Table of Contents
Advertisement
correct it. It is also a good idea to carry a few spare
parts that will correct a small problem that may
develop. These parts can be obtained from your
dealer or larger campground stores. Refer to the
toilet manufacturer's information in your Owner's
packet to determine which part you may need, its
correct name and part number. (If you have a
different toilet than the one described, follow the
manufacturer's recommendations for cleaning and
maintenance.)
Dumping the Holding Tanks
The holding tanks terminate in a valve arrangement
that permits each tank to be dumped separately or
together. The valves are called "knife valves". A
blade closes the opening in the sewer drain pipes.
The blade is connected to an extension handle that
is pulled to release the contents of the tanks(s).
During self-containment use, the sewer outlet line
should be securely capped, and valves closed to
prevent leakage of waste material on the ground or
pavement.
Holding tanks are enclosed sewer systems and as
such must be drained into an approved dump
station. Both black and gray water holding tanks
must be drained and thoroughly rinsed to prevent
accumulation of harmful or toxic materials.
Dump the holding tanks only when they are about
2/3 full. If necessary, fill the tanks with water to 2/3
full. This provides sufficient water to ensure
complete flushing of waste material into the sewer
line. Whenever possible, dump the holding tanks
before traveling.
The holding tanks outlet is set up to be used with a
removable fitting that locks onto the outlet with
clockwise twist. The sewer drain hose is clamped
on this fitting when you need to drain the holding
tanks. When you are operating self-contained, or
you store the camper, install the protective cap in
place of the removable hose.
The sewer (dump) hose is compressed and stored in
the camper's hose carrier.
Draining the holding tanks:
1) Attach the sewer hose to the dump outlet.
2) Extend the hose and insert the hose end into
the sewer or dump station inlet, pushing it
firmly into the opening to be secure. In some
cases, adapters may be necessary between
the hose and inlet.
3) Arrange the sewer hose so it slopes evenly
and is supported to maintain the slope.
4) Dump the black water holding tank first.
Grasp the handle of the black water knife
valve firmly and slide the valve open with a
steady pull.
5) Allow enough time for the tank to drain
completely. Rinse and flush the tank and
drain hose through the toilet with a bucket of
water or a hose.
6) When the tank flow stops, push the handle
in to close the valve.
7) Pull the handle for the grey water holding
tank. Repeat steps 4 through 6. This tank is
dumped last to aid in flushing the outlet and
drain hose.
8) Remove the sewer hose and replace the
outlet cap.
9) Rinse out the sewer hose with fresh water
and remove the sewer hose from the dump
station.
10) Replace sewer or dump station cover(s).
11) Store the sewer hose.
NOTE: Follow these guidelines to ensure trouble-
free operation:
Never put anything in the black tank other
than biodegradable RV toilet paper.
Do not put automotive antifreeze, household
toilet cleaner or drain cleaners, or any solid
materials into the waste water system.
Always use chemicals in the black water
system that are made especially for this
purpose.
When cleaning components of the waste
water system, use cleaners made for camper
systems.
Always keep the drain cap in place and
termination valves closed.
After every third time the holding tanks are
emptied, fill and flush both tanks with clean,
fresh water a few times to keep them clear
and clean.
NOTE: To facilitate draining, the camper should be
slightly lower in the front to allow drainage toward
drains located on the driver's side front.
If you are parked at a site with a sewer hookup,
keep the black water knife valve closed to allow the
waste level to build up. The outlet will probably
clog if you leave the knife valve open continually.
31
Hide quick links:
Advertisement
Table of Contents
