4.1 Device Information LLN0 ........12 Specifications are subject to change without notice. 4.1.1 Report Control Blocks ......12 Littelfuse Startco is not liable for contingent or consequential 4.1.2 Default Datasets ........13 damages, or for expenses sustained as a result of incorrect 4.1.3 GOOSE Control Blocks ......
Page 4
Page iii SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 This page intentionally left blank.
Page 1 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 1. G ENERAL TABLE 1. D IP S EFAULT ETTINGS This manual describes the features of the SE-330, NTERFACE SE-330AU, and SE-330HV IEC 61850 interface. Unless IP Address 192.168.1.100 otherwise indicated, “SE-330”...
Page 3 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 FIGURE 3. Top View of SE-330 (SE-330-X7-XX) with Single Fiber SC and Single RJ-45 Ethernet Network Communications. FIGURE 4. Top View of SE-330 (SE-330-X8-XX) with Dual Fiber SC Ethernet Network Communications.
Page 4 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 modified and written to the SE-330 by clicking “Write to 3. IEC 61850 C ONFIGURATION SE330”, or to an ICD file by clicking “Write to ICD File”. The SE-330 IEC 61850 interface can be configured with After writing the configuration to the SE-330, cycle SE- SE-MON330.
Page 6 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 3.2 R The Config Revision allows the user to maintain control EPORT ONTROL LOCKS The IEC 61850 interface includes four Buffered Report of the configuration revision. In a commissioned system,...
Page 7 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 3.3 D The GCB’s are configured to use the LLNO$DS3 Data Sets are used to group elements of the MMS data GOOSE Data Set. Refer to Section 3.4.1 for more model for use in RCB’s and GOOSE Control Blocks...
Page 9 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 3.4 GOOSE S The reception of duplicate GOOSE messages by a ETTINGS IEC 61850 GOOSE is used to provide network trip and subscriber can cause undefined behavior, so the redundant...
Page 10 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 FIGURE 9. SE-MON330 IEC 61850 GOOSE Tab. The Network Inputs are combined in a logical OR Equation 3.2 is the Boolean equation for the operation to drive the Remote Trip function within the SE- combination of the Network Inputs in the Remote Trip 330.
Page 11 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 TABLE 5. GOOSE N ETWORK NPUT TATUS ALUES TATUS ESCRIPTION The GOOSE messages are being received within the Time To Live period or the Network Input is disabled. No Data No GOOSE messages matching the Network Input configuration are being received.
Page 12 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 4. MMS D 4.1.1 R EPORT ONTROL LOCKS ODEL The LLN0 Logical Node contains four buffered and four The SE-330 IEC 61850 interface includes a single unbuffered RCB’s. logical device that contains multiple logical nodes. The RCB’s can be configured with SE-MON330 or through...
Page 13 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 • 4.1.2 F RecGGIO2.Ind12 (ST) IXED ATASETS • The LLN0 Logical Node contains two predefined Data RecGGIO2.Ind13 (ST) • Sets with following contents: RecGGIO2.Ind14 (ST) • RecGGIO2.Ind15 (ST) Data Set DS1_Measurement •...
Page 14 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 4.3 M UIRMMXU1 ETERING The Metering Logical Node contains data objects for the three metered values as listed in Table 8. TABLE 8. M UIRMMXU1 ETERING ESCRIPTION BJECT BJECT...
Page 15 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 4.4 G GFPTOC1 ROUND AULT The Ground-Fault Logical Node contains data elements that are associated with the ground-fault function of the SE-330 as listed in Table 9. TABLE 9. G...
Page 16 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 4.5 R RFPTOV1 ESISTOR AULT The Resistor Fault Logical Node contains data elements associated with the Neutral Grounding Resistor (NGR) monitoring function of the SE-330. The data elements are listed in Table 10.
Page 17 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 4.6 C CMDGGIO0 OMMAND The CMDGGIO0 Logical Node is used to issue remote trip and remote reset commands. The data elements included in CMDGGIO0 are listed in Table 11.
Page 18 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 reports for new event records as they are generated. A 4.7 E RECGGIO2 VENT ECORD BRCB will also send reports for all event records recorded The RECGGIO1 Logical Node provides access to the since the last power cycle or since the report buffer was last SE-330’s event record log.
Page 20 SE-330 Series (New Revision) IEC 61850 Interface Rev. 0-C-121117 APPENDIX A SE-330 SERIES (NEW REVISION) IEC 61850 INTERFACE REVISION HISTORY MANUAL RELEASE DATE MANUAL REVISION December 11, 2017 0-C-121117 June 9, 2014 0-B-060914 March 4, 2014 0-A-030414 ANUAL...