Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Marmitek X10 SS12E
Summary of Contents for Marmitek X10 SS12E
- Page 1 SS12E SS12E ™ USER MANUAL ™ 20472/20120530 • SS12E ALL RIGHTS RESERVED MARMITEK ©...
-
Page 2: Table Of Contents
TABLE OF CONTENTS TABLE OF CONTENTS............2 SAFETY WARNINGS ............3 HOW DOES MARMITEK X10 WORK? ......4 ADRESSES ................. 4 SIGNAL RANGE ..............5 INSTRUCTIONS FOR USE SS12™ WIRELESS SWITCH ..7 INTRODUCTION ............... 7 PROPERTIES..............7 CHANGE OF THE HOUSECODE........7 CHANGE OF THE UNITCODE ........... -
Page 3: Safety Warnings
In case of improper usage or if you have altered and repaired the product yourself, all guarantees expire. Marmitek does not accept responsibility in the case of improper usage of the product or when the product is used for purposes other than specified. Marmitek... -
Page 4: How Does Marmitek X10 Work
HOW DOES MARMITEK X10 WORK? Marmitek X10 components use the existing mains wiring to communicate (using Marmitek X10 signals). You can build a complete system using the three different kind of components of the Marmitek X10 System: 1. Modules: These components will receive Marmitek X10 signals and will switch or dim the attached lamp or appliance. -
Page 5: Signal Range
FD10’s. 2. It is possible that Marmitek X10 signals are attenuated by devices and lights which are connected to the power line. In a normal home situation this effect is negligible (the Marmitek X10 system is using active gain control to eliminate the effects). - Page 6 TALK mode (continuous transmission). When these kind of signals are present on the power line it is possible that the Marmitek X10 signals will not come through. 5. The mains do not stop at the front door of your home.
-
Page 7: Instructions For Use Ss12™ Wireless Switch
The SS12 wireless switch transmits radio graphical signals to an X10 Transceiver TM13, IRRF7243 or Marmitek X10 Alarm station. Then the Transceiver or Station transmits these signals via the in your house already installed electric wiring. Through this you can switch on and off your lighting (or apparatus) connected to X10 receivers (lighting can be dimmed also). -
Page 8: Change Of The Unitcode
Use an identical 12V Alkaline battery (type A23). Mind the polarity when replacing. APPLICATIONS With the Marmitek X10 SS12 wireless switch you can activate pre-programmed macros in the CM15Pro computer interface. You can also use the SS12 as a central operation panel for your Marmitek installation. -
Page 9: Freqently Asked Questions
What is the reason for modules to switch on/off spontaneously? It is possible that a Marmitek X10 System is installed at one of your neighbours using the same HouseCode. To solve this problem try to change the HouseCode of your system, or have FD10 Phase Coupler/Filter installed at your incoming mains. -
Page 10: Technical Data
For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product. © MARMITEK... -
Page 11: Declaration Of Conformity
DECLARATION OF CONFORMITY Hereby, Marmitek BV, declares that this SS12 is in compliance with the essential requirements and other relevant provisions of the following Directives: Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and... -
Page 12: Copyrights
COPYRIGHTS Marmitek is a trademark of Pattitude B.V. SS12™ is a trademark of Marmitek B.V. All rights reserved. Every effort has been made to ensure that the information in this manual is accurate. Marmitek is not responsible for printing or clerical errors. - Page 13 SS12...
- Page 14 © MARMITEK...
- Page 15 SS12...