Related Manuals for YEONHWA M TECH DX-8000 Series
Summary of Contents for YEONHWA M TECH DX-8000 Series
- Page 1 User Manual VHF Transceiver DX-8100 DX-8200 UHF Transceiver DX-8400 Version #1 (2018-07-03) YeonHwa M Tech Co., Ltd. 36, Jeonparo 44beongil, Manangu, Anyangsi, Gyeonggido, 14086 Korea Tel: 82-31-444-7270...
- Page 2 1. DX-8000 Series Features DX-8000 Series was developed with the user in mind to provide a compact and solid design with features to fit multiple types of tasks such as military, firefighting, construction site, industrial site and small/ large retailers.
-
Page 3: Specification
2. Specification DX-8000 Series General Frequency Range DX-8100 : 136~174 MHz Frequency Stability ±1.5ppm (-30 to +60℃) Programmable Channels 16 Zones / 32 Channels Channel Spacing 12.5KHz Digital Vocoder AMBE++ Dimensions 103mm(H) x 52mm(W) x 32mm(D) Weight 280g Power Source DC +7.4V Li-ion 2,600mAH Battery... - Page 4 * Components can be changed by the buyer requests. Radio Unit Battery Single Slot Charger Antenna Belt Clip Strap User Manual Figure 3-1) DX-8000 Series Main Package Contents XB-2600 : 2,600mAH Li-ion Battery Pack XC-100D : Single Slot Charger XC-200D : Dual Slot Charger 4 of 19...
- Page 5 4. Appearance of DX-8000 Series Radio 1. Power ON / 1. OFF Volume switch Turn the volume switch to the right to turn on the power and increase the volume. Turn it to the left to decrease the volume and to turn off the power.
- Page 6 Figure 3-2) DX-8000 Series Appearance of LCD 4.1 Button & LED Operations Button & LED Operation Description Turning the volume knob clockwise to power ON, volume up and turning Power ON/OFF the knob counterclockwise to power OFF, volume down. Press +/- button to control the call audio.
-
Page 7: Basic Operations
5. Basic Operations Please fully read the instruction manual before use. This manual provides convenient information related to radio operation. 1) Antenna Installation and Removal To attached the antenna connector, fasten the antenna clockwise. To remove the antenna, rotate it counter- clockwise. - Page 8 4) External Accessory Connector Jack Connect the external accessory as shown in the picture. Fix the main unit and the accessory by aligning them and tighten the screw. To remove the accessory, loosen the fixed screw. 5). Charging the Battery RED lamp indicates the radio is on the charger (XC-200D) that the unit is starting to charge and the LED will illuminate GREEN when the charging is completed.
- Page 9 Figure 6-1) DX-8000 Series Menu Figure 6-2) DX-8000 Series Menu Tree ☞ Caution) If you do not operate for more than 25 seconds after entering the menu, the menu mode is automatically ended and it switches to receive mode.
- Page 10 ICON shown in contact list : Individual contact list (individual calls, individual messages can be sent) - If the radio enable / disable and check / monitor functions are enabled You can run it from your contact list. : Group contact list (group call, group message can be sent) : All contact lists (terminals with the same channel and color code are available) 2.
- Page 11 party. Inboxes are managed with a maximum of 10, and if more than 10 are received, the received history is cleared and registered first. If you want to delete the inbox history, you can delete the whole delete menu. 2) Outgoing. A total of 10 call logs can be stored in the Outbox.
- Page 12 7 Setting It is a menu to set various status of the transceiver. Settings include transmission output, voice encryption, VOX, Ron Walker, BCL / BLCO, keypad lock, sound, rear, clarity, LED setting, language, screen and power saving mode. 1) Transmission output This function sets high (5W) and low (1W) of the transceiver transmission output.
- Page 13 7) Sound This is the effect sound setting function of this unit. ON / OFF is only provided in the main menu. Detailed sound effects can be enabled with the CPS program. 8) LCD BACKLIGHT It is ON / OFF function of LCD backlight. 9) Sharpness (LCD Contrast) It is a function to adjust the brightness of the LCD screen and can be set from 1 to 7 steps.
-
Page 14: Safety Operation
7. Safety Operation 7.1 Precautions Do not remove the antenna from the radio or do not transform the antenna or do not make any changes on the antenna. The strong electronic wave to be emitted from the radio can have an effect on the performance of the radio and can cause the radio to have a defect. - Page 15 7.2 Influences on the Operations of Radio or Other Equipment The radio emits a strong electronic wave, which may have an effect on the operation of other equipment and also can be influenced by the other devices. Please turn off the radio before boarding on the airplane. When using the radio in the airplane, please follow the rules or the instructions of the flight attendants.
-
Page 16: Safety Notes
8. Safety Notes Please make sure to read the followings above for safe and effective use of the radio. • Please keep the radio away at least 1 inch from the body. • If the outside surface of antenna gets stripped out, it can make a burn on the skin. -
Page 17: Warranty Statement
Warranty Statement Thank you for purchasing DX-8000 Series. 1. This product has passed strict quality control and testing process by YeonHwa M Tech. 2. Warranty is one year from the day of release. • When there is malfunction of the product under normal operating conditions during the warranty period, your authorized dealer and the service center will repair it free of charge. - Page 18 FCC statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
- Page 19 IC statement English Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1, This device may not cause interference. 2, This device must accept any interference, including interference that may cause undesired operation of the device. Safety Information This equipment complies with IC radiation exposure limits set forth for an controlled exposure environment.