to be parallel to the blade. Consult your fence manual for details. TSA-SA70 OWNER’S MANUAL...
  • Page 79 TSA-SA70 OWNER’S MANUAL...
  • Page 80 Move the rear end of the outer guide tube slightly towards the blade. TSA-SA70 OWNER’S MANUAL...
  • Page 81 It will be aligned later, so do not re-tighten the hex head bolt to secure it in place at this time. TSA-SA70 OWNER’S MANUAL...
  • Page 82 Now tighten the lock nut on the LOCK NUT support tube (K) shown in the gray callout in the figure on the right. TSA-SA70 OWNER’S MANUAL...

  • Page 83: Setting The Miter Angle Ruler Traditional

    Do not tighten the lock handles on the miter lock assembly or the fence lock assembly. Use a machinist or engineering square to position the crosscut fence exactly 90 degrees relative to the saw blade. TSA-SA70 OWNER’S MANUAL...
  • Page 84 6. Re-tighten the hex head bolts to lock the guide rail in place. Tighten the lock handles on the miter lock assembly and the fence lock assembly to lock the crosscut fence in place. TSA-SA70 OWNER’S MANUAL...
  • Page 85 When aligning the fence with the desired marking on the miter angle ruler, read markings on the side of the fence that faces away from the operator. TSA-SA70 OWNER’S MANUAL...

  • Page 86: Setting The Miter Angle Ruler (Euro)

    Use a machinist or engineering square to position the crosscut fence exactly 90 degrees relative to the saw blade. Tighten the lock handles on the miter lock assembly and the fence lock assembly to lock the crosscut fence in place. TSA-SA70 OWNER’S MANUAL...
  • Page 87 10mm wrench to loosen the hex head bolt at the rear end of the guide rail and adjust the miter detent pin positioning locator block until it aligns with the miter detent pin. Re-tighten the hex head bolt. TSA-SA70 OWNER’S MANUAL...

  • Page 88: Setting The Crosscut Fence Ruler

    Make sure the table saw motor is off and the blade is completely stopped. Install the crosscut fence in the traditional configuration (at the front of the sliding table). Adjust the flip stop assembly to about 12” from the blade. TSA-SA70 OWNER’S MANUAL...
  • Page 89 Push the Start/Stop paddle in to stop the blade and power OFF the saw. Use a tape measure to check the dimension of the cut piece of wood. TSA-SA70 OWNER’S MANUAL...
  • Page 90 TO REDUCE THE POTENTIAL FOR KICKBACK AND A SERIOUS INJURY, MOVE THE RIP FENCE OUT OF CONTACT WITH THE WORKPIECE WHEN CROSS-CUTTING TO PREVENT THE WORKPIECE FROM BINDING BETWEEN THE RIP FENCE AND THE BLADE. TSA-SA70 OWNER’S MANUAL...

  • Page 91: Operations

    To prevent the sliding table from moving, push the table lock handle toward the back of the sliding table. When the sliding table is not in use, lock it in place so that it will not move unexpectedly. TSA-SA70 OWNER’S MANUAL...
  • Page 92 The sliding crosscut table assembly can then be lifted up and moved to the desired location. TSA-SA70 OWNER’S MANUAL...

  • Page 93: Reference

    Large Sliding Table system is modified without the prior written permission of SawStop, LLC, or if the Large Sliding Table system is located or has been used outside of the country where the authorized SawStop distributor from whom the Large Sliding Table system was purchased resides.

  • Page 94: Safety

    Everyday eyeglasses are not safety glasses. 6. Keep hands out of the line of the saw blade. Never reach around or over the saw blade. Keep proper footing and balance at all times. TSA-SA70 OWNER’S MANUAL...
  • Page 95 Any parts that are damaged should be properly repaired or replaced. TSA-SA70 OWNER’S MANUAL...

  • Page 96: Support System Exploded View

    Support System Exploded View TSA-SA70 OWNER’S MANUAL...

  • Page 97: Support System Parts List

    M6 x 1.0 Lock Nut TSA-SA70-032 1.33 Positioning Plate TSA-SA70-033 1.10 M8 x 19 x 2 Washer TSA-SA70-034 1.11 M8 x 1.25 x 16 Hex Head Bolt TSA-SA70-035 1.36 M8 x 1.25 x 12 Socket Head Cap Screw TSA-SA70-036 TSA-SA70 OWNER’S MANUAL...
  • Page 98 M5 x 1.25 x 18 Pan Head Phillips Self-Tapping Screw TSA-SA70-048 1.49 Sliding Table Support Sleeve TSA-SA70-049 1.50 Frame Support Mounting Bracket TSA-SA70-050 1.39 M8 x 1.25 Lock Nut TSA-SA70-051 1.52 M8 x 1.25 x 16 Carriage Head Shoulder 2.3mm Bolt TSA-SA70-052 1.53 Support Tube TSA-SA70-053 TSA-SA70 OWNER’S MANUAL...
  • Page 99 This page is intentionally blank. TSA-SA70 OWNER’S MANUAL...
  • Page 100 Table Assembly Exploded View TSA-SA70 OWNER’S MANUAL...
  • Page 101 6mm Hex T-Wrench TSA-SA70-085 2.31 5mm Hex T-Wrench TSA-SA70-086 2.32 Table Lock Handle TSA-SA70-087 2.33 M10 x 14.5 Wave Washer TSA-SA70-088 2.34 M6 x 13 x 1 Washer TSA-SA70-089 2.35 Guide Bearing Bracket TSA-SA70-090 2.36 Guide Bearing Assembly TSA-SA70-091 TSA-SA70 OWNER’S MANUAL...

  • Page 102: Crosscut Fence Exploded View

    Crosscut Fence Exploded View TSA-SA70 OWNER’S MANUAL...

  • Page 103: Crosscut Fence Parts List

    19.2 x 28 x 1.5 Plastic Washer (Adhesive Backed) TSA-SA70-123 2.10 M6 x 1.0 x 3.5 T-Nut TSA-SA70-124 3.23 Spring Pin (6mm x 20mm) TSA-SA70-125 3.35 Crosscut Fence Miter Lock Glide Pad TSA-SA70-126 3.36 Adhesive Miter Plate Glide Pad Tape TSA-SA70-127 TSA-SA70 OWNER’S MANUAL...
  • Page 104 Miter Detent Knob TSA-SA70-135 3.45 M6 x 1.0 Miter Lock Handle TSA-SA70-136 3.46 Miter Lock Pivot Sleeve TSA-SA70-137 3.47 19.2 x 28 x 1.5 Plastic Washer TSA-SA70-138 3.48 15mm O-Ring TSA-SA70-139 3.49 Miter Detent Pin Block TSA-SA70-140 TSA-SA70 OWNER’S MANUAL...
  • Page 105 This page is intentionally blank. TSA-SA70 OWNER’S MANUAL...
  • Page 106 This page is intentionally blank. TSA-SA70 OWNER’S MANUAL...
  • Page 107 This page is intentionally blank. TSA-SA70 OWNER’S MANUAL...
  • Page 108 SawStop, LLC 11555 SW Myslony St | Tualatin, Oregon 97062 USA www.sawstop.com Main Phone: (503) 570-3200 Service: (503) 582-9934 Fax: (503) 570-3303 Email: info@sawstop.com August 2018 M TBL 19 0001 00...

Table of Contents