Selection Of Digital Input Function - JPS PDA Series Instruction Manual

8. Selection of Digital input function

The terminals DI1, DI2, DI3, & DI4 are multi-functioned Digital Input terminals.
【Note】All the DIx terminals are scanned once every 5.0 ms.
These four terminals are exactly identical in its hardware/software configurations.
When left open, they are OFF. And will become ON when connected to DCOM.
Each input terminal can be configured individually by corresponding DIx_SELECT parameters.
The four DIx_SELECT parameters are:
Pr.41 -- DI1_SELECT, used for DI1
Pr.42 -- DI2_SELECT, used for DI2
Pr.43 -- DI3_SELECT, used for DI3
Pr.44 -- DI4_SELECT, used for DI4
Pr.03 -- DI5_SELECT, used for DI5 (Sec. 1.2 RUN mark terminal)
Pr.04 -- DI6_SELECT, used for DI6 (Sec. 1.2 REV mark terminal)
Selection Table of Digital input function
Pr.41,42,43,44 FUNCTION
0 NULL
1 EMS
2 SPD3
3 SPD2
4 SPD1
5 JOG
6 OH
7 TMIA
8 ON_BB
9 FJR
10 RJR
11 TMIB
12~14 Reserve
15 U/D COUNTER CLEAR
16 U/D COUNTER LOAD
17 U/D COUNTER HOLD
18 OFF_BB
19 U/D COUNTER UP
20 U/D COUNTER DOWN
21 ALARM CLEAR
22 SET1 (FF1)
23 CLR1 (FF1)
24 SET2 (FF2)
25 CLR2 (FF2)
26 SET (FF1&FF2)
27 CLR (FF1&FF2)
28 CLK Input
29 Reserve
30 /OH
31 Normal/Auto SW
32~35 Reserve
36 TMIC
37~47 Reserve
48 Speed Hold
49 Reserve
50 PID Enable
51 PID Hold
52 PID Clear
53 PID Preset
54 PID Bias Enable
55 PID Boost Enable
56-68 Reserve
69 DC-BRAKE1
70 DC-BRAKE2
71 DC-BRAKE3
72 Sensor-Less Mode Change
73 RUN function
74 REV function
75 POWER-CONTROL select
76 FORWARD INHIBIT
COMMENT
NO FUNCTION
EMERGENCY STOP
SPEED SET
SPEED SET
SPEED SET
JOG SPEED SET
OVER HEAT ERROR,
TIMER INPUT for TYPE A
BASE BLOCK if DIx is ON
FORWARD JOG RUN
REVERSE JOG RUN
TIMER INPUT for TYPE B
SET UP/DOWN COUNTER to Pr.16
SET UP/DOWN COUNTER to Pr.15
HOLD "Output HZ" to UP/DOWN COUNTER
BASE BLOCK if DIx is OFF
INCREASE UP/DOWN COUNTER
DECREASE UP/DOWN COUNTER
CLEAR ALARM WHEN ALARM OCCUR
SET input of Flip/Flop-1
CLEAR input of Flip/Flop-1
SET input of Flip/Flop-2
CLEAR input of Flip/Flop-2
SET input to both FF1 & FF2
CLEAR input to both FF1& FF2
Input CLOCK to Timer/Counter Block
OVER HEAT ERROR, (input open)
Change Over Switch for Normal or Auto Run
TIMER INPUT for TYPE C
Hold Output Speed
PID Enable
PID Integrator Hold
PID Integrator Clear
Preset PID Integrator
PID Bias Enable
PID Boost Enable
DC injection brake use AI1 as brake level
DC injection brake use AI2 as brake level
DC injection brake use AI3 as brake level
Select or non-select the SENSOR-LESS mode
Select standard RUN function, Refer to Sec.6
Select standard REV function, Refer to Sec.6
Select AI2 or AI3 for Power Control input
Forward run inhibit
32