Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Magnocomp magDomus MGD2 Series
- Page 1 . User Guide...
- Page 2 Version, 1.31, Feb.2012 www.magnocomp.com This User Guide applies to the complete family line of magDomus from magnocomp, including the models: ● MGD2xxx ● MGD300x ● MGD301x...
- Page 3 At a Glance The magnocomp’s magDomus is a light and high flexible equipment that takes care and automates your home. The magDomus Home Controller checks and monitors status of all your electric devices and automatically controls every element according to your life style. If necessary, it even informs you of what is happening in your home.
- Page 4 Fig. 1. Front view Fig. 2. Rear view The magDomus can interact with any remote configuration station in the Internet, using its standard Ethernet port. The magDomus can monitor and control any Home Automation network through specific adaptor devices.
- Page 5 Fig. 3. magDomus ecosystem...
- Page 6 Verify that the transformer is compatible in form factor and in electrical specification to the available power mains standardized in your country. In case of incompatibility please contact your local magnocomp supplier for a solution. Fig. 4. Power supply transformer (example) 2.
- Page 7 network equipment, like a router or a switch. The connection to a network is recommended but not strictly required in order to configure and to operate your equipment. Your device can be configured and operated through a locally attached computer keyboard. The connection to the Internet is not required to the basic operation of your equipment.
- Page 8 Configure The magnocomp’s magDomus can be configured locally, with a directly attached keyboard or through the friendlier provided Web interface. Accessing the configuration Web interface When connected to a network, the brand new magDomus device will try to obtain a valid IP address from the network using DHCP (Dynamic Host Configuration Protocol).
- Page 9 Device collector The magnocomp’s device collector can help you finding your device in cases when you don't know its IP address due to: ● You are using a local network where addresses are assign dynamically by a DHCP server (case 1), and/or ●...
-
Page 10: Client Setup
● Scheduler ● Reboot device ● User Manual ● magnocomp Web Portal Network Setup To configure the network connection select the option “Network” in the configuration application. The following network parameters can be defined: DHCP Use the Dynamic Host Configuration Protocol (DHCP). -
Page 11: Access Control
A local network should not include two magDomus devices with the same name. This name must start with a letter and the other characters can include letters or numeric characters. Spaces are not allowed. IP address The device IP (IPv4) address. This is not required when using DHCP. NetMask The network mask. -
Page 12: Date And Time
After adjusting the parameters according to requirements, press the Save button to store the security parameters or the Discard button to leave parameters unchanged.. Date and Time Each magDomus device maintains a internal clock. This clock keeps running even when the device is switched off or unplugged from the main power. -
Page 13: Home Automation
Home Automation Fig. 8. The Home Automation setup window After adjusting the parameters according to requirements, press the Save button to store the network parameters or the Cancel button to leave parameters unchanged.. Scheduler You can adjust the scheduler setting using the the option “Scheduler” in the magDomus Setup page. Fig. - Page 14 Minute The minute when the event will be triggered. You can specify : ● a integer number (00-59) ● a set of comma separated integer numbers ● a ‘*’ character to indicate every minute. Hour The hour when the event will be triggered. You can specify : ●...
- Page 15 Cloud Your magDomus can be operated directly, or through the magDomus Control Panel hosted over the magnocomp’s Internet cloud infra-structure (ControlCloud). Please refer to the section Client Setup to select the desired configuration for your magDomus Client. The magDomus Control Cloud can be accessed by following the URL: http://www.magnocomp.com/magdomus...
-
Page 16: Control Panel
Control Panel The picture presents the screen layout for the magDomus control panel. In the left panel you can select a home automation unit to display and control. The right panel presents the state of the selected unit (when available) and allows its interactive control. Fig. - Page 17 automation networks do not implement state queries. Z The Z field is usually used to store the unit height coordinate or the floor where the unit is located.
- Page 18 Specs Platform EB6010 Software magnocomp 3.x Operating System magBoxLinux Configuration USB flashdisk download, FTP, Embbeded Web Server Internal Clock Autonomous. Sincronization using NTP (requires network connection) Security Password protected for both user and admin. Remote workstation control.
-
Page 19: Legal Information
Legal Information This user guide is published by magnocomp or its local affiliated company, without any warranty. Improvements and changes to this user guide necessitated by typographical errors, inaccuracies of current information, or improvements to programs and/or equipment, may be made by magnocomp at any time and without notice. - Page 20 Under no circumstances will magnocomp be liable in any way for your improper use of additional content or other third party content.
-
Page 21: Equipment Disposal
To comply with the european directive on WEEE (Waste Electrical and Electronic Equipment), electronic used devices from private households in EU can be returned free of charge. For details please contact your local distributor or inquire magnocomp directly.