If you have any question or problem concerning your receiver, please consult your nearest Sony dealer. About This Manual The instructions in this manual are for model RM-PP404. Check your model number by looking at the lower right corner of the front side.
Before You Use Your Remote Check that you received the following item with the remote: R6 (size-AA) batteries (2) Inserting batteries into the remote Insert two R6 (size-AA) batteries with the + and – properly oriented in the battery compartment. When using the remote, point it at the remote sensor receiver.
Location of Parts and Basic Remote Operations This chapter provides information on the location of buttons and how to use them to perform basic operations. However, some functions explained in this section may not work depending on the model of the receiver. For the functions of the receiver you purchased, refer to the Operating Instructions supplied with the...
If you are using a TV, you can use this remote to operate the TV without turning on the receiver. When you are using a Sony TV, pressing this button turns on the TV and switches to TV input. 6 MASTER VOLUME +/– buttons Press to adjust the volume level of all speakers at the same time.
SWAP button Press to swap the small and large pictures POSITION button Press to change the position of the small picture JUMP button Press to toggle between the previous and the current channels. Only with Sony TVs with the picture-in-picture function.
MENU MENU EXECUTE ENTER CURSOR MENU MODE GUIDE EXIT/RETURN TITLE TEST TV/VIDEO WIDE EQ/TONE TONE LEVEL P IN P SWAP REAR CENTER POSITION JUMP – – Lift up the top cover. qh VCR MENU button Press to display the VCR menu on the TV screen. Then use the cursor buttons on the remote to perform the menu operations (see “qj Cursor buttons (V/v/ B/b), EXECUTE/ENTER button, and EXIT/RETURN...
Parts Description ? / 1 ? / 1 SLEEP SYSTEM STANDBY SHIFT ENTER > 10 - / - - D.TUNING – MUTING – SUB CH > DISC D.SKIP TV/VTR RETURN VIDEO1 VIDEO2 VIDEO3 DVD/LD TV/SAT MD/TAPE TV CONTROL TUNER PHONO 5.1CH SOUND FIELD A.F.D.
IR SET button Use this button to program the remote with the signals to control non-Sony components (see page 13). * The function of these buttons switch automatically each time you press the function buttons (4). The above explanation is intended to serve as an example only.
Parts Description Table of buttons that you can use to control each component Component DAT deck player Button(s) AV ?/1 Numeric buttons SHIFT >10 -/-- ENTER D.TUNING VOL – VOL + MUTING ./> SUB CH +/– DISC D.SKIP ANT TV/VTR RETURN z + N z + n...
Advanced Remote Operations This chapter describes how to change the factory setting of a function button and how to set the remote to control non-Sony components. ? / 1 ? / 1 SLEEP Program SYSTEM STANDBY indicator SHIFT ENTER >...
Function buttons: Come with factory settings that can be changed to suit the components you have. IR SET: Press to set the remote to operate non-Sony components. Operating Other Components You can program the remote to control other components by changing the code or non-Sony components.
Use the numeric codes in the tables below to control non- Sony conponents and also Sony components that the remote is normally unable to control. Since the remote signal that a component accepts differs depending on the model and year of the component, more than one numeric code may be assigned to a component.
Operating Other Components To control a CD player Maker Code(s) SONY 101, 102 DENON 103, 104 105, 106, 107 KENWOOD 108, 109, 110 MAGNAVOX 111, 116 MARANTZ ONKYO 112, 113, 114 PANASONIC PHILIPS PIONEER TECHNICS 115, 118, 119 YAMAHA 120, 121, 122...
To control a VCR Maker Code(s) SONY 701, 702, 703, 704, 705, 706 AIWA 710, 750, 757, 758 AKAI 707, 708, 709, 759 BLAUPUNKT EMERSON 711, 712, 713, 714, 715, 716, 750 FISHER 717, 718, 719, 720 GENERAL ELECTRIC 721, 722, 730...
If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. The remote does not function. , Point the remote at the remote sensor receiver.
Specifications General Remote control system Infrared control Power requirements 3 V DC with two R6 (size-AA) batteries Dimensions 56 25 mm Mass (approx.) 130 g excluding batteries Design and specifications are subject to change without notice.