Advertisement
Ambient temperature
-10 to 45°C (No dew condensation or icing allowed), At storage: -20 to 60°C
Ambient humidity
Ambient Height
Material
Cable length
Cable extension
High-function type: extendable to 20 m with an optional extension cable (sold separately).
Tightening torque
Standard type
Approx. 70g (without cable), approx. 320g (including cable), and approx. 380g (with packing)
Mass
High-function type
Approx. 70g (without cable), approx. 110g (including cable), and approx. 160g (with packing)
Applicable regulations
Notes: 1) The following measurement conditions are applied unless otherwise specified; power voltage: 24V DC, ambi-
ent temperature: 20°C, sampling cycle: 500μs, average number of sampling times: 1,024 times, measure-
ment center distance, and measurement object: white ceramic.
2) The diameter is the size of the object at the measurement center distance and determined by 1/e
mately 13.5%) of the center beam intensity. The reflectance around the detecting point may be higher than at
the point due to leak light outside the specified area, and this may affect the measurement value.
3) Variance is ±0.1%F.S. or less depending on the ambient illuminance.
5
CAUTIONS
Connections
● Be sure to turn OFF the power supply before connecting or disconnecting any
connectors.
● When connecting or disconnecting the connectors, be sure to hold the connector
area not to apply extra force to the cable.
● Be careful not to touch terminals or to let foreign objects get in the connector after
disconnecting connectors.
● Be careful not to apply force to around the connector of sensor head cable and
extension cable. Do not bend the cables near connectors, which causes discon-
nection of the cable.
● When moving the sensor head during operation, install not to bend the cable dur-
ing movement. Use replaceable extensions cable where the cable needs to be
bent.
Wiring
● Do not roll up the sensor cable (bundle in parallel) with other wirings. Keep it at
least 100mm away from other wires. Cables should be separated from high volt-
age and power circuit lines. If it is unavoidable, shield it by running through a con-
ductive material such as grounded electrical conduit.
● Install the product as far away as possible
from noise source such as high-voltage
lines, high-voltage device, power lines,
power device, machines which generate a
large starting and stopping surge, welding
machines and inverter motor.
● Do not pull the cable with a force more
than 29.4N when wiring the cable when
the sensor head is fixed. The cable may be
bent with a radius of 30mm or over. How-
ever, do not bend the cable within 20mm of
the sensor head.
Warming Up
● Allow at least 30 minutes of warming up after turning on the power to ensure the
performance of the product.
Environment
● Mount the sensor head to an aluminum or steel plate with a minimum surface
2
area of 200cm
if the ambient temperature is 40°C or higher. In the case of install-
ing two or more sensor heads in parallel, mount each sensor head to an alumi-
num or steel plate with a minimum surface area of 200cm
ambient temperature does not exceed 40°C.
● The life of the semiconductor laser depends on the ambient temperature during
use. When using the product near a heat source, take measures to keep the am-
bient temperature of the sensor head as lower as possible. Mount the sensor on a
device having good heat radiation because the sensor itself also generates heat.
● Keep the emitter surface and the receiver surface clean, not to attach light refrac-
tors such as water, oil and fingerprints, or light blockers such as dust and dirt.
When cleaning these parts, wipe them off using a soft lint-free cloth or lens clean-
ing paper.
● Install the sensor head at where extraneous light (such as sunlight or light which
has the same wavelength as laser beam) do not enter the receiver. If high accu-
racy is required, install a light shield plate or the like on the sensor head.
● The sensor head has protection against immersion, while the connectors are not
structurally dustproof, waterproof, or corrosion-resistant. Do not use the product
underwater or in the rain.
● Do not use the product in dusty places or that exposed to flammable or corrosive
gases, droplet, direct sunlight, severe vibration or impact.
35 to 85%RH, At storage: 35 to 85%RH
2,000m or less
Casing: PBT, Front cover: Acrylic, Cable: PVC
Standard type: 5m; high-function type: 0.5m
0.8N·m or less
Conforming to EMC Directive
20mm min.
R30mm min.
2
and make sure that the
6
I/O CIRCUIT
● NPN Type
2
(approxi-
3.3V
3.3V
Sensor head
internal circuit
Refer to the HL-G1 Series User's Manual for RS-422
/ 485 wiring.
● PNP Type
Sensor head
internal circuit
Refer to the HL-G1 Series User's
Manual for RS-422 / 485 wiring.
7
APPLICABLE STANDARDS / REGULATIONS
● "SPECIFICATIONS" shows the product, the following
standards/regulations are relevant.
EC Directives: EMC directive
• Make sure that the length of signal and power lines
connected to the product is less than 30m in order to
meet CE marking requirements.
Attach a ferrite core to the head cable as shown.
Recommended ferrite core: SEIWA ELECTRIC MFG.
Co., Ltd.E04SR200935AB or equivalent one.
http://panasonic.net/id/pidsx/global
Overseas Sales Division (Head Office)
2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan
Phone: +81-568-33-7861 FAX: +81-568-33-8591
For sales network, please visit our website.
PRINTED IN JAPAN
Lead wire color
(Brown) +V
(Black) Output 1: OUT1
Load
50mA max.
(White) Output 2: OUT2
Load
50mA max.
(Gray) Output 3: OUT3
Load
50mA max.
(Pink / Purple) NPN / PNP type switching input
(Pink) Timing Input: TM
(Purple) Multiple input: MI
*1
(Blue) 0V
External connection example
Lead wire color
(Brown) +V
(Black) Output 1: OUT1
Load
50mA max.
(White) Output 2: OUT2
Load
50mA max.
(Gray) Output 3: OUT3
Load
50mA max.
(Pink / Purple) NPN / PNP
type switching input
*1
(Pink) Timing Input: TM
(Purple) Multiple input: MI
(Blue) 0V
External connection example
*1
Non-voltage contact or PNP transistor open collector output
IN
0V
High [5V to 30V DC (inrush current of 0.04mA max.)]: Enabled
Low [0 to 0.6V DC or open]: Disabled
© Panasonic Industrial Devices SUNX Co., Ltd. 2017
External
power supply
3 to 24 VDC
M a i n p o w e r
supply
24 VDC ± 10%
Ripple 0.5 V
(peak-to-peak)
included
*1
Non-voltage contact
IN
0V
M a i n p o w e r
supply
24 VDC ± 10%
Ripple 0.5 V
(peak-to-peak)
included
External
power supply
3 to 24 VDC
IN
or
0V
30mm max.
Advertisement
