Table of Contents
Advertisement
Rotary Sieve 360 + Hopper
Customer Product Manual
Part 7580607_01
Issued 10/18
For parts and technical support, call the Industrial Coating
Systems Customer Support Center at (800) 433-9319 or
contact your local Nordson representative.
This document is subject to change without notice.
Check http://emanuals.nordson.com for the latest version.
NORDSON Deutschland GmbH
Advertisement
Table of Contents
Summary of Contents for Nordson AZO E360
- Page 1 Issued 10/18 For parts and technical support, call the Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative. This document is subject to change without notice. Check http://emanuals.nordson.com for the latest version. NORDSON Deutschland GmbH...
- Page 2 Contact Us Notice This is a Nordson Corporation publication which is protected by copyright. Nordson Corporation welcomes requests for information, comments, and Original copyright date XXXX. No part of this document may be inquiries about its products. General information about Nordson can be...
- Page 3 Change Record Change Record Revision Date Change Part 7580607_01 E 2018 Nordson Corporation...
- Page 4 Change Record Part 7580607_01 E 2018 Nordson Corporation...
-
Page 5: Table Of Contents
..........Part 7580607_01 E 2018 Nordson Corporation... -
Page 6: Safety
Regulations and Approvals Make sure all equipment is rated and approved for the environment in which it is used. Any approvals obtained for Nordson equipment will be voided if instructions for installation, operation, and service are not followed. All phases of equipment installation must comply with all federal, state, and local codes. -
Page 7: Personal Safety
Clean, maintain, test, and repair equipment according to the instructions in your equipment documentation. Use only replacement parts that are designed for use with original equipment. Contact your Nordson representative for parts information and advice. Part 7580607_01 E 2018 Nordson Corporation... -
Page 8: Transport
Unpacking Upon receipt, unpack the Rotary Sieve & Hopper carefully to avoid damage. Report any damage immediately to the shipper and to your Nordson representative. Save packing materials for possible later use, or dispose of properly according to local regulations. -
Page 9: Installation
Provide adequate fuse/circuit protection from the power supply. Refer to the foldout wiring diagrams and schematics at the end of this manual for more information. Initial start- up should be performed only by a Nordson field engineer or technician. Pneumatic Connections For the connection size, location and volume required please refer to your Service Requirements drawing or contact your Nordson representative. -
Page 10: Grounding
If a system or any equipment in a system malfunctions, shut off the system immediately and perform the following steps: Disconnect and lock out electrical power. Close pneumatic shutoff valves and relieve pressures. Identify the reason for the malfunction and correct it before restarting the equipment. Part 7580607_01 E 2018 Nordson Corporation... -
Page 11: Description - Full Assembly
Figure 1 360 Rotary Sieve + Hopper assembly The Rotary Sieve + Hopper assembly is available in 6 variations. 3 for the 360 and 3 for the 650 (Ask Nordson for Appendix A for the 650) Option Part Number Description... -
Page 12: Using The Illustrated Parts List
A dash (—) is used when the part number applies to all parts in the illustration. The number in the Part column is the Nordson Corporation part number. A series of dashes in this column (- - - - - - ) means the part cannot be ordered separately. -
Page 13: Configuration 1 - Rotary Sieve 360 - Hdlv
Note: Care must be taken to ensure there is no sag in the venting hoses as this could allow powder to collect inside and block the venting flow. Pay attention to the location of the vents (8). Part 7580607_01 E 2018 Nordson Corporation... -
Page 14: Dimensions - Configuration 1
Dimensions - Configuration 1 1581 1335 Figure 3 360 Assembled Dimensions - Configuration 1 Part 7580607_01 E 2018 Nordson Corporation... -
Page 15: Configuration 2 - Rotary Sieve 360 - Venturi
Note: Care must be taken to ensure there is no sag in the venting hoses as this could allow powder to collect inside and block the venting flow. Pay attention to the location of the vents (5). Part 7580607_01 E 2018 Nordson Corporation... -
Page 16: Dimensions - Configuration 2
Dimensions - Configuration 2 1519 1335 Figure 5 360 Assembled Dimensions - Configuration 2 Part 7580607_01 E 2018 Nordson Corporation... -
Page 17: Configuration 3 - Rotary Sieve 360 - Venturi, Pe
Note: Care must be taken to ensure there is no sag in the venting hoses as this could allow powder to collect inside and block the venting flow. Pay attention to the location of the vents (2 & 7). Part 7580607_01 E 2018 Nordson Corporation... -
Page 18: Dimensions - Configuration 3
Dimensions - Configuration 3 1519 1335 Figure 7 360 Assembled Dimensions - Configuration 3 Part 7580607_01 E 2018 Nordson Corporation... -
Page 19: Parts - Hdlv - 150L Powder Feed Hopper
Hopper The HDLV- 150L Powder Feed Hopper is used to hold the virgin and reclaimed powder when using Nordson HDLV powder feed pumps. It comes fitted with casters and removable lid for easy operator access. Fitted with level sensors, it automatically monitors the powder level and maintains the required level of powder. -
Page 20: Parts - Venturi - 150L Powder Feed Hopper
Hopper The Venturi - 150L Powder Feed Hopper is used to hold the virgin and reclaimed powder when using Nordson Encore powder feed pumps. It comes fitted with casters and removable lid for easy operator access. Fitted with level sensors, it automatically monitors the powder level and maintains the required level of powder. -
Page 21: Mini Cyclone
Mini cyclone lid Push in fitting 8 mm Blind Plug 1/2” Hose Tail 1/2” 13mm Dimensions Height (including top vent) 532 mm Length (over inlet tubes) 250 mm Depth (excluding top vent) 160 mm Part 7580607_01 E 2018 Nordson Corporation... -
Page 22: Magnetic Separator
GRATE,TRAMP IRON,4 TUBE,8.5 X6 NOTE: Magnets are ordered separately. One set of each item, 1 & 2, are required for each assembly. Dimensions Height 211 mm Length 225 mm Depth 174 mm (+ 41 mm for handle) Part 7580607_01 E 2018 Nordson Corporation... -
Page 23: Accumulator
Cover, Separator, 16 Inlet, St.St. Fitting, Pneumatic, Elbow - SMC 7033473 BRACKET,SUPPORT,TRANSFER HOSE Fitting, G1/2 - 13 mm I/D Hose Vent, Accumulator Cap, PVC, Inlet Note: 4 off are supplied with a standard delivery. Part 7580607_01 E 2018 Nordson Corporation... -
Page 24: Operation
If the lip seals are undamaged, but powder has contaminated the bearings, increase the purge air pressure. Air quality must be according to ISO 8573.1 Class 1:4:2 Incoming air pressure must not exceed 7 bar ,maximum. Part 7580607_01 E 2018 Nordson Corporation... -
Page 25: Maintenance
Refer to your system component manuals for maintenance procedures for all other system equipment. For all maintenance requirements of the rotary sieve, please refer to the AZO E360B technical manual; this can be supplied by Nordson upon request. Daily Maintenance Note: You may need to perform these procedures more or less often, depending on your application requirements. -
Page 26: Periodic Maintenance
Refer to Grounding in the Safety section of this manual and to publication number TCTT- 06- 3881 on the Nordson emanuals website (http://emanuals.nordson.com/finishing) for more information on powder coating system grounding. -
Page 27: Troubleshooting
Powder backing up in Clean the powder path Restriction in sieve and/or powder the accumulator path causing blockage Adjust the vent-assist air pressure Vent- assist air pressure too high Repair Contact your Nordson representative for repair information. Part 7580607_01 E 2018 Nordson Corporation... -
Page 28: Parts
Parts To order parts, call the Nordson Industrial Coating Systems Customer Support Center at (800) 433-9319 or contact your local Nordson representative. Part Description Note 7033452 SCREEN 0,850MM,NYLON,ROTARY SIEVE E360B 7033453 SCREEN 0,400MM,NYLON,ROTARY SIEVE E360B 7033454 SCREEN 0,250MM,NYLON,ROTARY SIEVE E360B... -
Page 29: Specifications - Rotary Sieve 360 Assembly
Voltage (V) Power (kW) 0.75 Frequency (Hz) Protection IP54 Noise Less than 80dB (A) measured at a distance of 1 m from the surface of the unit and at a height of 1.6 m. Part 7580607_01 E 2018 Nordson Corporation... -
Page 30: Diagrams
Diagrams Description Part Number Control Box - Sieve E360 & E650 47.20- 00.00 A Pneumatic - Sieve E360 & E650 47.20- 00.00 B Part 7580607_01 E 2018 Nordson Corporation... - Page 31 Part 7580607_01 E 2018 Nordson Corporation...
- Page 32 Part 7580607_01 E 2018 Nordson Corporation...